Another question for you. When you said “I will change my serial number” 12:37 . Do you just change it to the serial number on the side of the scooter or do you pick an arbitrary serial number? Thank you for the help thus far!

@WattsnabbAB

11 ай бұрын

Its depends witch motor you have. If you have a new motor(PADH)then I use serial on the side. If its a gen 1 or 2 them i use somting like N4GSDXXXXCYYYY X is year and week ex 2330 and y is whatever number you like ex 1337

Great video, thanks ! I wonder how you aliment the controler when you try to flash it with stlink and the two cable on the front ? You talked about an adapter ? Do you know how to find this adapter ? This is for the 5v and the ground, right ? Thanks :)

@WattsnabbAB

Жыл бұрын

Thanks. Its then dashboard connector. I had a spare of them. You can also solder on the dashboard for 5v and gnd. So i connect a dashboard connector to the controller and from it connect 5v and gnd to the st link.

When I followed your previous tutorial for the 3 capacitor board with the debug terminals on the bottom and soldered them to it like you said in that video. When I click launch recovery button it says “couldn’t connect to ST-Link” any suggestion on what to do? I have verified that my solder connections are solid and not interfering with each other. Thank you!

@WattsnabbAB

11 ай бұрын

Hi. Have you checked so all connection is right and that you have installed all st link drivers properly?

@sethhubbard698

11 ай бұрын

@@WattsnabbAB just went back and verified the drivers and they weren’t correct. Fixed that and it worked! Now it’s shaking like it did near the end of your video so I’m going to try the fix you did once my android device is charged. Thank you for the response! Edit: in case anyone sees this in the future I downloaded the new drivers from the ST website STSW-LINK009. Extracted them in a folder on my desktop and told the STLINK to find the updated drivers there

@WattsnabbAB

11 ай бұрын

@@sethhubbard698 if you have the new motor you need to do same serial number as on scooter and use shfw(187) for it to work. Sometimes you need to install shfw 2 times for it to work.

Thank you for this information but I have one question. I have a nine bot G 30 I try to flash a custom firmware, and now the scooter won’t turn on long enough to connect to the Bluetooth. Turns on briefly and shuts right off so I would like to know if I do this process should I be able to fix the problem?

@WattsnabbAB

5 ай бұрын

Hi. You have used wrong firmware. Need to st link it.

Hi good explanation thanks. Can I ask you if I do that process and custom firmware it can I solve the reduced power issue after %70 battery left ?

@WattsnabbAB

9 ай бұрын

No not really but becuse you increase power you will have mord power. Best way is to buy external battery to get longer range.

Can st-link fix the issue with DRV 1.8.7 stuck at 20kmh speed and cant be downgrade through bluetooth?

@cpjhardware991

10 ай бұрын

yes

Hi, My Original G30 Max Controller has Dies as I Cant Re Flash Custom Firmware or even Stock Now. I have Been Using an External 48V Battery Pack that requires its Custom Firmware. If I was to buy any G30 Controller, will this will ST Linker Still Work? I've been told have to use a Original?

@WattsnabbAB

3 ай бұрын

You need to have costumfirmware to use 48v. So you need a controller that have that on it.

hey i cannot install reflasher can someone send me a link how to do it ?

Have a second question is it possible to ST link a high boy max scooter?

@WattsnabbAB

8 ай бұрын

Hi. Dont know :)

Dio = data input/output, to bring or get data Clk = clock, for reading the actual data Sw = switch, your blue device Good video 😃

Even with soldered on connectors I still have trouble connecting to target.😢

@WattsnabbAB

11 ай бұрын

Yeah hard to say why its so. I do many scooters here and only time i have trubble to connect is when my connection is bad.

Hi, is this now also possible with the new controller with AT chip ?

@WattsnabbAB

11 ай бұрын

Hi. Yes it is =)

Hi, i want to make with this method. Thanks for the video! What happens if i put the current serial number of my scooter on Reflasher?

@gagash3683

Жыл бұрын

Motor shaking :(

@gagash3683

Жыл бұрын

Resolved!

@WattsnabbAB

Жыл бұрын

@@gagash3683 haha did you miss it when i show its shaking on my video =)

@WattsnabbAB

Жыл бұрын

@@gagash3683 great

@WattsnabbAB

Жыл бұрын

You can use the one on the scooter.

hi, you have some good videos about electric scooters I have understood that the new (black) controller can ST-link when I select AT32.. but then I'm a little doubtful about the rest you say.. can I hack it like the others or are there limitations.. what it's about is making the animal run faster..

@WattsnabbAB

8 ай бұрын

Hi yes you can hack it like the others, you have to use shfw and not built a firmware on web. Shfw is the config tab I scooterhacking:)

@aagerasmussen107

8 ай бұрын

Hello again and thanks for your quick reply I have now done as you prescribed and ST-Link my new type of controller in MAX (G30).. I have used SHFW Regular-Base 187-v0.3.6 and tried several setups with Profiler etc. and I can only get it to work in sports mode and max 28kmh with a full battery.. if i buy one of your controllers.. is it then possible to get more speed.

@WattsnabbAB

8 ай бұрын

@aagerasmussen107 i guess you have tier pressure over 60psi. What you can do I use field weakning. Then you will get increased speed

@aagerasmussen107

8 ай бұрын

Hello again I have now set Field Weakening to the following Start Speed: 25Km/h Initial current: 3A Variable current: 400 mA/Km/h and it now runs 32 km/h thanks for the help

@WattsnabbAB

8 ай бұрын

@@aagerasmussen107 great to here you can increase it to 800 to

if i buy xiaodash with 1.7.1.13 will it be able to unlock my speed limits

@WattsnabbAB

2 ай бұрын

Hi. I don't use XiaoDash. So best is to ask them.

hi! can I come to you on a scooter and do everything in one day? As far as I understand that you are in Stockholm? What is the price for the G30P gen3?

@WattsnabbAB

3 ай бұрын

Hi. Yes sure. You can book a time here. www.wattsnabb.se/sidor/trim-g30

Where can I get the adapter so I don’t have to solder?

@WattsnabbAB

5 ай бұрын

You make it :)

Cool video, thanks from Bielefeld. Is it a special glue (or jelly) where you connect the cables to the board (I can'T fix them)? Greetings from Krautland 🙂

@WattsnabbAB

2 ай бұрын

Hi Bielefeld :) Ido you mean the Silicone in the controller? I'm unsure witch name it have but it's is Silicone.

How to ST-Link Ninebot G2E?

@WattsnabbAB

10 ай бұрын

Cant do that right now.

May I know where to connect these 5 volts and ground?

@WattsnabbAB

Ай бұрын

Yes you have it in the video :)

@user-ht5jl8mr6j

Ай бұрын

@@WattsnabbAB On the first connector I have blue, on the second black 3 red

@user-ht5jl8mr6j

Ай бұрын

@@WattsnabbAB Do I have a different controller? Or are all controllers the same?

@user-ht5jl8mr6j

Ай бұрын

@@WattsnabbAB What if I connect 5 volts to the first connector (blue) and the second connector (black) GND?

@WattsnabbAB

Ай бұрын

@@user-ht5jl8mr6j connect you dashboard cable and you Will see black and red

What program name

@WattsnabbAB

3 ай бұрын

Reflasher

Hi I can’t find the app

@WattsnabbAB

Ай бұрын

Reflasher?