(SPRAY PAINT) Your Car At HOME Pt. 2 (How To Cut & Buff) For A SHOW CAR FINISH
Автокөліктер мен көлік құралдары
This was a Fun but tiring video. I had wins and fails in this video but we got it done!!! In this video we started with a very bad orange peeled spray paint job and turned it into a slick show car finish. I used all pretty primitive tools to get this process of wet sanding and buffing the paint to perfection. This process is pretty simple but labor intensive!!! So follow along get your sand paper and buffer and get to doing some satisfying paint correction.
Links below are from my amazon affiliate account, I make a small percentage off of qualified purchases at no additional cost to you.
Paint Shaker 4000 Video Link • Build your own FREE (S...
Links Below
My Website to buy Shirts www.acdesignsgarage.com
My PO Box Below:
PO Box #782 Troutman NC 28166
Sprayway Glass Cleaner amzn.to/44q4ntY
Variable Speed Polisher amzn.to/3UmNID7
Rupes Big Foot 21 DA Polisher amzn.to/3QuuRon
Dewalt cordless drill amzn.to/3lc3aAQ
3 inch buffing kit amzn.to/3FKHpBr
Dura Block Sanding Block amzn.to/3JIJXCX
foam sanding blocks amzn.to/3FIYgoc
m105 compound amzn.to/3wsUqeL
m205 polish amzn.to/3FKHhlo
3m wet dry sand paper amzn.to/3L8FN5P
1500 and 2500 grit
Soft sander Foam block amzn.to/39mAToD
water spray bottle amzn.to/39j2O8L
233 tape amzn.to/3FMISHB
scott shop towels amzn.to/3Pjox0N
micro fiber towel amzn.to/3wgg9YF
Rust-oleum turbo can amzn.to/3UBsYbZ
Mineral spirits Paint Thinner amzn.to/3PXPh94
Red Scotch Brite amzn.to/4aGRdeb
Sprayway Glass Cleaner kit amzn.to/4aMaWt1
3m Mask amzn.to/4a0zrmk
HOSE CLAMP amzn.to/48EO2C8
Sawzall Blade amzn.to/3P6A2ua
Sawzall amzn.to/4bYG7Cv
isopropyl alcohol amzn.to/3WdGPGM
Scott shop towels amzn.to/4demzuG
tac cloth amzn.to/4bgdFv4
3m 233+ 1 1/2" tape amzn.to/3wcdfGW
12 inch masking paper amzn.to/4dhJO75
Пікірлер: 258
I never woulda believed it, if I didn't just see it. Incredible job!
@ACDesignsGarage
4 сағат бұрын
Hahaha thank you!!!!
I knew nothing about painting a car! Thanks so much for your video I really appreciate it!!
@ACDesignsGarage
26 күн бұрын
Thank you very much for watching!!!
Dang, that looked like a workout. Shined up good though. Nice work. So many good tips. Thank ya, sir, for going to the trouble.
@ACDesignsGarage
Ай бұрын
Hahaha it was, I wouldn't of been as bad if it wasn't as orange peeled. That was my fault spraying to close to the pannel. Im not use to them turbo cans but I like em!!! Thanks for watching!!!
@RMCUSTOM
Ай бұрын
It’s a work out for lazy slobs !
Words I've never heard..."'I' got to many trucks". Thanks for the great drops!
@ACDesignsGarage
Ай бұрын
Hahahaha your right, its kinda like a savings account lol
Keep going with this truck...the impact of the total job will be beyond impressive...a total job is going to inspire viewers and that is the core of this channel 😉
@ACDesignsGarage
Ай бұрын
Thank you for the idea we may try a full build spray painted if yall want to see it!!!!!
you are a great teacher. I love your accent and how you talk about what is going on. Keep up the good work. You are authenitic.
@ACDesignsGarage
Ай бұрын
Thank you very much!!
