Hello all, Welcome to the channel, In this video I talked about how to mesh the component which is not meshing the 1st time, Here I used a mesh control for meshing again that single component that is failing to mesh, also share the method of how to apply mesh control.
If you are using a mesh control and still not getting the mesh then you need to check if your component is an imported file or made in Solidworks or not if you have an imported file like (.x_t, step, etc) and you saved that file to solidworks part file that is ok but that file has complex shape and geometry than you need to make that component within in Solidworks.
The second way I used " make rigid " option, If you know that your un mesh component will not fail during simulation that time you can use this option that is "make Rigid" If you use this option It means Solidworks assumes that the selected component will not fail during the simulation when you make rigid then you need to again make mesh-like standard or curve etc. After meshing you will see that component that you chose for Rigid also meshed with your standard mesh very easily, After you run the study you will get that rigid component with the Gray color so that you can identify easily the rigid component.
Here are more simulation tutorials links below
Exploring Different Mesh Types and Options in SolidWorks Simulation | Solidworks simulation
• Exploring Different Me...
Creating Remote Loads in SolidWorks: A Step-by-Step Tutorial
• Creating Remote Loads ...
Bearing Load Simulation in Solidworks
• Bearing Load Simulatio...
Propeller Simulation in solidworks | Centrifugal Simulation
• Propeller Simulation i...
Frequency simulation Solidworks
• Frequency simulation S...
Solidworks car crash simulation
• Solidworks car crash s...
Bearing analysis Solidworks | Solidworks simulation
• Bearing analysis Solid...
Solidworks simulation | Safe analysis
• Solidworks simulation ...
axi symmetric simulation in Solidworks | Solidworks simulation
• axi symmetric simulati...
How to use 2d simplification in Solidworks simulation | Solidworks simulation
• How to use 2d simplifi...
How to put the load on any particular area in Solidworks | point load | Solidworks simulation
• How to put the load on...
Perform a fatigue analysis in Solidworks | Solidworks simulation
• Perform a fatigue anal...
Performing buckling analysis on Solidworks | Solidworks simulation
• Performing buckling an...
Solidworks simulation | How to apply Remote load/mass on Solidworks
• Solidworks simulation ...
Solidworks simulation | How to make Design study on Solidworks
• Solidworks simulation ...
Solidworks simulation | Topology optimization study on Solidworks
• Solidworks simulation ...
Solidworks simulation | How to generate simulation report on Solidworks
• Solidworks simulation ...
Solidworks simulation | Bearing Load Simulation On Solidworks
• Solidworks simulation ...
Solidworks simulation | How to make centrifugal simulation on Solidworks
• Solidworks simulation ...
Solidworks simulation | Pressure vessel testing in Solidworks
• Solidworks simulation ...
Solidworks simulation | Thermal simulation on solidworks | Transient
• Solidworks simulation ...
Solidworks simulation | How to make Thermal simulation on Solidworks
• Solidworks simulation ...
Solidworks simulation | How to make Gravity simulation in Solidworks
• Solidworks simulation ...
Solidworks simulation | How to make Torque simulation in Solidworks
• Solidworks simulation ...
Solidworks simulation | How to make drop test in Solidworks | FLEXIBLE TARGET
• Solidworks simulation ...
Solidworks Simulation | How to make DROP TEST in Solidworks | use of Velocity
• Solidworks Simulation ...
Solidworks simulation | How to find drop test in Solidworks | use of gravity
• Solidworks simulation ...
Solidworks Simulation | How to find FACTOR OF SAFETY in Solidworks | use of Gravity
• Solidworks Simulation ...
Solidworks Simulation | How to do compressive test in Solidworks
• Solidworks Simulation ...
Solidworks Simulation | Tensile test simulation in solidworks
• Solidworks Simulation ...
LIKE, SHARE, AND SUBSCRIBE TO THE CHANNEL
Thank you.
#SolidWorksSimulation
#MeshErrors
#SimulationTroubleshooting
#SimulationMesh
#FEA
#EngineeringAnalysis
#FiniteElementAnalysis
#MeshOptimization
#MeshingTips
#SimulationErrors
#SolidWorksTips
#SolidWorksSimulationErrors
#SimulationMeshErrors
#SolidWorksFEAErrors
#SimulationTroubleshooting
#CADSimulationProblems
#SolidWorksMeshingIssues
#FEAErrorAnalysis
#SimulationValidationErrors
#SolidWorksMeshOptimization
#MeshDistortion
#SolidWorksSimulationProblems
#SimulationConvergenceIssues
#FEAMeshErrors
#SolidWorksMeshAnalysis
#SimulationErrorResolution
#SolidWorksFEAChallenges
#SimulationMeshQuality#analysis