Spektrum Smart Receiver AS3X Setup Series #8 - Frequently Asked Questions
Join fellow RC enthusiasts John Adams and Tom Cogswell from Spektrum for answers to your frequently asked questions! Have a question that was not answered in the video? Please comment and we will answer!
- Please note - These instructions apply to setting up the AR637T, AR637TA (must be unlocked) AR630, AR631, AR8360T and AR10360T AS3X Safe receiver.
Here are some important links
AR637T - www.horizonhob...
Compatible remote receivers
SPM4651T - www.horizonhob...
SPM9747 - www.horizonhob...
Other videos in this series
Intro, Compatibility and Install - • Spektrum Smart Receive...
Binding - • Spektrum Smart Receive...
Initial Setup - • Spektrum Smart Receive...
AS3X Gain - • Spektrum Smart Receive...
Using Knob and F Modes - • Spektrum Smart Receive...
Preflight Check - • Spektrum Smart Receive...
Conclusion - • Spektrum Smart Receive...
FAQ - • Spektrum Smart Receive...
Make sure to follow us on Facebook and Instagram for all Spektrum News and Promotions!
/ spektrumrc
/ spektrum_rc
@SpektrumRC
Thanks for watching!
Пікірлер: 139
I fixed my problem of Flight Mode changes not being registered in the Forward Programming screens of DX8 Transmitter by starting a new model on the transmitter, factory reset on AR637T and reprogramming . The problems I was seeing ( in my previous comment) seems to stem from using a transmitter model previously bound to a AR636A receiver and then rebound to a AR637T and forward programmed . There appears to be some software conflict that lead to Flight Mode changes not being registered in the forward programming routines but still registering in other functions of the transmitter.... note for Spektrum software guys but nice job on getting the forward programming system out there .I like it :).
My question has been answered thank you so very much. You guys are awesome!!!
Great video series, thank you! But I miss one chapter that explains in detail all about the heading hold feature (when and how to use). And I miss another chapter that covers the trim function: some say never use any TX trim for AS3X mode and safe mode as this is interpreted as a continued stick input. In your FAQ chapter you mention that the plane can be trimmed without worry in AS3X and safe mode. Where can I get detaild information on those two topics?
Scale it down for DX6 users
Gents, Thank you for your insights and education. I'm now using my second AR637T and feel comfortable programing as desired. I am a little concerned about this second one as the throttle, when sitting in the off (pulled back, not throttle kill) position, will suddenly and momentarily bust on. I'm guessing to about 25% or so - and then it's back off again. This has happed at various times during programming and most scary, when simply orientating the plane in random positions to test Flight Modes and angle limits. My plane is electric with a smart ESC.
AWESOME THANK YOU FOR SHARING
Good video 🛩
@SpektrumRCvideos
2 жыл бұрын
Thanks 💯
Thanks for this presentation. I have a question which is - When setting the plane "level" - does this mean level as it would normally fly. I have a visionaire which is a tail dragger and so theoretically i have to lift the plane up at the tail to get the wings level - is this right? Thank you
Forward programming is great but we all don’t fly together so if I want to put a 637T in one of my models and use the same settings as my buddy (who has the same plane) 5 states over as a starting point but don’t know his trim settings or gains it was easier to use a system like the 636 SRM file. Would be nice to have this option as well and still use the PC for the 637T
@SpektrumRCvideos
4 жыл бұрын
There is a model sharing program in the works! Stay tuned :)
Hi, Although I'm new to this, I've flown on and off for decades and I find this new tech quite confusing. I have just bought an AR38360T and the manual says "Do not use open mixes for flight control surfaces when setting up a model with AR8360T for AS3X and SAFE....". My question is : what is an "open mix" as opposed to any other kind of mix ? As I'm flying an F5J glider mixes are needed to for crow braking and camber so I'm a bit stuck not knowing exactly what you mean.
How do I check that the model profile I programmed into the receiver is actually there?