I have two different trucks that I have been needing to get painted but I have never painted a vehicle in my life before!! I’m also definitely not good at mudding and taping a house out either so if I can’t do a good job mudding and taping a house out I’m definitely not going to be good at doing a vehicle either!!! I can’t afford to have someone do a paint and body work on my trucks either so I’m just going to have to try and do it myself!!! After watching all your steps that you go through has definitely helped me out on what I need to get and what to do!!! I think if I just do one panel at a time and just take my time and follow your steps I keep telling myself I might be able to pull it off hopefully!!! I have a 1972 Chevy K30 with a 1969 grill in it and the other truck I need to get painted is a 1981 Chevy K30 also!!! I have gotten all new sheet metal for my 1972 and all the sheet metal on my 1981 is good except I do need to find a decent 8’ box with dual square gas doors for it!!! Can I paint the front half of the truck now and then when I’m able to find the correct box for it could I paint it then or should I paint it all at the same time??? I’m thinking of painting it white or a two tone white and blue!!! What are your thoughts on that?? It does stay in my shop most of the time since it is big enough!!! I built a big shop 60’x80’x16’ so I’d have enough room for all my good trucks and so they wouldn’t have to sit out side all the time also!!! After I got my shop put up after building are house 20 years ago I definitely wish we would have put one up much sooner for sure!!! Awesome video and I’m definitely glad I ran across your channel for sure!!!
Looks freaking amazing!!! Wowza!
@ACDesignsGarage
Ай бұрын
Thank you!!!!!
Enjoyed the video! Thanks for the hard work! Looks great, looking forward for the next video!
@ACDesignsGarage
Ай бұрын
Thank you for Watching!!!!!
I wanna thank you. I followed your instructions after rattle canning (turbo white) the suburban. No clear coat and just did cut and buff on paint. Holy moly, I wish I knew about this before because it makes a huge difference. I did use flash light to see orange peel in between sanding. I used different waxes, and will buy Nu Finish to add to this. Mine will have black truck bed liner on bottom half to help hide body work and clear or white bed liner on roof.
@ACDesignsGarage
9 күн бұрын
That's so awesome, so glad it helped, I just bought a 87 surburban last week. I showed it off on last week's video!!!
That is gorgeous bub nice!
@ACDesignsGarage
Ай бұрын
Thank you very much!!!
You Sir are a MASTER at what you do. That was more than I've learned from other detailers in my 51 years. Thank you for the EFFORT you put into this my friend. GOD BLESS YOU AND FAMILY. Much Love from Australia.....just subbed👍🍻🙏
@ACDesignsGarage
22 күн бұрын
Thank you very much for the support, Its greatly appreciated!!!!
Beautiful!
@ACDesignsGarage
Ай бұрын
Thank you!¡!!!!
Very good job, especially for black.
@ACDesignsGarage
Ай бұрын
Thank you!!!!!
You are the best i have seen with spray cans.leslie from canada.
@ACDesignsGarage
20 күн бұрын
Thank you very much for your support!!!!
Looks fantastic for a spray can!!!
@ACDesignsGarage
Ай бұрын
Thank you!!!!
Great job looks great especially for a rattle can
@ACDesignsGarage
Ай бұрын
Thank you very much, I wanted to show with a little bit of elbow grease you can get quality jobs with rattlecans, just wait for this weeks video!!!!
looks good brother. only thing I could say is use a microfiber when you are wiping off the buffing compound and you will have a much easier time keeping the shine on new paint.
@ACDesignsGarage
11 күн бұрын
Thanks, the problem I had os that enamel is gooey when you start buffing, it tends to mar that compound lol. But your right I love them microfiber rags!!!!
@3GermanCars
11 күн бұрын
I totally understand that stuff isn’t the same as a two part with a hardener for sure. Great job though.
Thanks for the education turned out nice
@ACDesignsGarage
Ай бұрын
Thank you!!!!!
Awesome job
@ACDesignsGarage
Ай бұрын
Thank you!!!!
Yea after I watched your video plus others I went did body work and I went with Rust oleum gloss charcoal grey on my 2001 impala. I left side mold black but painted the skirts. Now I put on lot like 6 cans of clear and yea its gonna need wet sanded then buffed. Already got heads turning and any body man or anyone knows about painting knew I have yet to wet sand then buff out..everyone I talked to said they never seen 01 impala in New color on these cars seen today. Plus way it runs..I replaced all the major parts on her and once I buff her out she gonna shine like new money. Then I'm gonna start working on inside and like put different seats in front..like bucket seats.
Excellent
@ACDesignsGarage
Ай бұрын
Thank you!!!!
Great job looks awesome! Thanks for sharing
@ACDesignsGarage
22 күн бұрын
Thank you for watching!!!
I subscribed because of good content and he said "Good Gavy"
@ACDesignsGarage
Ай бұрын
Hahaha thank you for watching!!!
Excellent video. Subbed! Ready for what’s next.
