SMALLEST Production V-TWIN Knucklehead Engine!
Ғылым және технология
Get the engine here:
► R29 v2 engine ➜ bit.ly/3ghGGiP
►Other v twin engine ➜ bit.ly/3XlGb8m
►best Gift Ideas for Gearheads ➜ bit.ly/3ETjwYB
►10 Must-have Engine Gift Guide ➜ bit.ly/3TJDwCb
------------------------------------------------------------------------
►Subscribe! bit.ly/2m1d1y7
►Instagram: johnnyq_90
►Support my videos!: / johnnyq90
Пікірлер: 472
Rc motorcycle might be too hard to drive but RC morgan 3 wheeler with this engine would be awesome.
@Pyro60000
Жыл бұрын
A trike might be a good compromise.
@yoyocheqc301
Жыл бұрын
A mf honda bigred
@MrAlexman37
Жыл бұрын
Yup! Made in wood, like the real one! Can be awesome
@Dymitr_Nawrocki
Жыл бұрын
@@Pyro60000 A harley with sidecar would be nice too, and battery, radio receiver and other "ugly" stuff could be hidden in sidecar.
@ethanspaziani1070
Жыл бұрын
I had an RC motorcycle it was pretty easy to drive just had to get it going
That idle RPM is amazing for such a small engine! This sounds incredible too
@waynejones6144
Жыл бұрын
The low idle is caused by the large flywheel that is on the primary side that is being used to start and run it.
I love the little spark plug and spark plug boots too cute! This could make for an amusing generator for lipo packs.
@aU_tHe_sLaYeR
Жыл бұрын
Put those into your.......🤣🤣🤣🤣
Most incredible is how closely this model engine follows the real knucklehead engine in is construction details. I worked on an Arlen Ness blown 93 inch knucklehead from 77 to 80, as a young Marine stationed in Hawaii, and have worked on such fifty years now. That is incredibly accurate sounding to a full scale "knucklehead". This is a fine follow on to the very accurate panhead engine that's been available for some time, thanks for showcasing this for all of us.
@genefogarty5395
Жыл бұрын
Wow, a 93 inch knuck back then must've been something else, especially with a blower. I had an EL replica with a "93 S&S about ten years ago and it was real fun to ride. Took a lot of people by surprise. I loved the old builders, Hunziker, Ness, Denver and Ernie Johnson were my idols as a kid. I still have the Black Gold blown 750 Honda poster that hung in my bedroom when I was a kid, those rectangular exhaust pipes were sick!
@johnmcclain3887
Жыл бұрын
@@genefogarty5395 I rode that Ness blown knuckle for a couple years, couldn't keep it running, constantly stuck the front exhaust valve. I didn't realize at the time, I could simply make exhaust guides I couldn't buy at the time. I "nursed it" prepping it for a run, and knowing it would get ten or fifteen miles and need the valve redone. I saw the bike again and again for twenty five or thirty years. Never came close to "topping it out", way too much power for the chassis.
@johnmcclain3887
Жыл бұрын
@@genefogarty5395 I looked at those SS engines, never could afford to buy one, but built a few. I've got a 103 STD Panhead, going back together for this summer, I'm considering reducing it to 88, for better life. Been doing an 88 since 95, for a street engine.
@genefogarty5395
Жыл бұрын
@@johnmcclain3887 The EL was one I couldn't pass up, got it from a guy going through a divorce for less than the price of just the engine. He was done with bikes so I got all his stuff for one price. Sounds like that pan will be a stout runner, best of luck with her!
This sounds so refined. Definitely a favorite.
Wow 3 videos a row keep this up man! ❤
"Who is a big boy!? Who is a great big boy!?"😹 This lil engine is so cool!
This is awesome! The timing sounds the same ! Very impressive.👍🏻
Awesome little engine! Great work!!😃👍🛠️🔧
most beautiful work I've seen in a while. Dude.
That thing sounds incredible!