How can I make small adjustments to the pitch to make plane fly level when in safe mode in forward programming?
Great informative video!
Hello On a tail dragger do you need to level the plane airframe not on the gear?
@paulballard4243
3 жыл бұрын
I’d like to know this also
A very helpful video, as is the series. I’m new to AS3X and struggling to get the gyro to respond. Is this because the Heading Gain must be greater than zero? I’ve followed the setup video and when I do the AS3X check I get no response from the plane. SAFE works fine.
@SpektrumRCvideos
Жыл бұрын
AS3X can be very hard to see on some models. It only corrects while the model is in motion, unlike safe or heading hold where it corrects until the orientation is returned to the designated point. Try watching your servo horns or surfaces VERY CLOSELY while you physically move the model. Also Safe mode is a great way to make sure the surfaces are correcting in the right direction because there is no way it will be different then the AS3X directions because in essences SAFE is built off the AS3X algorithm. Hope that helps!
I've got a DX8G1 and an AR8360T. I can't do forward programming on my transmitter to setup AS3X or SAFE. My friend has a newer transmitter, I believe a DX6E. Could we use the DX6E to setup Forward Programming>Gyro Settings to setup AS3X and SAFE on my AR8360T and could I then use my DX8G1 to fly my plane and get the benefits of AS3X and SAFE? Thanks for any help and thanks for all the great content!
@seth2055
3 жыл бұрын
I have programmed this on the d6xe but you need to have the radio updated
@brandonmathis1335
3 жыл бұрын
@@seth2055 Yes, thanks. I did go ahead and use a DX6e with latest firmware. It worked fine.
@seth2055
3 жыл бұрын
@@brandonmathis1335 That is great to hear
This goes in all my balsa planes.its like insurance.also makes u look good in the wind
hello its great you taught me how to set up AS3X, but im a bigger piolet who is used to bind and fly, I need safe to fly without destroying my plane, how do you set up safe , you stopped at that point
Hi , I received an AR637T received this week. I copied a many times flown model into a new position on my updated DX8G2. The RX in the model previously was an AR8000, but it's a very basic 4 channel plane. Here's where the issues start. I bound the AR637T to the new copy, binding was no issue, but **nothing armed. No beeps, nothing. ** I went through the AR637T setup procedure, it gets to the "receiver is rebooting message" and stays right there. I was thinking maybe after completing the basic setup procedure it would arm, but no. I did pull the plug a few times, cycled the tx etc. I put the aR8000 back in...and bound to the original copy and all works. Note...I did match the orientation the server connections old rx to new rx (ground up), then thinking ok maybe it's different, I reversed the servo connections. Still nothing. Here's the biggie I guess. Even without doing the initial setup, I expected the AR637T to act like a regular RX. Did I just get a bad one?
Great product. Owning 1 636 yet, 1 AR7350 , 2 AR 9350, you can see that I love those. Any plan to have more channels with the same technologies and features?
My iX20 will not see the AR637T receiver in my Conscendo Evolution for Forward Programing. When I go to Forward programing, the iX20 says "Navigation not found", and at the bottom of the screen, it displays in print a 9010 receiver. I have tried binding with the bind plug in the battery area of the Consendo and also using the bind button on the receiver. The results is the same. I also tried binding it to my iX12 with the same results. That tells me there is nothing wrong with the iX20 transmitter. Both transmitters have the latest updates. Either I am doing something wrong or there is a problem with the AR637T receiver in the new Consendo Evolution. Your help would be greatly appreicated. Thank you for your help with my problem.
While I understand that my DX8 G1 (which I grew up on and love) is there a way I could do the forward programming on my AR630 through my laptop? I have a newer Futaba transmitter given to me.
