SmartClean Philips JC5301 disassembly and repair
This video will help you easily repair a Philips Smart Clean Station (or similar) with the most common failure (from personal experience) of a non-working pump.
Personal recommendation for using this device:
1. Shave only after washing your face.
2. The skin should be dry and fat free
3. After each use of the razor, it is necessary to lift the knife cartridge to shake out the “wool”. Washing under running, hot, warm water is possible (if possible, dry well)
4. After 4-5 shaving processes or after the “wash” icon appears on the razor, put it on the station to clean it after washing it in running water and shaking out the remaining drops.
5. Carry out washing at the same time as charging the shaver.
Prolonged non-use of Smart clean, in the presence of dirt near the motor shaft, leads to its drying and blocking the rotation of the shaft.
The signal at the station will clean in the form of circular arrows indicates the absence of liquid in the cartridge. In extreme cases, you can add a little water. This sign may disappear after the system is closed again.
After installing the razor on the base and after pressing the start button, the washing process takes place with the movement of the washing liquid and the periodic switching on of the razor motor. Next comes the drying process.
Sorry for the long video. No experience.
Пікірлер: 38
Thank you for your video. I wasn't able to understand what you were saying as I am English but your video showed me enough to take apart my smart clean and fix the fault. Thank you.
Great detailed video. I had the same issue where fan/motor wasn't working which didn't push cleaner fluid up into the cleaning well. When viewing this video, for the English (85%) translation, turn on "CC" - closed caption. In settings, youtube auto-selected Russian. Then select English for translation. Also, it will make this repair a lot easier if you pop out the base. Simply lower and close the device. Aim bottom to ground about 1 meter up. Press release button and the springs will push out the bottom. To test if the fan/motor is the culprit, simply use a micro screwdriver to move the fan blades. I had an unexpected level of resistance when I tested mine. When prying off top cover, aim down. It happened in the video and to me. The cover went flying, along with the ring. Underneath the fan, there was a level of "gunk" that collected after a ton of washes of my shaver. The video illustrates methods to thorughly clean all that gunk out. After I fully cleaned the motor and fan and reassembled my unit, the repair was a success. I now have a fully functional cleaner again! I saved myself at least $75 US which is the cost of a brand new one. Thank you for this video.
@kscrib1
8 ай бұрын
Thanks for the translation hint. That made this much more useful. I had refilled an old fluid tank with white vinegar and installed that into the cleaner. I let my set for several days in hopes it would free up any gung. I did that before I found this video. My resolution was to just spin the motor/fan through the housing with a small screw driver . I did not have to remove the motor. After that, it all works great. Once the fluid pump was working again I ran several cleaning cycles with the white vinegar in the tank, just to clean any of the small holes in the system.
@paulwood7342
Ай бұрын
I am very happy. Sorry for the late response. Enabled subtitles in English for other clients.
@paulwood7342
Ай бұрын
@@kscrib1 This is another patent to solve the problem. Thank you. Well done!
Спасибо за подробный разбор. Мне помог разбор и обслуживания помпы. Подклинивало помпу.
Доброго дня! Огромное спасибо за видео. Совсем недавно произошла поломка двигателя (время пришло). Пять лет безупречной работы. Заказал в Ali Express новый двигатель. Ремонт прошёл успешно. Спасибо.
@user-rk8ip1qs9z
Жыл бұрын
Подскажите какой мотор, ссылка в идеале будет.
@Maaver1ck
8 ай бұрын
Тоже интересно, подобрал кто-то двигатель
@paulwood7342
Ай бұрын
В большинстве случаев в моторе нечему ломаться. Принцип его работы как у аквариумного фильтра . Он просто клинит от мусора. На англиском чел предлагает просто прокрутить лопасти и пропустить через систему уксус или уксусную кислоту. И это ему помогло. Не спешите тратить денгьги!
Thanks! Was able to repair a similar model with the same issue with the motor all gunked up. After cleaning it and adding some lubrification, it worked perfectly.
@paulwood7342
Ай бұрын
Sorry for the late reply. Enabled subtitles in English. Thank you.
Спасибо за уникальную видео инструкцию! Помогло!
Excellant video, any technician or handiman can understand without translation. I discovered the motor shaft was broken. ευχαριστώ
@paulwood7342
Ай бұрын
I am very happy. Sorry for the late response. Enabled subtitles in English for other clients.
Thanks! My pump motor had almost seized, too. I couldn't get the motor out as the top clip was plastic welded on, but I could remove the propellor on the other end and I sprayed isoclean / lubricant into the shaft and hand turned it until it freed up. Obviously a poor design and definitely designed not to be fixed.
Доброго времени суток, спасибо за видео у меня произошла проблема ,просмотрев ваше видео я решил эту проблему сейчас мой так скажем аппарат промывает без проблем, ещё раз хочу вам сказать огромное спасибо, и с Наступающим Новым Годом удачи вам везде и во всём.
@paulwood7342
Ай бұрын
Спасибо за теплые слова и извини те за задержку в ответе. Я рад.
It’s a shame you haven’t added subtitles in English. I have one of these to repair and I’m just about managing to understand.
@paulwood7342
Ай бұрын
Sorry for the late reply. Enabled subtitles in English. Thank you.
День добрый. Имею так же похожую станцию. Но у меня сгорел моторчий ( прогнил) я его заменил на такой же. Но теперь появилась проблема что станция набирает жидкость для чистки и в момент когда должна включиться бритва она выдает ошибку о загрезнении. Не могу приложить голову в чем может быть проблема
Можно у вас купить двигатель на замену?
What size is the torx screwdriver's bit?
@HazeBaze
Жыл бұрын
i used the TORX T9H of ifixit
Подскажите пожалуйста какая маркировка двигателя,и на сколько Вольт. Есть варианты от 4.5 до 12 Вольт,с длиной рабочего штока от 7 до 12 мм.
@Maaver1ck
8 ай бұрын
Подобрали двигатель?
@paulwood7342
Ай бұрын
Извините. Нет понятия. Не думаю что актуально заниматься заменой двигателя если нет донора.
Извените, а не подскажите в чем может быть проблема, после замены двигателя во время чистки загораються все индикаторы и он перестает чистить. Тоесть 2 раза набирает воду, не активирует бритву и выдает ошибку
@paulwood7342
Ай бұрын
Извините за запоздалую реакцию. Есть ли заряд у бритвы? подходит ли модель бритвы к базе? Не исключено что делов насосе или в микросхеме. Во втором случае- на мусорку.
Подскажите какой мотор у этих моек.
@Maaver1ck
8 ай бұрын
Подобрали двигатель?
Моторчик сразу в руках оказался? Он просто вытаскивается. Или надо что-то открутить?
@user-bb3ve5fk7z
Жыл бұрын
До моторчика нужно добраться. Ничего не нужно откручивать. Его фиксирует сверху защёлка,внизу колпачок. Посмотри внимательно видео. Довольно подробно и понятно.
@user-fi6lr4ce5c
Жыл бұрын
@@user-bb3ve5fk7z спасибо вам. Всё получилось.
Здравствуйте ,не сливает житклсть в чем может быть проблема?
@paulwood7342
Ай бұрын
т.е насос работает наполняется емкость и течет наружу?
Need English
@kscrib1
8 ай бұрын
See the comment above from @edwardpascua4807