@ACDesignsGarage
Ай бұрын
Thank you for watching!!!!
Great video
@ACDesignsGarage
Сағат бұрын
Thank you!!!!!
I love harbor freight love tools and that looks great 👍
@ACDesignsGarage
Ай бұрын
I call harborfreight the man mall lol, thanks for watching!!!
I think that looks really good I've been happy with that on my truck I spray bombed it in white I got cans mixed at the parts store for the factory color and them can suck compared to using the Rust-Oleum in a can I didn't do the cut and buff or the wet sand but I might try that to see if it'll make it shine like yours did cuz mine look dull
@ACDesignsGarage
18 күн бұрын
I love my rustoleum, they have stepped up the spray paint game for sure!!!!
Doing great!! Love the darker blue better! Lighter blue was very Suttle. Over a red candy metallic, what pearl would you suggest adding to the clear?
Nice work sir 👏
@ACDesignsGarage
22 күн бұрын
Thank you very much!!!!
Wow impressive 👍
@ACDesignsGarage
22 күн бұрын
Thank you very much!!!!
Pretty impressive for a rattle can job !
@ACDesignsGarage
Ай бұрын
Thank you very much!!!!!
Nice work 👍
@ACDesignsGarage
Ай бұрын
Thank you!!!!
I did a hood like this. If you buff it with Meguires cleaner wax after you cut and buff it makes it look like a mirror.
@ACDesignsGarage
Ай бұрын
I love the meguiars products, ill try that!!!!
Dam man that looks great good job 😊
@ACDesignsGarage
22 күн бұрын
Thank you !!!!!!
Nice! Thx!
@ACDesignsGarage
Ай бұрын
Thanks for watching!!!
Definitely the best turbo can video I've seen so far. I'm a New subscriber! I'm going to go back and watch some of your other videos! Great job & Great video!!
@ACDesignsGarage
Ай бұрын
Awesome thank you very much!!!
Hey Sir out of all the painters you the only one, who said how to use the grits sanding question, I need to do my rear third light and the paint is peeling up, what type of sanding and primer to use it jet black.,iam your 1fan now
If you use machine glaze with a black or white pad .. will more than likely get rid of all the haze and make the black more deep. It will look 100x better
@ACDesignsGarage
24 күн бұрын
Thanks for the tip, That enamel is the hardest thing I've ever buffed. I put some of the 2k clear over it and buffed it and it looks amazing, here is a link to this weeks video kzread.info/dash/bejne/YnelzKWYZ8-elMY.htmlsi=4ZEP9e3iOegpULDK
Real life problems that the rest of us out here will have. Really enjoyed the content and learned a few things. 👍
@ACDesignsGarage
Ай бұрын
Thank you, I try to help everyone at every level!!!
Thank you for this series, I learned a ton .wow!
@ACDesignsGarage
Ай бұрын
Thanks for hanging out with me!!!
Great job and I admire your honesty, patience and genuine effort to make it right. God Bless You!
@ACDesignsGarage
Ай бұрын
Thank you hope you have a Blessed day!!!!
It’s really hard to believe the paint job started from a basic can of rust oleum. Amazing!
@ACDesignsGarage
Ай бұрын
Thank you, hopefully next week were gonna do a show car quality spray paint job!!!!
That looks great! But that is coming from a beginner. You being a professional painter it may look subpar. For a hot rod and not concours I would be 100% happy with how it turned out. I have a ‘59 Apache and a ‘61 olds 88 that may get this treatment. I guess it depends on what colors are available in those big cans. I do know that good bodywork is the key to a decent finish. Thanks for doing these videos and making them long enough to follow along.
@ACDesignsGarage
Ай бұрын
Thank you, yeah it could stand a little more but it turned out pretty good for what it is, lol. Those new rustoleum cans with the different settings work prett well. Im going to do a video next with the little cans, then shoot 3 coats of 2k clear over it, then buff it. It should look like a show car with all spray paint !! Sounds like you have some awesome projects!!!!! Thank you for Watching!!!!
Amazing results ! Thanks for the time and the tips! So after the cut and buff, is it just waxed to protect it?
@ACDesignsGarage
Ай бұрын
Thank you!!! Yes if you have swirls you can use a glaze polish to remove then then a good carnuba wax. The only down fall is the spray paint won't hold up very long. This weeks video is on how to put 2k spray paint clear that will make it last for a good while!!!
So can you polish the other half with compound without wet sanding and get the same results?
