Just finishing up rebuilding the cylinder was just like a normal cylinder with double the seals. To get the cylinder apart on the c clip side tap it in to reveal another retainer clip remove that and slide it out from that side. Then replace the seals and your good to go
@danbergie8
10 ай бұрын
Seal kit 85966
@denhawken6 ай бұрын
Oof i gotta do this for the big one we got... thanks for info
@jaked74912 жыл бұрын
I found this video helpful,, but need to know how to take the cylinder apart....
@samgreen6144
2 жыл бұрын
I'm sorry I don't know how to take it apart, I just took it to a hydraulic shop to get rebuilt.
@jaked7491
2 жыл бұрын
@@samgreen6144 ok sounds good that's probably what I will have to do too,, but if I figured it out I'll let you know details.
@seaquest5412 Жыл бұрын
Hey, is there anyway I can speak to you about what you did here, because I am doing essentially the same thing but on the rear axle and on a gehl. I cannot remove the whole thing (trust me), but for the life of me, I cannot get the inner tie rod end to unscrew from the ram. I've got like 5mm clearance at the end of the ram to grip and it is NOT working no matter what I try.
@jaked74912 жыл бұрын
What's the rest of process to rebuild that cylinder?
@samgreen6144
2 жыл бұрын
I'm sure the cylinder gets rebuilt like any other cylinder, I don't know how to do that though I've never rebuilt one I always just take them to a hydraulic shop, especially when they're very large cylinders like this one.
@tolomartinez66722 жыл бұрын
How much would a job like that go for?
@samgreen6144
2 жыл бұрын
$400-ish. Plus the cost of the Piston rebuild, a hydraulic shop charge me about $700 to rebuild the piston
@tolomartinez6672
2 жыл бұрын
@@samgreen6144 aw ok i thought I had f.. My self i charge 350 plus parts
Пікірлер: 15
Just finishing up rebuilding the cylinder was just like a normal cylinder with double the seals. To get the cylinder apart on the c clip side tap it in to reveal another retainer clip remove that and slide it out from that side. Then replace the seals and your good to go
@danbergie8
10 ай бұрын
Seal kit 85966
Oof i gotta do this for the big one we got... thanks for info
I found this video helpful,, but need to know how to take the cylinder apart....
@samgreen6144
2 жыл бұрын
I'm sorry I don't know how to take it apart, I just took it to a hydraulic shop to get rebuilt.
@jaked7491
2 жыл бұрын
@@samgreen6144 ok sounds good that's probably what I will have to do too,, but if I figured it out I'll let you know details.
Hey, is there anyway I can speak to you about what you did here, because I am doing essentially the same thing but on the rear axle and on a gehl. I cannot remove the whole thing (trust me), but for the life of me, I cannot get the inner tie rod end to unscrew from the ram. I've got like 5mm clearance at the end of the ram to grip and it is NOT working no matter what I try.
What's the rest of process to rebuild that cylinder?
@samgreen6144
2 жыл бұрын
I'm sure the cylinder gets rebuilt like any other cylinder, I don't know how to do that though I've never rebuilt one I always just take them to a hydraulic shop, especially when they're very large cylinders like this one.
How much would a job like that go for?
@samgreen6144
2 жыл бұрын
$400-ish. Plus the cost of the Piston rebuild, a hydraulic shop charge me about $700 to rebuild the piston
@tolomartinez6672
2 жыл бұрын
@@samgreen6144 aw ok i thought I had f.. My self i charge 350 plus parts
How long did this job take?
@samgreen6144
2 жыл бұрын
About 6 hours if I remember correctly
@r6erbuyafool
2 жыл бұрын
@@samgreen6144 thanks bud. I’m about to do one