Try advancing the ignition timing to see if the running improves
@vipervidsgamingplus5723
Жыл бұрын
Maybe having it break in properly would make a difference. It's not like any engine runs perfectly before break in.
@edjunker
Жыл бұрын
Might try running it on petrol as well.
@8180634
Жыл бұрын
The real Harley sounds pretty much just that bad, so if the goal is to model after the real thing then they nailed it 100%. It's characteristic of the design I think.
@ferrumignis
Жыл бұрын
@@8180634 Like the Harley, the design has been optimised to convert fuel into noise without the side effect of mechanical power. 😁
@MarkPalmer1000
Жыл бұрын
It needs to break in, do not go adjustment happy with these engines. Harley engines have a loping idle by nature, this is made to duplicate the characteristics of the 45 degree Harley V-twin.
I've been looking at these all year and am amazed at how much they sound (in scale) to the actual Knucklehead. Very curious to hear the Shovelhead!! The old Harley engines have such a unique sound, the manufacturer of these scale engines is really on to something.
@daniellibich1376
9 ай бұрын
With the few known they were looking all over for a miniature motorcycle engine as if the quality of details of a miniature knuckle-head to the real McCoy as if the idle sounds like a real knuckle-head as later Harley Davidson famous V-twins has the few know they want to get their hands on a miniature pan-head and compare it to a real pan-head.
Gorgeous little engine 👍 love the sound 👍
Wow that’s sick man great job 👍
The very first top end rebuild I ever did on a Harley was on a 1947 knucklehead. This is pretty damn cool!
My buddy had had a 1963 knucklehead police trike, great rc idea!
I subscribed to your channel a few weeks ago, and today (Dec 4) I have completely watched EVERY single videos you put out as of now. Might I suggest that you put out one video showing a real-time machining on the lathe and the CNC mill please? I love those kind of things. :)
@alanhardy3374
Жыл бұрын
Right on dude Would be fantastic
@genefogarty5395
Жыл бұрын
They're mass produced, Stirling makes these for 900 bucks a pop.
What a perfection!please make a 2x1 exaust!
That idle is amazing. I need this as an alarm clock ! 🤣 with revving !
@rsharney1111
Жыл бұрын
Thats a damn good idea! I know a million harley guys would love it.
@liamgleason3416
Жыл бұрын
I loved this idea until I realized that you would be making essentially a time bomb 😂
@Shadow0fd3ath24
Жыл бұрын
Just cut this videos audio out and play it through a speaker lol
@Jason-gj1pu
Жыл бұрын
Make it run on wild Turkey and go to bed with the fumes,.
@koollee
Жыл бұрын
Lol
The definition of form and function Sooo nice 👌
Crazy how accurate it sounds too, just in smaller scale of course.
Okay, that's adorable- I think this one needs to go into an r/c boat hull...
Yep sounds like the knuckle s i use to build. Great job...
I really can't believe the amount of hard work and engineering that go into these little engines. 👍
@mickmuzzmkmz1628
Жыл бұрын
You'll believe it when you see the price! 😄
@johnkilo3
Жыл бұрын
@@mickmuzzmkmz1628 for real, $900 for this little thing
@MarkPalmer1000
Жыл бұрын
@@johnkilo3 They typically sell at auction on E-Bay for $450-550.00.
@gazratjackson
Жыл бұрын
@@MarkPalmer1000 exactly, I just paid us$388 or 580 Australian, big bucks for a toy but don't care, by it now is au$1350
That is so cool, my favorite so far
That's one of my favorite Harley engines. Soooo cool
Trop trop fort !!! Magnifique, j'adore !! Bravo !!!
It’s funny seeing you grab the flywheel and giving it a spin to start it.
Magnifique, c’est de l’horlogerie, félicitations
sounds mad 🔥
sounds amazing !
Sounds like it has about the same power as a real Harley engine. The idle speed is really impressive for such a small motor though
@adamr9215
Жыл бұрын
The heavy flywheel helps with the idle quite a bit. If it didn’t have that big chunk on it, I’m sure it wouldn’t idle so low.