I'm using a DX6 with the AR637T. I have my flight modes on switch B. If I want to experiment with 3 different gains setting (ex. 15% for AIL and ELE, 25% for AIL and ELE, 35% for AIL and ELE, I'm flying a Flightline P51 850mm with no rudder) can I put those 3 different gain settings on switch D? That way I start with the lowest then see how high I could go before oscillation. If it's possible how would I do that? These videos are nice, but not everyone could afford these fancy transmitters. Just focusing on the fancy transmitters I'm sure is turning people away from the hobby.
I recently purchased two aircraft with the AR637TA receiver pre installed (BNF), and I cannot for the life of me figure out how to get the telemetry to report altitude. With the AR637T that I have used in a number of different models, I was able to go in and select telemetry, then "auto configure" and got it to work, but with the AR637TA, nope. Can I not get that metric from the AR637TA?
@SpektrumRCvideos
2 жыл бұрын
The A version for the AR637T does not have the built in hardware for the altitude sensor. Only the open stock AR637T
Good video.. I lost my E-flight 70mm Viper two days ago ! Lost it in some dark gray sky. I took a look at my time left, and when I look back to the plane, couldn't see it... I could hear it but couldn't find it back. Could the virtual fence be installed in other E-Flight airplanes ? Like in my E-Flight Viper 70mm ? Not the auto landing, but the virtual fence ! Thank you,
I installed this in an FMS Ranger. On my first flight instead of staying level, the plane kept nosing down slightly. I had to use up elevator to keep it level. Any ideas why? I noticed there's a setting in the AS3X menu that I can manually force it to pitch up. Is this what I do to correct it?
it would nice if you showed how to set up the AR637T with a DX6E. there is NO nob or slider to adjust the Gyro sensitivity. how do I set that up on a DX6E???
@choppa5300
2 жыл бұрын
You have to set to gear channel or to fixed in forward programming and it does not need to be a switch/ channel
Finished forward programming my AR637T and assigned my Mode switch to Aux 2 switch D with DX8 transmitter but the AS3x functions only show Mode 3 and don't change with the switch.The other transmitter functions DO change modes with the switch but the modes indicated in the forward programming gyro gains page doesn't indicate a mode change and is stuck on mode 3 AS3X gains don't . I did a factory reset and reprogrammed but still the same problem. Any suggestions ?
@choppa5300
2 жыл бұрын
Same issue with dx6e and ar631 had to use the gear switch 2 position
I have a ar630 spectrum reciever why dont you do a tictorial on that reciever?
@SpektrumRCvideos
3 жыл бұрын
AR630 programs the same as the AR637T :)
Do you still have the eflite inverza 280 model on sale or anyway I can get the parts ?
@SpektrumRCvideos
2 жыл бұрын
Nope
Can you use the AR637T in a Carbon Fiber aircraft as long as the antennas are out side the aircraft.
Should I use separate switches for dual rate and gyro gain? (Flight mode). The old receiver I used 3 flight modes. 1 low rate-no gyro, 2-high rate- no gyro. 3- high rate with gyro. Would this be optimal?
I have this receiver mounted in a 2.5 m glider with duel servo flaps and ailerons. I am looking for a return to home facility that can be interfaced to the receiver. Can you advise please. Many thanks Warren Massey Durban South Africa
I can’t get AS3X to work on my dx6, I followed the directions perfectly and AS3X is not working
Hi John, top explanatory videos. Does Gain, and Flight Mode need their own channels? I'm interested to know how the channels were set up on the T28 to fit in Gain and FM on the AR637T. I am hoping that Safe slots in somewhere without requiring it's own channel. Many thanks
@jetjacko
4 жыл бұрын
Hey, I kept playing with the Gains and FM, I've now got it. And yes, I watched your videos again. Looking forward to the Safe info.
Without the app, how can I download a specific BNF model profile that I want to upgrade from it’s AR636 to smart components?
Is it possible to use this reciever with a dual aileron servo and a dual elevator servo set up?
