Welcome to an extra bonus Sprue Tour, this was filmed ages ago (in Riyadh with no microphone as you'll see) and I totally forgot to upload it! So, here it is.
Жүктеу.....
Пікірлер: 22
@SMAZVidoesАй бұрын
Thanks for the review. I have been wanting to build a BoB Movie Buchon for a long time now.
@thescalemodellingcafe
Ай бұрын
You're welcome mate
@ronaldbyrne3320Ай бұрын
Jamie, I think I would build a Buchon just for that cobalt blue colour scheme with the yellow/orange roundels. 😍
@thescalemodellingcafe
Ай бұрын
It is lovely
@kitbusterАй бұрын
Quite familiar with the AZ 109 G series range, radiator opening are a bit small to see anything, the cockpit can’t be fitted from the bottom you can fit the exhausts later but the worry is you Push too hard you’ll Lose them, the gear legs have a decent positive fit and create the angles pretty well , I think you’ll like it when it’s built, a bit rough n ready but builds Into a decent kit , I enjoyed building them (done 3) The Bouchon kit looks 100% same bar the nose so comments above should apply minus the exhaust fitment Good luck with the conversion , hopefully see pics of it some time
@thescalemodellingcafe
Ай бұрын
It'll be a video build mate
@Greg420_scale_modelsАй бұрын
What a interesting little Aircraft ,thanks for showing. Great teeshirt too . I hope you got your TP for bunghole 😀
@thescalemodellingcafe
Ай бұрын
😂
@TheEdmond30Ай бұрын
Looking forward to this Jamie, looks to be a lot of fun. And making the best of short run kits isn't seen enough.
@thescalemodellingcafe
Ай бұрын
I'll be just using the nose and armament mate
@clra73Ай бұрын
The word buchón derives from buche (maw or throat), and it's given to some birds that can expand it.
@thescalemodellingcafe
Ай бұрын
Very appropriate!
@paulmanuse2353Ай бұрын
Look forward to that build!
@thescalemodellingcafe
Ай бұрын
Cheers Paul
@whotube220Ай бұрын
Thanks for the video, I wondered what this kit was like. I have Special Hobby 72308 - same airframe - SH looks like it might be the better molded of the two kits as the sprues are definitely different. If you encounter fit problems with mating the Eduard kit, this boxing may be an alternative route for you.
@thescalemodellingcafe
26 күн бұрын
Thanks for the info mate
@ljscalemodels526Ай бұрын
Very interesting subject matter Jamie.
@thescalemodellingcafe
Ай бұрын
It's a funky looking thing mate. Good luck with the retirement.
@justinboulton9655Ай бұрын
Lifecolour might be a good source for the blue.
@thescalemodellingcafe
Ай бұрын
I just don't get on with that stuff, I find it awful to use so I'll stick with GSI Creos which I have
@seanfoster3052Ай бұрын
I love the subject. I have the SBS conversion for the Tamiya 109. I got the nose one perfectly in a dry fit but the cannons are another story, they come as a set of PE and resin. While I got the PE on fine, the cannons are a nightmare. I ended up ordering a Mulberry 3D printed set as well as the rockets. How are you planning on adding the armenent to your aircraft?
@thescalemodellingcafe
Ай бұрын
I have that too but I'm going to try it on the Eduard kit. That Mulberry set is seriously undersized, the cockpit is at least 25% too small and the nose is 2-3mm too short in the vertical axis. I binned it. As for the armament, I'm just going to use the AZ bulges and shrouds and I'll replace the barrels with brass tube.
Пікірлер: 22
Thanks for the review. I have been wanting to build a BoB Movie Buchon for a long time now.
@thescalemodellingcafe
Ай бұрын
You're welcome mate
Jamie, I think I would build a Buchon just for that cobalt blue colour scheme with the yellow/orange roundels. 😍
@thescalemodellingcafe
Ай бұрын
It is lovely
Quite familiar with the AZ 109 G series range, radiator opening are a bit small to see anything, the cockpit can’t be fitted from the bottom you can fit the exhausts later but the worry is you Push too hard you’ll Lose them, the gear legs have a decent positive fit and create the angles pretty well , I think you’ll like it when it’s built, a bit rough n ready but builds Into a decent kit , I enjoyed building them (done 3) The Bouchon kit looks 100% same bar the nose so comments above should apply minus the exhaust fitment Good luck with the conversion , hopefully see pics of it some time
@thescalemodellingcafe
Ай бұрын
It'll be a video build mate
What a interesting little Aircraft ,thanks for showing. Great teeshirt too . I hope you got your TP for bunghole 😀
@thescalemodellingcafe
Ай бұрын
😂
Looking forward to this Jamie, looks to be a lot of fun. And making the best of short run kits isn't seen enough.
@thescalemodellingcafe
Ай бұрын
I'll be just using the nose and armament mate
The word buchón derives from buche (maw or throat), and it's given to some birds that can expand it.
@thescalemodellingcafe
Ай бұрын
Very appropriate!
Look forward to that build!
@thescalemodellingcafe
Ай бұрын
Cheers Paul
Thanks for the video, I wondered what this kit was like. I have Special Hobby 72308 - same airframe - SH looks like it might be the better molded of the two kits as the sprues are definitely different. If you encounter fit problems with mating the Eduard kit, this boxing may be an alternative route for you.
@thescalemodellingcafe
26 күн бұрын
Thanks for the info mate
Very interesting subject matter Jamie.
@thescalemodellingcafe
Ай бұрын
It's a funky looking thing mate. Good luck with the retirement.
Lifecolour might be a good source for the blue.
@thescalemodellingcafe
Ай бұрын
I just don't get on with that stuff, I find it awful to use so I'll stick with GSI Creos which I have
I love the subject. I have the SBS conversion for the Tamiya 109. I got the nose one perfectly in a dry fit but the cannons are another story, they come as a set of PE and resin. While I got the PE on fine, the cannons are a nightmare. I ended up ordering a Mulberry 3D printed set as well as the rockets. How are you planning on adding the armenent to your aircraft?
@thescalemodellingcafe
Ай бұрын
I have that too but I'm going to try it on the Eduard kit. That Mulberry set is seriously undersized, the cockpit is at least 25% too small and the nose is 2-3mm too short in the vertical axis. I binned it. As for the armament, I'm just going to use the AZ bulges and shrouds and I'll replace the barrels with brass tube.