Looks awesome for what it is. Have you seen that denim pad that is supposed to remove orange peal on its own. saw someone use it here on youtube somewhere
@ACDesignsGarage
Ай бұрын
No I need to check that out!!! Thanks for the tip!
You definitely need a wool pad for the big buffer and not use the foam to cut the clear alot faster initially ,had you done that you would of finished in half the time for sure
It turned out as good as the paint on a new car with less orange peel but your haze is from cutting too dry, gotta stop when it turns to gum or it just blends in but i wouldn't be afraid to use that turbo on my old truck but id definitely clear it just for that extra protection
Impressive! A lot of work. How would you fix the red spots?
@ACDesignsGarage
Ай бұрын
If you was gonna clear it you could lightly wet sand in 800 grit spray a lil paint over the red spots then clear the whole pannel. If you were going to just sue the rustoleum you would have to sand it with 600 grit the spray the whole pannel. Not really a easy way to do it lol!!!
im really impressed at how good those turbo cans do im gonna paint my old truck with those i think
@ACDesignsGarage
Ай бұрын
They are pretty impressive, you can paint a bedside in 2 swipes lol
Im curious to know if you've ever used the Sonax brand of compound and polish? That stuff is amazing. I'll never use Mother's again.
@ACDesignsGarage
Ай бұрын
I'm game to try it, but I haven't yet!!!
Great video. Can you do a video using poppies patina, Wipe on clear coat. I want to use that then Cut and birth to a high gloss
@ACDesignsGarage
24 күн бұрын
I may look into that, I've heard of it but have never tried it before.
That looks great! In the past, I’ve had issues with rustoleum enamel fading from the sun, but a clear coat prevented that. Does this cut/buff process help, or do you still clear coat it?
@ACDesignsGarage
Ай бұрын
The clear will help it last longer, then you can cut and buff it for a show car shine!!! Hopefully next week im gonna do a clear coat job on the other side!!!!!
@brodyharrison6029
Ай бұрын
@@ACDesignsGarage Awesome! Can't wait for the video!
Wow! Such a awesome job there!
@ACDesignsGarage
Ай бұрын
Thank you very much!!!
Good tutorial shines like glass is good to sand in an x pattern for clear coat as well as other surfaces makes it go quicker i m h o
The truth is that you are a professional, wow tremendous and the truth is that I enjoyed it a lot, thank you and may God continue to give you much more knowledge so that you can continue sharing it.
@ACDesignsGarage
Ай бұрын
Thank you very much, hope you have a Blessed day!!!!!
@RMCUSTOM
Ай бұрын
You need to get out more pal !
It is possible to sand paper the burn clear and cut to give the shine again or we have to spray clear again then do the whole process? Is for my acura tsx and i live in Florida
@ACDesignsGarage
Ай бұрын
You can try, but your best result will come from sanding it down and reclearing. The reason it looks burnt is because the clear is super thin. One trick you can do is wet the area with water and that will usually tell you what it will look like when cleared.
When would you add clear coat during this process? I'm painting my hood Thursday n wanted to put clear on it after the can. Thanks man. Perfect timing
@ACDesignsGarage
Ай бұрын
Awesome Im doing a video this week but it wont be out till Friday. The way I do it is if your painting your color, get a couple coats of it down till covered then let it tac. I like to check a spot on the paper or tape that has paint on it. It should be barely sticky, not stringing when you pull your finger off of it, and then I shoot the clear. If your just clearing a dry surface youll need to wet sand it with 800 grit to give it something to bite into or it will peel off later
@jasonv1144
Ай бұрын
Thanks for replying. Just another question. Shouldn't I wet sand it anyways after base coat? I'm assuming ill have orange peel. Then shoot clear after that. Thanks again. Maybe ill wait a day and watch the video
How would you maintain the gloss ? Waxing /polishing or can you clear over it ? . I took my old 69 pick up to a crooked body shop he promised me a decent paint job at a fair price 2,000 dollar deposit my truck sat in his shop for 2 months no work done to it but stripping and ruining a lot of my classic trim . I went every weekend and asked about the progress so he got frustrated with me and started zipping on the truck with a flap disc 😮 to look like he was working on it 😢. I finally asked for my keys 3 months later drove it out with no windshield no taillights all my stuff in a box and took her home then I had to use a rattle can to try to color match it to look decent but it needs this kind of lovin.