I get elevator and Aileron flutter on the AR637T when as3x first initialises and after . Don't get any flutter using it as a normal receiver
@SpektrumRCvideos
3 жыл бұрын
If you are using analog servos, go into the frame rate menu (inside forward programming) and change each channel to 22ms. That should do it
@tinusvandyk46
3 жыл бұрын
@@SpektrumRCvideos The frame rate was already set to 22ms You sent Today at 1:01 AM so no need to change.The the same aircraft works fine , (no flutter ) with its original AR6363B receiver.The AR637T works fine(no flutter) prior to first time As3X setup.The problem also goes away after I do a factory reset.The flutter occurs randomly if I test the servos from min. to max. in As3X mode You sent Today at 1:00 A You sent Today at 1
Just got Aero Scout with ar631 rx. Have DX6 with latest firmware 2.08. Go to Forward Programming-Gyro setting, BUT KEEP GETTING "CONECTION FAILED" What's wrong? Any comments appreciated.
@SpektrumRCvideos
2 жыл бұрын
Hi Geoff, you will not be able to access forward prog on that receiver until you update the receiver to V2.31 or higher. The stock firmware locks the user from making any changes via FP
@geoffsamuels3707
2 жыл бұрын
@@SpektrumRCvideos Thanks. Just heard from Horizon and they got me got me up and going - no need to access radio after all (thank god). Aero Scout manual is misleading and guy on phone agreed! Said he would bring up issue. Thanks again
Is an as3x reciver all ready programed if you buy one from a model shop ?
Hi. I slope soar in high winds here in Cornwall on the coast at St Agnes. Winds can blow up to 50 knots or more and launching can get a bit 'hairy'. I would like to use this to aid during the launch and landing. I obviously don't have a throttle. So how do I activate the stabilisation?
@SpektrumRCvideos
2 жыл бұрын
Hi Carl, great question! One of the beauties of Forward programming is the stabilization system LEARNS how your TX is setup. So if you are using a sailplane model type without a motor, it negates the need to throttle up to activate.
Can I get the measure of signal strength with this receiver?
On a tail dragger, is the plane considered level when sitting on the back wheel or does the body of the plane need to be horizontal?
@SpektrumRCvideos
3 жыл бұрын
NO, level would be considered with the tail up. Hope that helps!
I booought an as3x reciver from my model shop and i can not program it for my F15 Eagle why
Question, new PnP 5 channel + lights plane, ordered AR630. I have a DX6. Want to set up just like my BNF Cirrus w/safe select and AS3x. AS3x I keep factory settings, no adjustments on gains, and set safe envelope up either on or off. Correct?
@SpektrumRCvideos
3 жыл бұрын
The stock gains will likely do fine, but if you run into oscillations then you may need to adjust. Safe Envelope ON is correct.
Explain “forward programming” thanks
I have a dx8e radio. I have assigned the r knob to the aux3 channel for on the fly gain change(ar637T RECIEVER). But after Setting as3x and safe the knob does not change the gain. It worked briefly but then stopped. What could be wrong here? I have ensured the switch and channel assignments are right . It worked briefly for me in two flight modes but rotating the r knob does not change the gain at all. Also please note i have NOT captured gains yet.
@SpektrumRCvideos
2 жыл бұрын
IF you go into the Adjustable/Fixed Gain menu, do all 3 axis have adjustable or fixed? This is assigned per flight mode. By default it will be adjustable but this is where I would suggest checking first. Beyond that double check that you have the gain channel and knob selected in that functions perspective menu.
@ayyappa78
2 жыл бұрын
@@SpektrumRCvideos Yes they are all adjustable. I checked that multiple times. gain channel and knob is selected
@SpektrumRCvideos
2 жыл бұрын
If you go into the monitor screen on your transmitter and move the knob, do you see the channel moving with it?
@ayyappa78
2 жыл бұрын
@SpektrumRC yes checked that too. It moves perfectly from -100 to 0 to 100
@SpektrumRCvideos
2 жыл бұрын
Odd... try creating a new model and testing it? Could be corrupted data in the model file for some reason.
