Excellent tutorial, very well presented - Thank you!!

very helpful video..thanks!

Very helpful, thanks!

could be a good tutorial if the background music is turned off. The most important part, which is about reference geometry constraining should be slowly and thoroughly explained.

I thank you on the quality of work, I also have a youtube channel for beginners on solidworks, thank you again

Thank you for this tutorial. can you please upload a tutorial for modeling this contact assembly? I am having trouble with my contact assembly. I would like to try your way of modeling so that I can understand my problem. Thanks in advance

Thanks for the good video. I believe you are restricting the shear load on the U geometry, using reference plane boundary condition. If you run the simulation without that BC what will be the impact on the result?

can you please upload a video showing meshing of two tension springs. thnx in advance

Hello, could you please explain when we use the advanced fixture "use reference geometry". I always see that but i didn't understand the reason. thank you

I want to learn software background....I mean what are the applications and significance of different types of contacts.....types of mesh and its usage for different different types of geometries and all So can you please tell me any book or any material for that....? Thanks in advance

can you please tell me difference in contact set and component contact in simulation.

Mould flow analysis with Creo.....some parts practice

I was wondering if you could help. I am trying to analyse a wrench on a bolt but a pipe is over the wrench so we could get better leverage. Idk what boundary conditions I should use

@mariopersaud6703

6 жыл бұрын

It's a cheater bar like used to open a lugnut. The force is on the pipe and the wrench is in the pipe. I fixed the nut and I'm trying to analyse the forces

can you tell me if there is a penetration contact, how can we do the simulations

@kprashant0099

6 жыл бұрын

Logical Solutions how about half penetration , and which other software do you suggest for penetration and Can I have your email address please. I would like to discuss about it

@kprashant0099

6 жыл бұрын

Thank you sir. i will send you mail now

how to sync two circle example:- one circle dia75mm and secound circle dia1000mm dia1000mm (1000mm-100mm=900mm) so change dia 75mm change (75mm+100=175mm) mins i one circle dia minuse so secound dia pluse is value how create बहुत बढ़िया पर मुझे ऐसा काम कुछ इस तरीके से करना हो तो कैसे करे कृपया बताये जैसे के एक circle 75mm dia का हे और दूसरा circle 1000mm dia का हे अगर में इन दोनों में से किसी की भी साइज़ बदलता हु तो वो एक दुसरे में pluse minus खुद्ब्खुद हो जाये जैसे के अगर में 75 mm dia में 25 mm जोड़ता हु तो वो dia 100mm हो गया पर जो दूसरा dia जो 1000 mm का हे वो 975mm खुद्ब्खुद हो जाये बस ऐसे कोई भी एक dia अगर pluse होता हे तो दूसरा dia खुद्ब्खुद minuse हो जाना चाहिए और कोई भी एक dia minuse होता हे तो दूसरा dia खुद्ब्खुद pluse हो जाना चाहिए हा पर जितना हम pluse या minuse करते हे उतना ही value एक दुसरे dia में pluse minuse होना चाहिए कृपया करके ये बताये ये कैसे हो सकता हे solidwork में ?

Where you want to go? Too slow, btw nice input. Thanks

Get a lapel microphone!

Wow, you are going too slow.... maybe should go some faster...

@lawlerzwtf

5 жыл бұрын

hahahaha I don't think he got the joke