@ACDesignsGarage
25 күн бұрын
I hate that, for some reason people don't wat to work for some reason. As for maintaining it you can keep polishing it but it will get thin. The best way to do it is 2k clear over that spray paint. I did a video this week on buffing that 2k and it looks amazing. The week before I showed how to clear over the turbo can. I'll put a link below on this weeks video if you want to check it out. Thanks for watching!!! kzread.info/dash/bejne/YnelzKWYZ8-elMY.htmlsi=Z2zNfjquZo0qrr0F
Can a man just start with 2500 grit to clean up scratches on a single stage old paint to get the oxidation? Keep up the great work/ content.
@ACDesignsGarage
Ай бұрын
Yeah man that should work pretty good. If it's really bad just drop back to 2000 the 2500 and buff, just depends on how bad it is. Thanks for watching!!!!!!
Nice work !
@ACDesignsGarage
Ай бұрын
Thank you very much!!!!
That’s really impressive
@ACDesignsGarage
Ай бұрын
Thank you!!!!
Looks good, what part of NC are you from, i live in Eastern NC!
@ACDesignsGarage
Ай бұрын
Just north of Charlotte
wow that’s a lot of work. looks great though.
@ACDesignsGarage
Ай бұрын
It was like 5 hours lol!!!
Damn all the work for a rattle can paint job hmmmm.... 🤪🤪🤪
@ACDesignsGarage
Ай бұрын
It's alot of work lol
The problem is you cant thin the paint further than how it is in the can that's why I use a good quality spray gun at the proper pressure.as the more you spray from the can the lower pressure you end up with but not a bad job for a can.
@ACDesignsGarage
22 күн бұрын
Thank you!!!!
Awesome video Great work !
@ACDesignsGarage
Ай бұрын
Thank you!!!
Never have too many trucks.
@ACDesignsGarage
Ай бұрын
I agree lol
Don't know about you but I'd be calling all my friends to show off that I have those buffing skills from a rattle can paint job. I hate to ask what is the order in using the sand paper ? I'm about to paint my son's car with rust -oleum but trying it with a spray gun. Sad part I don't have a garage so its outside for me any advice on the mixing ratio for the rust -oleum with acetone. Bueno sir be standing by for the next one. Like to see those slotted mags 5 or 6 lug
@ACDesignsGarage
Ай бұрын
Thank you very much!!! You may want to try the turbo can, its pretty impressive, ill put the link to the video where I sprayed that bed side with the turbo can. I haven't tried spraying it through a gun yet. I will say in my years of painting make sure to follow the directions to the max, and you'll have success!!! This comming week im going to rustoleum turbo the other bedside then spray it with the 2k spraymax clear then buff. That clear will make it last for years and buff like butter!. Ill try to remember to show the slots, there 5 lug small chevrolet pattern 5 on 4 3/4.
@bJamesm-bj6ur
26 күн бұрын
Mix for spray gun job should be 1 to 1
@rudyflores9395
26 күн бұрын
@@bJamesm-bj6ur thanks
looks good man
@ACDesignsGarage
Ай бұрын
Thank you very much!!!!
Looking forward to listening/watching tthis. I’m on the Ford assembly line. Occasionally I can take a glance.
@ACDesignsGarage
Ай бұрын
Awesome thanks for listening and watching!!! I bet thats an awesome job!!!!!!
@RMCUSTOM
Ай бұрын
No one cares about you or where you are !
@briansawdo6245
29 күн бұрын
It has its good days and bad days
See what a turbo can rustoleum black paint job with 2k clear with a 3step cut and polish would look like ? Just curious
@ACDesignsGarage
Ай бұрын
The painting part will be this Friday, then the cut and buff next week, keep an eye out!!
@OGKILLa9365
Ай бұрын
@@ACDesignsGarage sounds good. 👍
👍👍
The First Coat Looked Way Better than the Second Coat on your Truck Bed. I did my SUV Spray In A Can Anodized RED and it has a color Change in it So on a bright day it is a Cherry RED and in the Shade it turns Dark Cherry RED It Looks Awesome and I also Did all of my Plastic Interior Trimmings. I also did the Star the Same color on my Aluminum Star Wheels it started to chip off on the Wheels because i was Supposed to Clearcoat the Aluminum Wheels First then when dried and spray on the Anodized RED and let that Dry and Clearcoat it. Anodized paints Only works with Chrome for it to work, so what i did I sanded my SUV right Down to the Chrome Metal then Clearcoat it and then Sprayed on the Anodized Cherry RED and after it was dried then Sprayed Clearcoat to lock in the paint. It's like a hamburger the bun is Clearcoat the meat is your Cherry RED and the other bun is your Clearcoat you need to sandwich it in, that's what a Autobody Shop Guy Told me to do.👍
@ACDesignsGarage
Ай бұрын
Yeah I agree, I will say that turbo dumps paint and makes it orange peel bad. The other cans do much better. I'll have a video on doing a show car quality paint job with spray paint soon. Man that sounds like a cool color on your SUV, ill have to try that!!!
