1st start up and test drive with the 0.30 over 400 sbc comp cam aluminum trick flow heads th350 trans 3500 stall and 3:73s
Жүктеу.....
Пікірлер: 43
@jeffloewen15603 жыл бұрын
The 400 is a torque monster love this engine
@greggarner44773 жыл бұрын
God I miss my 80 Malibu!!! Beautiful car
@decondiclifton9937 Жыл бұрын
Classic, Clean & MEAN ASF 🥶💪🏾👑
@antj211 Жыл бұрын
Nice build what engine idle speed did you go with
@44ozcup4 жыл бұрын
Nice Malibu! I have an 84 Monte Carlo I'm building a 383 for. What did you get your serpentine belt setup off of?
@SSPENGINES383
4 жыл бұрын
Off a 90s model c1500 pick up
@rush66174 жыл бұрын
That mothaphuka runnin 👌💪
@steelcitycaprice.8993 жыл бұрын
U THE TRUTH BRUH...👍😎🔥🔥🔥🔥🔥🔥
@DA-cg3du3 жыл бұрын
I have the same engine in a 1964 impala SS, it has a th400 2500 torque converter, but i feel it’s not performing at it’s best, could you tell me what timing is good for it, the person who’s looked at it says you can’t set the timing with a flash gun, so he was kinda guessing it, any advice on what I can have it set at? Thanks
@Superchevy88 Жыл бұрын
Nice
@Mr.Frost181 Жыл бұрын
Is that serpentine setup from my OBS truck
@vicsspeedperformance9503 жыл бұрын
Mf sounds awesome bro , sound like it pinged a little when you got on it , take a little timing out but she is laying it down 💯🔥🔥👍🏼
@brandonwillingham30654 жыл бұрын
Is it possible anyone knows the guy selling the Malibu?
@scummbagracing42414 жыл бұрын
Cam spec's
@HighPowerOptionsTrades Жыл бұрын
How do you stop it from fishtailing ?
@justinhamilton45573 жыл бұрын
What size roller cam
@domib38734 жыл бұрын
Do you remember what heads those are ??
@SSPENGINES383
4 жыл бұрын
Trick flow heads
@GazaStrip90210
3 жыл бұрын
@@SSPENGINES383 Do those heads have the steam ports that the 400 blocks require? My Malibu and I are in the caribbean, options are limited, but i do want to upgrade the heads on my SBC 400. any help/info is greatly appreciated.
@SSPENGINES383
3 жыл бұрын
@@GazaStrip90210 no they dont have the steam holes drilled and run perfectly fine
@mattv8919
2 жыл бұрын
@@SSPENGINES383 watsup man, just picked up a mostly stock 400 last friday. rpm performer , 600 holley, long tube going in a mostly street driven el camino. what would you reccomend for heads and cam and stall ? wish i could build a 400 like yours but budget dont allow it. always watch your videos. from california
@SSPENGINES383
2 жыл бұрын
@@mattv8919 there are many good affordable options but until u know what heads u going with it's hard to determine cam and stall
@jackclayton83603 жыл бұрын
where your shop is?
@jeffnunley1861 Жыл бұрын
What cam u running
@wisheye14 жыл бұрын
hydraulic roller cam?
@SSPENGINES383
4 жыл бұрын
Yes it is
@58chiefton3 жыл бұрын
First you got skills and that 400 runs and sounds wicked...just one question what kind of serp belt bracket set up is that? And what modifications to make it fit?
@justinhamilton4557
2 жыл бұрын
Just take the same setup off of any 350 tbi
@58chiefton
2 жыл бұрын
@@justinhamilton4557 Thanks for the info👍
@coreygilstrap7809 Жыл бұрын
Fast idle screw 😅
@71donkrider3 жыл бұрын
I heard 650 is two small.. and 750 cfm better
@joejackson9172
3 жыл бұрын
650 is def too small for that motor
@KingJT80
3 жыл бұрын
Depends on what rpm range and use for it is. Bust most times yes a 750 is needed but customer have what they have im guessing
@joejackson9172
3 жыл бұрын
I agree. The 650 might feel ok around town. But since he is trying to get the quickest et, it's killing that 440 for sure.
Пікірлер: 43
The 400 is a torque monster love this engine
God I miss my 80 Malibu!!! Beautiful car
Classic, Clean & MEAN ASF 🥶💪🏾👑
Nice build what engine idle speed did you go with
Nice Malibu! I have an 84 Monte Carlo I'm building a 383 for. What did you get your serpentine belt setup off of?
@SSPENGINES383
4 жыл бұрын
Off a 90s model c1500 pick up
That mothaphuka runnin 👌💪
U THE TRUTH BRUH...👍😎🔥🔥🔥🔥🔥🔥
I have the same engine in a 1964 impala SS, it has a th400 2500 torque converter, but i feel it’s not performing at it’s best, could you tell me what timing is good for it, the person who’s looked at it says you can’t set the timing with a flash gun, so he was kinda guessing it, any advice on what I can have it set at? Thanks
Nice
Is that serpentine setup from my OBS truck
Mf sounds awesome bro , sound like it pinged a little when you got on it , take a little timing out but she is laying it down 💯🔥🔥👍🏼
Is it possible anyone knows the guy selling the Malibu?
Cam spec's
How do you stop it from fishtailing ?
What size roller cam
Do you remember what heads those are ??
@SSPENGINES383
4 жыл бұрын
Trick flow heads
@GazaStrip90210
3 жыл бұрын
@@SSPENGINES383 Do those heads have the steam ports that the 400 blocks require? My Malibu and I are in the caribbean, options are limited, but i do want to upgrade the heads on my SBC 400. any help/info is greatly appreciated.
@SSPENGINES383
3 жыл бұрын
@@GazaStrip90210 no they dont have the steam holes drilled and run perfectly fine
@mattv8919
2 жыл бұрын
@@SSPENGINES383 watsup man, just picked up a mostly stock 400 last friday. rpm performer , 600 holley, long tube going in a mostly street driven el camino. what would you reccomend for heads and cam and stall ? wish i could build a 400 like yours but budget dont allow it. always watch your videos. from california
@SSPENGINES383
2 жыл бұрын
@@mattv8919 there are many good affordable options but until u know what heads u going with it's hard to determine cam and stall
where your shop is?
What cam u running
hydraulic roller cam?
@SSPENGINES383
4 жыл бұрын
Yes it is
First you got skills and that 400 runs and sounds wicked...just one question what kind of serp belt bracket set up is that? And what modifications to make it fit?
@justinhamilton4557
2 жыл бұрын
Just take the same setup off of any 350 tbi
@58chiefton
2 жыл бұрын
@@justinhamilton4557 Thanks for the info👍
Fast idle screw 😅
I heard 650 is two small.. and 750 cfm better
@joejackson9172
3 жыл бұрын
650 is def too small for that motor
@KingJT80
3 жыл бұрын
Depends on what rpm range and use for it is. Bust most times yes a 750 is needed but customer have what they have im guessing
@joejackson9172
3 жыл бұрын
I agree. The 650 might feel ok around town. But since he is trying to get the quickest et, it's killing that 440 for sure.
Running 🏃 !!!!!
wat yr 400 n casting#?
💪🏾👍🏽🏁
🐗💯
damm cuhh
Sideeewayysssss🤘🏾
Classic, Clean & MEAN ASF 🥶💪🏾👑
What cam u running