I said @10:05 that I didn't use it for a few days and it's also mentioned in some of the other comments. I think I'm a bright enough person to understand the risks and rewards of making something like this. You run the same risks with the dehydrators you can buy at a store, made in a foreign place with mystery plastics, or buying your food at a grocery store where you have no clue where it really comes from or how it was processed. Thanks for your concerns.

Great video instruction and great design, and thanks for pointing out key ideas like reversing the drill for the acrylic, third wheel, and the goof about accounting for the size of the acrylic sheet stock size. Kudos!

so far we've done apples, peaches, banana, and tomatoes. On a good weekend, It can be done in a day, but I usually leave it in for two days. We just leave it in overnight....so far no critters have bothered it.

Me gusto mucho tu deshidratador, voy a implementarlo en una escuela en México y de los que he visto la tuya es la mejor idea!! Gracias!!!

im always looking for new projects, and this is the first video ive seen on solar dehydrators, honestly the thought never crossed my mind. excellent video!!! wish i could give it more than 1 thumbs up.

i wind up watching this every couple years... best diy dehydrator I've seen. well done!

@Bigelowbrook

4 жыл бұрын

thanks! And it's still working.

This looks like the best design of all I've researched, so far. (I built 4 2 foot square 'Walker Solar Dehydrators' that I've found unwieldy to move and difficult to fill/empty.) You've thought of every 'problem' I've considered. Except how to store the behemoth when not using it! :) Thanks.

@Bigelowbrook

9 жыл бұрын

+Laura Roth Yeah, I just let it sit outside. It's is a bit too large and I wish I had made it smaller.

We get a lot of cloudy/rainy days here too. I just keep an eye on the forecast and wait to use it until there are going to be a couple of nice sunny days.

Great idea. You gotta love someone who will share his ideas warts and all. I was beginning to think I was the only one who made mistakes.

So I've been spending quite some time constructing my first Downdraft Dehydrator to dry leaves (for tea and medicine), fruits and vegetables (for preservation), and seeds and nuts for small-scale oil extraction, and I am finally finished. I ran a few tests which started yesterday, and today I found out that the roof over the chimney (the highest point on the device) was affecting the internal temperature. I am currently reconstructing the chimney (making it a bit higher and adding a different type of roof) so that the internal temperature can be stabilized during this heat wave affecting the island of Jamaica. I got internal temperatures between 35.5 (95.9 F) and 49.8 (121.28 F) degrees Celsius today (you only need 40 oC (104 F) to adequately dry plant materials and preserve nutrients). Planning to get it all sorted out tomorrow. This is a modified version ( scaled it down by 50%) of the one you built.

@benedictlego6642

8 жыл бұрын

+Dwight Rose Wow this is great just a few modifications and we can get 33 to 37 degrees Celsius right? Can we use it to dehumidify our honey? Thanks

Love it! That gave me some ideas for one of my own that I plan to base on a repurposed RV refrigerator.

I was looking for solar dehydrator videos over the last few days and could not find a single decent one. I should have known that I can always rely on you. Thanks for sharing.

It seems to vent well on it's own. A few days over the summer it got a bit hotter than I wanted so some kind of thermostat & fan would help to keep the temperature more consistent.

Thank you for the plans. I see it holds 5 trays of different sizes. Would like to make one with more trays.

I seriously liked your design - good job!

nie ma to jak opary olejnej farby :D Aż miło i smacznie...

The best dehydrator and the one which make most sense of all I wave watched. thanks

Even though it works well with the air flow, on a hot summer day, it can get too hot so I may put on a smaller solar panel with a fan on a thermostat.

Man that sure does seem like a lot of work. That said, anyone that would complain about the time that this project takes to complete wouldn't be watching this video anyway. They would go to the store buying heavily processed foods then back on the couch for another round of Idol, Got Talent or some reality show, where nothing is what it seems. If there's anyone that deserves to win of all three of these shows and there are plenty all over the Internet, just like you, it's people willing to open source their projects to assist everyone. The money that you make from advertising comes from the pocket of the people who can afford this luxury, leaving the average Joe with some neat weekend projects to do into the bargain. Keep up the great work and we'll keep watching giving credit where credit is most certainly due.

I am loving your guys channel!! Great work!! so informative and easy and FRUGAL!! yeah!

Your explanation is so perfect and you experience to teach is awesome thank for you video and congrats for you channel Addy

That was an ambitious project, made even more so by the decision to video the process. Glad that you did! Thanks. :)

very nice design, a little to complicated for my building skills, but love this one....!!

Nice build Rob.. Cheers :)

Nice job! And, a thoughtful presentation!

awesome build! Once i get my backyard orchard going, i'll be building something like this. With all the crops/fruit trees you have, have you ever built a root cellar? I'd love to - i'll need a place to store crops that we don't eat/can right away.