@newfie66xbox76
Ай бұрын
I didn't do a video i wish i did so you could see it, but I guess I can make a Slideshow Video i have Pictures of it, I also Custom design Builds of LED Lighting for Vehicles and Motorcycles and marine Boats like Pontoon boats I build LED Light Bars I did all of the lighting on my SUV there Isn't a Stock bulb left in the SUV It is all LED Lighted Now and My Light Bar puts out in Lumens 300,000 in Brightness.👍
@newfie66xbox76
Ай бұрын
@@ACDesignsGarage I was thinking that the spray paint that you used could be different thinners than the Autobody thinners that they use, that might have made the Second Coat bubbly that you did.
I ment to ask that could I use 800 grit to wet sand if it be safe to and not leave scratches once I buff it?
@ACDesignsGarage
11 күн бұрын
I'd be scared that you couldn't get those scratches out, you could go from 800 to 1000 to 1500 to 2500. Or just go 1500 if you have peel then up from there. I don't usually buff till 2500 because it's easier.
@urbanX4you
9 күн бұрын
@@ACDesignsGarage I went got 1500 to 2000 but now should I use micquires polish to buff or compound I keep getten different stories
Very nice, for one part enamel! I, know it was a ton of work!
@ACDesignsGarage
Ай бұрын
Thank you it was tough!!!!
So now that this is cut and buffed, can you clear coat over that to protect it? Or are you supposed to just leave it bare paint
@ACDesignsGarage
Ай бұрын
You can clear over it but youll ha e to wet sand with 600 or 800 then clear so it has a mechanical bond.Im going to try to do a clear coated video this comming week!!
@joshramsey8450
Ай бұрын
Ok so basically you would just cut but not buff. So you could spray the clear on it. Then cut and buff the clear. Man that is soo much freakin work !!
@ScardyVAL
29 күн бұрын
@@joshramsey8450 Typically you spray clear on before any sanding any paint. Only time you need to sand is if you get runs or orange peel in your base and that's usually user error lol
Would the residue blow out with compressed air or is it too gummy?
@ACDesignsGarage
24 күн бұрын
It helps bit that stuff is so soft it still gums up. I did a video this week on cut and buffing the 2k clear over the rustoleum and it was amazing!! I'll put yhe video below kzread.info/dash/bejne/YnelzKWYZ8-elMY.htmlsi=QorfqlmZATDdXB2c
@07bluelbz
24 күн бұрын
@ACDesignsGarage I already watched it. Turned out amazing. Nice work!
I tell you I did 2 bumpers on my tahoe with a spray can in black.. wet sand 2k then 5 k then 7k and buffed with the machine but like you kept getting the dry residual from the polish ,then I used the 3in pad on a drill man what a difference and the shine was great ..no I didn't clean with 2k because I wasn't sure if it would take .but I figured if it don't hold up I can always repaint it and clear it next time ..great job showing all your detail and imperfections that's true reality
@ACDesignsGarage
Ай бұрын
Awesome thanks for watching, your doing it right ,just jump in there and figure it out!!! I had the same problem when buffing. I guess it softens up when buffing! Thanks!!!
What's the Captain Morgan to Pepsi ratio? For future reference that is.
@ACDesignsGarage
Ай бұрын
Hahaha shes just straight pepsi lol
If you are going to use that type paint use a pint or a quart in a gun that loads from the top a small one for cars and it will save you a lot of sanding
@semcmutry12
Ай бұрын
And better finish
@ACDesignsGarage
Ай бұрын
Yeah I have a ton of spray guns, i was doin it this way for guys that dont have any spray guns or Compressors.
@semcmutry12
Ай бұрын
Understand keep up the good work
Came out great! Let me tell you thought, the ONLY pad and polish you ever need is 3d-one (it’s a compound that finishes down perfect every time) and with rotary and a rupes medium wool cutting pad you can do any paint unless it’s a extremely hard clear coat. -Autobody hobbyist 15ish years.