Do we need to add a capacitor as “brown out insurance” when using AS3X? Other gyro manufacturers have recommended this??
@SpektrumRCvideos
3 жыл бұрын
Really depends on your setup. If your BEC or RX battery is adequate then it should not be needed.
Hi, thank you for these videos, they were much needed. I have a perfectly tuned plane with the AR636 receiver, but I want to upgrade to a complete SMART eco system, including the SMART ESC, can I copy my settings from the AR636 with SAFE to the AR637 T? Also, will there be in the future another version of the AR637T with more than 6 channels? Thanks again and look forward to the rest of the videos.
@SpektrumRCvideos
4 жыл бұрын
Unfortunately there is no way to copy your settings from a 636 to the 637T at this time... Keep your eye on the Horizon for product updates :)
Wonderful presentation: Here is a question for a 'Not so experienced flyer' Most of my aircraft are Eflite because I love flying scale & mainly in SAFE. (Apprentice-Cherokee- F15-Viper-Cessna 150Z-Timber, also ump & Turbo-Male-2xConscendo's & Twin Otter + A10 64mm awaiting arrival) I do also have the FMS Yak & Avanti & would love to fly them as I do the Viper. I have tried the Admiral with Giro but no where as good as the Viper or F15 Eagle flights where I can really enjoy the experience without panicking . I did not like getting the 636 as I have one from another aircraft & would need to program it using a cable & PC, I use a mac. Am I to understand this transmitter will enable me to drop it into the FMS Yak v2 and it would control in a similar way to the Viper? or do I need to program it? I have a DX9 Keep well & safe to you all. bellairvideo
@SpektrumRCvideos
4 жыл бұрын
Bellairvideo the 637 would need to be programmed and tuned for those models but in the end you could make them fly as good as your Viper and F15 models
@Bellairvideo
4 жыл бұрын
Many thanks for your reply. I think, in hindsight, it is better to stick with my current & new Eflite models and avoid others without SAFE as a cheaper option.
3 questions questions. 1) Can heading settings be setup for leveling . The way I understand it is the gains are for transient corrections eg wind corrections. 2) IfI use 6 channel Throttle, Aileron, rudder,elevator flaps landing gear can the AR637T telemetry channel be used for the mode switch .I've been using Gear channel ( sometimes I can use flaps channel ) . 3)So the AR637T a 6 channel+Telemetry receiver but not using one of the 6 channels for telemetry ? Thanks
@SpektrumRCvideos
4 жыл бұрын
Hi John! lets see if we can answer your queries... 1) Heading Hold Gains do not self level, they simply hold the heading of the last known command. So if you pull up to a 30* angle the model will do its best to keep you in that angle until you give an input to change that heading. If you want a Self Level mode you will want to setup SAFE. 2) The 637T has 6 channel outputs BUT is listening to upto 20 channels for flight modes/gain settings. That way you can utilize all the outputs for controls on your model and then if you have a 7+ch tx you can use say AUX2 for flight modes. 3) Telemetry DOES NOT use up any channels. :) Hope that helps!
@johnpriestly6837
4 жыл бұрын
@@SpektrumRCvideos Thanks Very much that helps me immensely . I have been programming AR636 ( 4 receivers) With some good results and some challenges and your answers may be explains why I had a few crashes.I will calibrate some more. 1) One more question ,do the AR636 recievers also listen for more than 6 channels so can put flight mode on channel 7 Thanks again for your reply. Good Job Guys.. John
when i am in forward programming on my DX6 Gen 2 it will not let me work in the Gyro programming; the message "connection failed" appears. I can not explain it. What could be wrong? i saw other people having the same problem. help would be highly appreciated. thanks
@seth2055
3 жыл бұрын
Update the radio
HELLO CHAPS …. I have a question ….is the AR 630 wireless set up the same as the 637t as i am having problems with my new AR630 receiver….?
@SpektrumRCvideos
3 жыл бұрын
Hi! It does program exactly the same as the 637T. What are you having trouble with?