@ferrumignis
Жыл бұрын
_"Sounds like it has about the same power as a real Harley engine"_ Don't be rude to the model engine.
Wish I had this in the 60s,my G.i Joe would have a great scooter..great job man.
That's a really beautiful engine ☺️
Wow,that was just TOO COOL!!! Loved watching every part of this one!!! : >)
I'm very impressed with this motor
I bet you could make a pretty sweet reverse trike with that! Exposed engine would look sweet!
A Work of Art!!!
was für ein cooler Sound !
Awesome sound, the best of all the tiny engines I've seen on your channel so far!!! Might be even better if 4 of them would be combined to build a V8 😏😎
@borttorbbq2556
Жыл бұрын
Even better if you can take about 16 of them depending on if the angles right and if it's set up properly you could make a plane what do you think the Harley engine is literally it's one section of a plane engine essentially
@russcole5685
Жыл бұрын
@@borttorbbq2556 What!
@borttorbbq2556
Жыл бұрын
@@russcole5685 yeah I don't know if it would actually work today but Harley-Davidson's the 45° twin-style motor is based on plane engines a single I'll just call it a Cell of a plane engine is essentially the twin motor and it's like 8 to 16 of them or something like that that are all put into series that get the specifically for prop planes so this is going to be like your Cessnas and such I don't know what plane engine it was actually derived from but basically
@borttorbbq2556
Жыл бұрын
@@russcole5685 I think you could use something like a Galaxy gear oh my Galaxy Gear and then just have it so that the motors are spinning the outer ring just so you can have your prop shaft running down the center of it basically think how monster truck wheels are in Reverse basically. And yeah if you take and you put enough of those into a single layer I think you can fit something like six or eight per layer and you just start stacking those layers after three or four maybe even five layers you will end up with one just absurdly powerful plane engine
@theyeetus1428
Жыл бұрын
@@borttorbbq2556 I don't think any functional plane has a V32.
Time spent on projects like this engine is time well spent 👌
That’s dope man
This knuckle head engine would be awesome in a three wheeler. That was a very healthy spark it shock like a real one also had the same sound also. Thanks for sharing this with us. Love your channel and content. ❤🇨🇦
SO MUCH POTENTIAL!!! 👍👍👍
Finally a motor with spark plugs! Great vid, keep up the good work
@ferrumignis
Жыл бұрын
He's built loads of engines with spark plugs?
@Jc-kx5gk
Жыл бұрын
He uses mostly glow plugs
@VitoFur
Жыл бұрын
@@ferrumignis He has a few, but most of the engines are nitro, so they have glow plugs
@Rcguy2591
Жыл бұрын
@@ferrumignis he didn’t build this…
Maybe some RC motorcycle like some old harley WLA with sidecart👀
@jedpetersen3806
Жыл бұрын
Definitely 😁
Thank you ☺️
Wicked machine 🙌
I'd love to see a mini V6. Maybe a VQ style. See how trumpety a mini one of those would be 🤣
@smashface3080
Жыл бұрын
Even in a miniature vq it'll sound like trash and farts
@offtap6
Жыл бұрын
3.8 Buick 3800 would be killa
@genefogarty5395
Жыл бұрын
Stirling makes a bunch of miniature engines.
Impressive definitely do an rc motorcycle! Sounds like a beautiful challenge good luck!
very cool, JQ90…as usual
Words can’t describe how cool this is. Bad to the bone 🦴
I am amazed at how much this little thing sound exactly like a Harley
That sounds awesome. You should make a trike or quad with one of those. That would be awesome
@aytugbaykara2690
Жыл бұрын
harley davidson v2 sound
even sounds like a Harley v-twin.
Beautiful 🤘
This is too cool!
Superb 👌🏻
Not a lot of oil on those cam drive gears, grease might be a good idea but be careful not to upset the timing by turning the engine over without the cover on. How do you add oil to the crank case ? ?