@ACDesignsGarage
Ай бұрын
Thank you for the tip!!!!
Good content very informative thanks for doing it ...
@ACDesignsGarage
Ай бұрын
Thank you for watching!!!!!
Really good work man! Next week when you do the other side with the 2K clear, make sure you shoot the 2K when the rustoleum is still tacky. If you let it dry, you’ve got to wait for the rustoleum to completely dry which could take weeks.
@ACDesignsGarage
Ай бұрын
Thank you for the tip, ill definitely do that!!!!
Wet your pads and clean the paint out of them often.
@ACDesignsGarage
20 күн бұрын
I agree, this enamel goo's up the paper pretty bad , it sat for a week in the sun lol
Next time use the da sander and which one do you use
@ACDesignsGarage
26 күн бұрын
Dynabrade is my favorite, I also have a Ingersoll Rand that's pretty good!!!!
Nice vid except for one thing. I've done plenty of cut and buff on cars throughout the years. One thing I didn't care for is how you were sanding the paint horizontally on the curved sections. There I like to do the criss cross method. With a bodymans eye I could see the problems after you buffed it out. But that's OK. Everyone watching your video didn't see it. But I could see the problem with you sanding the curved sections left to right and vice a versa.
@ACDesignsGarage
Ай бұрын
Thanks yeah I normally dont sand good cars like that but that enamel is a gooey mess. It sands like garb lol. After 4 hours of sanding I about had enough of it and It was cutting through so I stopped lol, ill drop a link to some of my real work to help redeem myself lol kzread.info/dash/bejne/Y6BplaR-k8XVn6w.htmlsi=z0FaCjzlJ0DGrxkj
I really enjoyed the video. Quite a workout for you! And it turned out nice, so good job. I'm looking forward to next week's video of you showing us how you paint with a gun/compressor plus clear coating the panel. I would appreciate any info you can share about a beginner setup (gun and compressor). Thanks
@ACDesignsGarage
Ай бұрын
It was rough, thank you for watching!!!
The cutting part is what scares me. Im happy to do everything else but the cutting part makes me nervous. Im prepping to rattle can restore my 1987 honda Ballade/ Civic.
awesome demo
@ACDesignsGarage
22 күн бұрын
Thank you very much!!!!
Could you put a link the music you use in this video sir?
@ACDesignsGarage
Ай бұрын
I cant remember the name, i use epidemic sound for my music
What number are you running that on?
@ACDesignsGarage
Ай бұрын
This can here only has one setting. The other new cans I like the number 5 setting.
Great job brother made a spray can look like cost paint 👍
@ACDesignsGarage
Ай бұрын
Awesome thank you!!!!!
what if you sand it and clear coat it
@ACDesignsGarage
Ай бұрын
Im going to do that hopefully next week, it should do a great job!!
Its either good advice and what works instead of a bunch of excuses for a failure
@ACDesignsGarage
Ай бұрын
All of it works I just show the problems that come up and how to fix them instead of editing everything out and say its all peachy .
Do it in the shade
@ACDesignsGarage
26 күн бұрын
I know lol it was to hot!!!
Did you work at Gaines and company of three sister road
@ACDesignsGarage
Ай бұрын
No I haven't.
@anthill7327
Ай бұрын
@@ACDesignsGarage wonder how I know you
@anthill7327
Ай бұрын
Can you tell me where you at in nc
@anthill7327
Ай бұрын
I'm in Rocky Mount
Good on ya for leaving in the da death...and ya can run it on the other side ... 1:18:28
@ACDesignsGarage
Ай бұрын
Thanks for watching!!!
whats the use when u spray with aerosol when gonna end up orange peel, when u can use air comp: adjusted the air to 25 psi to get fine coat loll, when u have to sanded to remove orange pell,u drinking to much coca cola,theres many try to share with others, i only look at the guy BRIAN ,( paint society) that guy is immaculate,
@ACDesignsGarage
Ай бұрын
I have $900 paint guns and have been custom painting for 25 years but I wanted to help out guys that dont have a shop ,air compressors and paint guns to give them the ability to paint there own car for cheap. I watch @paintsociety love his channel. He also has done many videos with spray paint. The main reason for the peel is using that turbo can that Everyone wants to see, that thing dumps some paint lol thanks for watching!!!!