@biscuitbassbroom7306
3 жыл бұрын
@@SpektrumRCvideos hi thanks for getting so quick i just put it into my opterra wing wing ....i done two rang checks plus numerous aileron horizontal and vertical stabilizer checks ...i tried a flight the wing took off and did a hard left turn i tried to counter but had no responce ...i lost my opterra not salvagable ...im now putting it into an old slow flyer and ha e got most things going eccept for the motor ..i lowered the throttle atick and dropped the trim all the way down ....it worked for a few ground tests and then stopped working again ...all servos work but no throttle .can you help ? I am going to start from scratch and set to factory settings and start again my transmitter is a DX9 black
I’m using all 6 channels on my A637T . Can I still programme with my DX8 to turn on and off safe and adjust AS3X gains.? Or do I need to wait and use the new 8 ch as3x Rx
@SpektrumRCvideos
3 жыл бұрын
All our latest AS3X receivers are listening to up to 20 channels for just this purpose. So yes you will be able to use Aux2 and 3 for gain and modes. Hope that helps!
@LAFFS36
3 жыл бұрын
@@SpektrumRCvideos is there a good video that shows me this. I seem to have safe on (angle limits), not sure about AS3X. But want AS3X on, but have safe on a switch.
Is it possible to move an AR637T, with AS3X and SAFE set up, from one model to another and back again and have unique settings applicable to each model?
@SpektrumRCvideos
4 жыл бұрын
At this point there is not. Once we have a model sharing function (coming soon) then this will work. :)
@ianwilson8977
4 жыл бұрын
@@SpektrumRCvideos Thanks ... good to know it's coming; AR637Ts are in short supply in the UK at the moment. I've got one coming from Germany at the moment.
newbie question.... what safe gain values and safe angle limit should i set say an F18 jet? apparently this is a lingering question that even horizon hobby tech support cannot answer. hope you can help me with this. thanks @spektrumrc
@paulmorris563
3 жыл бұрын
SpectrumRC - nope cba answering that one!
right between chapter 3 and 4 after setting my knob the radio tells me the receiver is rebooting. why would this be?
@SpektrumRCvideos
3 жыл бұрын
The receiver must reboot to save certain settings. Let it reboot and continue
Great series of videos, nothing against Forward Programming. But it should NOT be the only option. After all this time it is clear that Spektrum has no intention of releasing PC programming or any model sharing application for their new receivers. It is not that difficult. Just there is no will to help customers.
Will it work with a JR 7202?
@SpektrumRCvideos
2 жыл бұрын
No
So I take it my DX6 is compatible with the AR637t
@SpektrumRCvideos
4 жыл бұрын
ledomengineering yes it is
For some reason, maybe me beeing stupid :), I can not as with the AR636 usage get the L Trim on my ix12 go to enough high and low values so I can get that Trim button be used for changing the AS3X gains (instead of the suggested Right knob). I only get it to go to +29 to -29 in the monitorview ?!!?, which results that I can only change the gain a little, not from 0 to 100 %.
Would this work with a heli running a microbeastx
@SpektrumRCvideos
2 жыл бұрын
No
@Mao_tse_tung
2 жыл бұрын
@@SpektrumRCvideos why not because like I said it’s in and communicating and the setup was fine. I was told several different things from tech support including that this would work. It does work so far. There is a huge lack of information and no one willing to help I’m not sure why but it has enough channels and the microbeast initialized. So why no?
@Mao_tse_tung
2 жыл бұрын
@@SpektrumRCvideos just some help would be nice other than just a no
@SpektrumRCvideos
2 жыл бұрын
@@Mao_tse_tung Sorry for the brief response. I suppose it will work if you leave it as just a receiver and do not turn on AS3X/SAFE but if you do try to run the integrated stabilization it will have a very bad affect on the Microbeast FBL. Sorry the short answer is no, it is not recommended.