@leviwilder1205
Жыл бұрын
to my ears, owning a knucklehead myself. It sounded like it was already out of timing by a pretty large margin, almost as if it was fighting itself
@mhz-yn9gh
Жыл бұрын
Ian, I have this engine & did the same as you mentioned; removed the cam chest cover & lubed the lobes & gears. No oil in bottom end. I run Coleman fuel / 3% Marvel Mystery Oil. After a little time is on the engine, i layed my engine flywheel side down, to check if blow by lube was getting to the crank. Yep, oil residue comes out the timing “peep hole” Glad to know crank gets enough lube 🤙
@alanhardy3374
Жыл бұрын
Dab of Vaseline maybe ?
@johnnyq90 seems like it's throttle response kinda slow to me. Does it have a better build quality than the other v-twin you have?
I find it interesting that they made this engine spin backwards to a usual Harley engine.
@MrBuellMike
Жыл бұрын
…exactly what I thought too…!?
Excellent!
They got it right on this one even the annoying sound..
That is so cool!!
Very cool!
Wow that is awesome how you built the carburetor ignition timing and made it sound so but on perfect it's phenomenal and then you turn it into one kicker absolutely awesome I'd love to see the video of your building the whole thing including especially the carburetor
@genefogarty5395
Жыл бұрын
It's bought from Stirling engine kits, 900 bucks.
@JohnnyQ90 you could make a programable / adjustable load to simulate upshifting and downshifting sounds with these tiny motors on stand so we can hear what they would sound like mini ripping!
Fnatastic! Just too sweet! Some questions if that okay. How are the pistons lubricated? What kind of carburetor does it have. The drive train?
looks like a collectors item XD
Jeezus!! Real spark plugs? LMAO !! Out fkn standing !!!
idk if this guy made this himself but ive seen thigns on youtube that peopel do craft engines this small and they work its pretty neat..
Johnny you gotta do a motorcycle or trike RC build with this knucklehead engine!!! 🙏🙏
Beautiful
Good stuff
I think JohnnyQ90 is just a giant working on normal sized engines
Pretty nice little engine, though the pressed steel valve gear covers look a bit cheap and nasty. Sounds like the fuelling needs to be fixed as well. BTW it's really not a good idea to pull HT leads off with the engine running, this puts a lot of stress on the coil insulation and the primary side drivers.
Damn, I could use that idle sound to sleep every day 😎
Yes a trike gotta make it would be insane
it even shakes well
It would make a great addition for "The Mouse and the Motorcycle."
Awesome!!
It sounds good, I am imagining it in some RC Harley, or something like that xD it would have a realistic sound too.
This is beyond belief ! What does he do for a living $ ? Genius !
Holy sh!t, sounds better than a full sized Honda.
That's awesome. Now you need to build a small Harley Davidson to put it in. 😉
Awesome 👍
is there oil in the crankcase? is there a Magneto to charge the batteries?
Even starts slowly, like a knucklehead!
it sounds like a mini Harley Davidson which is pretty cool!!
For some reason. Seeing this motor reminded me of the 1976 Harley Davidson Electra Glide that Elvis used to ride.
Why did you run it backwards flywheel rotation? Does it run better backwards
I can't imagine the time it took to build this engine. WOW
@hoverbotfpv1425
Жыл бұрын
Made in china microcosm been on eBay a long time.
Awesome
A rat rod trike would be so awesome
Awwww, its adorable!
Hi does it got that much power to put on rc car?will it work or doesn’t have that much power please tell your opinion thanks
my biggest gripe with tiny engines is how annoying and whiney they sound, So honestly something like this is so cool just because it sounds so close to the real thing!
What's the name of the small electric screw driver used in the video? Been looking for a small one to work on smaller electronics that use the small precision bits.
@mhz-yn9gh
Жыл бұрын
It’s a “Sequre ES126” I’ve had mine for a year and love it.
what a lovely day