Fabulous! A very clever designed dehydrator! Gave me some great ideas to build my own! I am wondering, because I live high up north if this wil work there also?! Thank you for sharing this. Warm greeting

Yes you did explain it properly, very well. Thank you for the pointers, I'll probably build a small version (one that can go on the back deck) and make a video of it when I do. Thanks again! ~Wayne

A great job keep up the good and industriously creative ideas that lead to these projects and videos...

Great project! I’m going to have to build one now! Oh… Thanks for adding music to this video! The music makes it!! LOL!!

El video excelente, muy didáctico, fácil de construir, una sugerencia al colector solar si le realizas un par de orificios de 1/2" a 1" para que entre aire forzado y en la parte de arriba colocarle una chimenea de tubo ya sea pvc, metálico de unos 30 centímetros el diámetro el doble de los dos orificios inferiores o un 70%, además debes aprovechar más el espacio, apenas note dos bandejas, puedes hacerlas a todo lo hancho del cuerpo del deshidratador, me gustó tú modelo de deshidratador. Gracias mano.

I let this unit "cook" in the sun for a week or so before using it so it was fairly well aired out before using it (I'm not saying this is perfect answer, but there were no noticeable odors from it.) I still rather risk using this than buying some of the mystery food from the grocery store.

Hi! I'm wondering how well the lower corner closest to the intake fares. I don't have any experience whith this kind of dryer, but min intuition makes me think that the ventilation wouldn't be as good there. I'm thinking that its to far from the exhaust for the draft to want to take that way. Have you noticed a difference in preformance? p.s. I'm planning to build a dryer of my own, so I try to collect as much data as possible before I start. Regards, Hugo

Beautiful work, thanks for sharing.

Good job. Did you try to see what kind of temperatures you are getting in it?

If you have some time I would love to hear your experience on the use of this dehydrator. Like what works with it, what does not? Do you leave the food inside overnight or take it in?

Very nice work....Thanks for sharing your ideas.....You did a great job on it......

Interesting! I have seen some models where the heat is drawn in from the top and pushed out through the bottom, reasons were because apparently the reverse method lets more humidity inside the unit. is there any truth to this?

is this possible to dry fish, or aquatic products

well illustrated and good background music 👍

the black color on the woods and the wire is suitable? will it cause any fumes that affect the food that is to be dried?

Good job and lots of great tips. Thanks

Other than stainless mesh what would you suggest after having tested your unit? Nice work, I enjoy your channel.

Very cool brother! I've been wanting to build a small solar food dehydrator myself so this was a timely video. Would you make any design changes or would you build it just like this again? Thanks in advance, Wayne

wonder if i have a dehydrator reciepe for loose leaf CBD teas?

wonderful craftsmanship!

well done!!!

I would probably just have the air intake come in through the end. Also make the shelves a couple of inches narrower than the dehydrator so you can get the air flow to go over everything properly. I push one shelf in all the way, then the next one is against the door. You sort of get a zig-zag air flow going through it instead of just through the screening. (not sure if I explained that right!)

Excellent video , very helpful. Thank you for sharing

Nice system, I would splurge and get the stainless steel screen. Not sure if the fiberglass would stick and get fibers stuck on the food.

A trick to making the screen tight is to place two shelves next to each other on the long side. Staple the screen to the outside long edge with screen moulding. Slide a 2x4 under the outside edge of the opposite shelf and then staple the screen to the frame. Now remove the 2x4 and the screen will stretch tight. Staple screen moulding over the remaining edges then cut the cloth between frames.

how hot does it get where you live and how much did this project cost and how long did it take to make

This was great! Thanks for sharing it.

Great job.Do you think a small solar powered auto air vent could fasten the process?

Love the design but for some reason when the plans come up, it's way too blurred to see the dimensions. Is there anywhere else that you have the dimensions posted?

Fabulous and informative how-to video.

Nice job. Have you determined what your temperature range is that it can achieve?

nice work, can you post a video explaining how the air flows?

How much cost it takes??? Wonderful idea on dehydration method..

Amazing. Great job!!!. Thank you for sharing

Thank you very much for your information.

I need to ask you again on your experience. I completed mine - more modest version - just a few days ago and filled it with food which is growing in the garden at the moment: cherry, greengage, peach. I left it there for 4 days (I was out of town). When I got back I noticed that everything is dry, but the peaches (not all) have moulds. I installed a thermometer which measures the temperature at the top. It goes up-to 60C (140F) in sunny days. What could be the problem? Not enough airflow?

@Bigelowbrook

10 жыл бұрын

you may be cutting the peaches too thick. 3/16 of an inch is more than enough. They should be dry in one good sunny day. If not, try to increase your air flow, but you still need to make sure it's hot enough in there.

I wonder how good it works for Cron!

Great instructions! Thank you.

best solar dehydrator on youtube.

I've putting in a root cellar but have been too busy with my other 1000's of projects. ;-)

Hi! Could you tell me How many pounds of food can it bear? Also, how much did it cost you at the time?