@Mao_tse_tung
2 жыл бұрын
@@SpektrumRCvideos thanks I was worried for a min it’s just working as a receiver til I the fbl unit is off back order
My DX6 Gen 3 . Doesn't have a knob, so what switch can I use to adjust the gains?
@SpektrumRCvideos
3 жыл бұрын
You will need a knob/slider/trimmer for inflight gain adjustment. Otherwise, land and adjust from menu
@joenaylor34
3 жыл бұрын
@@SpektrumRCvideos Something wrong with setting up a 3 position switch to change gains in 3 steps?
@SpektrumRCvideos
3 жыл бұрын
@@joenaylor34 Nope that works well actually. Is a great way to setup a OFF switch as well (IE set gains to 0 in that mode)
@joenaylor34
3 жыл бұрын
@@SpektrumRCvideos I have the gain set on a switch of my older DX6. Question: Do I set -100, 0, +100 for the limits, or 0, 50, 100?
@SpektrumRCvideos
3 жыл бұрын
@@joenaylor34 If you set the switch as the F-mode (flight mode switch) in the channel assign menu it should do that for you essentially.
You flown for thousands of years?? Lol
I like the series however it is not clear as to actually how many channels these functions require. Figuring it takes all 6 ports for servos , how many additional channels are required to use the AS3X features. I am not really interested in Safe/Panic functions
@SpektrumRCvideos
3 жыл бұрын
It could be anywhere from 1 extra channel to 4 if you are just using and tuning as3x. 1 for flight modes, and the other 3 if you wish to have each axis to have a different channel for gain adjustments in the air. One of the great things about this system is just how versatile it is :)
@gbinno
3 жыл бұрын
@@SpektrumRCvideos So your saying i need one free channel for FM and one free channel for the adjustable gains ??....Currently using all six channels for servos
@SpektrumRCvideos
3 жыл бұрын
@@gbinno Correct, each function takes its own channel
Can this be installed in anything I build?
@SpektrumRCvideos
3 жыл бұрын
For the most part yes! If it has wings, you can use the AR637T
@martindavey8742
3 жыл бұрын
@@SpektrumRCvideos Thank you :)
Chaps. I have watched a few of your videos. I would like to see the system actually working rather than just lectures. Can you move the model around and watch the surfaces correct the attitude?, or does the plane need to be moving? I dont know these things. Tony UK
@SpektrumRCvideos
3 жыл бұрын
Hi Tony, yes you can. I also suggest taking a look at this video from HH kzread.info/dash/bejne/hGeerrd6lJjKhrA.html
Ar8020. 1to 8. Why don’t you tell what they are ?????????
@SpektrumRCvideos
2 жыл бұрын
Because those port assignments can change depending on model type and how you have the wing type selected, among a number of reasons. One great tool that helps to figure out where to plug in everything is the servo monitor screen on your transmitter. Listed from left to right, those are where you should plug in your servos etc. Hope that helps!
how to make it a Regular receiver ?
@SpektrumRCvideos
4 жыл бұрын
It is a regular receiver until you program it for as3x and safe :)
@user-yl5lp7wu2w
4 жыл бұрын
@@SpektrumRCvideos Okay, but how do you turn off the gyro at all? every time I turn on the plane I have to keep it stable before the receiver turns on.
@SpektrumRCvideos
4 жыл бұрын
@@user-yl5lp7wu2w Did it come with a model?
@user-yl5lp7wu2w
4 жыл бұрын
@@SpektrumRCvideos I bought the viper pnp that comes with the receiver.
@SpektrumRCvideos
4 жыл бұрын
@@user-yl5lp7wu2w That model should come with a AR636A/B not a AR637T. Is that what you have?
Only horizon would sell a new model transmitter with out of date firmware.. money grab or what. Maybe tell your techs that when someone asks. If they buy a new transmitter are they gonna need to update it to have all functions working like forward programming, horizon tech says nope you dont need anything to update.. then i find out i need a 50$ cable to update my new transmitter.. such a piss off..