Thanks your setup video was the most concise of all I watched on you tube. I was amazed how much of a leap in technology the AR737T is & the ease of programming

This would all be great except it can't save different setups for each plane to reload later like you were able to do to the your computer using the progrramming cable and app. As a result you have to buy a reciever for each plane or hand reload as you switch out the reciever from plane to plane.

I have 6 of the now discontinued AR636s and am afraid that the AR637T is a step backward... I have twin engine aircraft with differential thrust mixed in with AS3X roll resulting in stabilization of yaw via differential thrust. I also have bomb drop on a separate channel that's output on the throttle port on the AR636. These are all settings defined in the AS3X Programmer application. I can't for the life of me figure out how to replicate these types of configurations on the new AR637T. Ironically, the brand new AR9350 retains these capabilities... I hope I don't have to switch to 9 channel AR9350s just because the AR636 is discontinued and the AR637T can't do what the AR636 did... Yeah, it's cool that you can set up the AR637T from the transmitter, but it's a waste if you have to neuter the AR636 replacement to do it.

Where is the advanced features video ?

Hi, thank you for these videos, they were much needed. I have a perfectly tuned plane with the AR636 receiver, but I want to upgrade to a complete SMART eco system, including the SMART ESC, can I copy my settings from the AR636 with SAFE to the AR637 T? Thanks again and look forward to the rest of the videos.

Which one is better the aura 8 or this ar637T?

I tried and think I failed to follow the video using a G2 DX6. I finish having three flight modes. SAFE, AS3X only, and no AS3X. In the AS3X mode, I cannot detect any AS3X correction after running up the throttle. SAFE works but AS3X seems the same as no AS3X. I wish there was a video of the DX6. It is only 1 1/2 years old. Is it that obsolete?

Hi I Purchased AR630 and i have done as3x step by step programing by my dx9 and my motor is not running ,when i restore receiver to factory setings its ok , after programing as3x it wont run. Any ideas?

I setup my AR630 on a DX8G2 and got ASX3 to activate. I set the gains on the potentiometer like you show but only get very slight servo movements. I’m talking so slight that I can hear them move but can’t actually see them move. Is there something else I missed?

@SpektrumRCvideos

3 жыл бұрын

Sounds about right. It can be difficult to see depending on the control surface, servo geometry etc. One great tip is to put your finger on the control surface while you manipulate the model to "Feel" the movement. Hope that helps!

What spektrum remote receiver is compatible?

I wanna know why my as3x won’t turn on unless I put I. Heading. Why is this ?

I’m doing this on my dx8 g2 and it’s not letting me do some of the stuff ur talking about and I’m following step by step

@SpektrumRCvideos

4 жыл бұрын

Cesar Maldonado make sure your tx is completely up to date

@cesar68033

4 жыл бұрын

SpektrumRC I’ll check for a new update

@cesar68033

4 жыл бұрын

SpektrumRC I set it up that’s it’s always on safe the 3 modes are always set to my flaps and I want them on channel f maybe I’m missing something hopefully I’ll get it soon but for now it’s not working for me

This video is missed labeled ..... Chapter 7 but it says chapter 8 your missing a chapter.

This videos are very excellent and often worth a purchase decision. If you could just turn that background music off that adds noise nothing but noise. To make the man harder to understand. Please turn the noise off you do yourself and your company a giant favor. Just because everyone is doing it doesn’t make it any good

@SpektrumRCvideos

Жыл бұрын

Thanks for your feedback Andreas!

Anti first protection

Heading Hold is very dangerous. I have crashed nearly my plane using heading hold.