It's gone over 160 which is a bit too hot for dehydrating. Most of teh time it's around the 130-140 range.

How does the ambient humidity affect drying? I live in the other corner of the states where we have many rainy or cloudy days.

Several drhydrator video's show large cumbersome units. Yours takes the prize for a compact design. I'll build one over the winter.

Can this drier be used for drying grains?

Nice job !

Which is better up draft or down draft solar dehydrator?

I suppose the air heater "slope" insides could be reflective... apart the black steel meshes, of course. And the "glass" could be screened so, that it lets the sun rays in, but not so much out. Rays get in, get scattered, don't get out (much). More heat, which hen creates more draft (air circulation).

Did you taste or smell any spray paint in fruits after drying? How long paint dried before first food load?

nice work

Exelent friend !! I like it.. over all the piano ..!!! jajaj just kiding

I'm not sure...I think they have to be done at a warmer temp.

you didn't mention to consider using nontoxic materials/paint as well as netting w/o plasticizer. could really matter at this long exposure at this temperatures.

I let it set out in the sun for about a week before using it. I didn't notice any smells or tastes that were odd....even so, it's still probably safer than food from a store. ;-)

really easy instructions....thank you...

Perfect music!

Good project thanks

could you use it as a smoker as well with the addition of a small hot plate in the bottom?

@HostileHST

10 жыл бұрын

Might catch the whole thing on fire, but your food would be smoked 100% lol. Still, that is a good question. Sure would be a nice smoker if you could.

Thank you boss!

As hot air is going up, the entrance has to be in the bottom, like this the air circles constantly through the shelfs without a hot spot and goes through the chimney.

Mmm Urea-formaldehyde flavored fruit, yummy!

@Bigelowbrook

10 жыл бұрын

Did you ever consider that they do manufacture formaldehyde-free plywood? I'm sure the paint isn't the greatest, but once it's cured, it's very stable. I let this thing back out in the sun for a few weeks before using it.

@psuemor1651

7 жыл бұрын

You use too much plastic based products or whatever, paint, glue, what they use to cure the plywood, all of that isn't thought to be in contact with food much less in an oven, even if it is a low temperature one, they will free harmful chemicals into the dried fruit, that might not get you sick right away but in the long term, or to the fetus of a pregnant lady, the design is fine but you should use inert materials when dealing with food.

@stephenverchinski9967

6 жыл бұрын

P Suemor seems like a great startup business to rework the glues etc. Just recalled that the industrial dairy industry also brings us crib death and Elmers Glue? do not want that use either.

spray racks with a little vegetable oil for pain free produce removal when they are dry

Thank you. Very good

Curious about your feelings and/or opinion of the screening you used for your drying trays. Is there any issues in your mind about the screen being food grade? Can regular screen wire, synthetic or aluminum, be harmful? Being the neighborhood scrapper I have quite a few yards of both. Seems I remember reading once that regular screen wire that is not made for this application can transfer toxins, etc. Not picking on anything you've done, just concerned. Great design. Thanks for sharing it.

@Bigelowbrook

8 жыл бұрын

I'm sure you should use stainless steel, but it's insanely expensive. I have two types in here. One is nice and thin, but the food sticks to it. It might have some fiberglass material in it but it's hard to tell, the other is a thicker weave and i think it's nylon. It works far better and very little sticks to it. I don't think they off-gas anything, but really don't know. It doesn't get so hot where it would melt. I did leave the whole thing out in the sun for a few weeks before using it so everything could "cook" off.

How did you decide which materials to use for your screens? I have read that some materials can be toxic or can not withstand the heat or sag after heated up.

@Bigelowbrook

9 жыл бұрын

some of these are nylon and some are fiberglass. I wanted to use stainless but it was too expensive. Neither types have sagged.

Gracias desde Chile 🇨🇱🇨🇱🇨🇱👍

Hello Rob, Great presentation. I would love to know if this is suitable during the rainy season because I believe that’s when the most post harvest losses are experienced. I did a similar project with a little moderation to this and I’m sincerely looking for ways to improve the equipment for more better results especially in the drying time frame and seasonal usage. Thank you

Looking to make one for myself

Here’s a solar food dehydrator that I made up a few months ago. We’ve done peaches, apples, bananas, and tomatoes with success! kzread.info/dash/bejne/aox9po-nqLibe5M.html

Well done and eco-friendly

@SennaContreras

10 жыл бұрын

Perfect voor appelschijfjes Opa!

whats the cats name? I have an identical fulla called Alfie

Good point. So far, it hasn't been a problem. Maybe the cats are helping with that!

In which state are you living. Being in Maine I'm wondering if this would work as temperature drops at night even in summer...

@Bigelowbrook

5 жыл бұрын

I'm in CT. It hasn't been a problem keeping things in it over night.

could you make beef jerky with this set up?