Thank you for the help bud worked great 👍

Best video for rebuilding my John Deere loader tilt cylinder. Lots of tricks learned, great delivery, instills confidence....thank you very much!

I’ve watched all the videos and yours was a good one all the content needed and not long winded.

Great video! Just rebuilt all of my front loaders cylinders with no errors thanks to this video

I'm well into my repair job on my 200CX FEL. Your video is my bible, sir! Thanks a million.

thanks for sharing, that is something else the way they designed that cylinder and needing a special tool for the snapring!

Very good explanation of how to do this replacement of seals.

Thanks for putting this video up. It was very helpful. My local dealer in Van Alstyne, Texas had the kit in stock. This is for Bucket Cylinder 420 Loader 013054 - ST406437 with rebuilt kit part# AH176344. Be warned, the kit doesn't come with a gland removal tool. You have to buy it separately. Maybe another kit has it included but the one I got didn't have it.

This was an incredibly valuable video! Thank you!

Great job on explaining the process. Very helpful.

Awesome video watched as I just rebuilt the cylinder on my skidsteer no leaks now

Thanks for the great video!! I have a JD400 tractor with a Brantly 420 loader and I’m sure the lift cylinders need rebuilding. I’ve been looking for a video that deals with this size and style of cylinders. Much appreciated. Great description and presentation. Thanks again. 🙂👍🏻👍🏻

Very good I picked up a couple of cool tricks! I enjoyed the video!

I appreciate your video my friend,you are the best!!!

You were very helpfull, Thank you.

Thanks for the video helpful!

Great video, man!

The torque spec on this is... 'all of it'. LMBO!!

PS, the hack using the leather and a hose clamp is priceless!

Thanks for explaining the orange ring. What a bogus design. Rebuilding a JD770 steering cylinder. Thank you!

Ty brother for insight God bless you gotta do this on jd 850 tractor ty

Like a piston ring compressor but home made type

thanks for posting video!!! where do you obtain the seal kits?

@jimjordan5630

7 күн бұрын

That was going to be my question. Hopefully a good quality reliable seal kit not from JD, Amazing or eBay and hopefully definitely not since made in Chy-Na! 😂 Being your question was a month ago with by response I guess we might be out there with Bob Dylan and left blowing in the wind! 😂

What about the o ringe on the rod behind the nut ?

My bucket cylinders on my 430 loader do not move at the same speed, is this an indication a rebuild is needed?

Watch Wes Work demonstrated a neat tool for installing the inner seal recently when he was rebuilding a cylinder for his skid steer.

@ffrepeat

9 ай бұрын

I have the tool, but I have been doing by hand for so long I forget I have it. 🤦‍♂️

@stacymarbach988

9 ай бұрын

Wow! Such an informative video!! Looking forward to the next episode!

Is there fluid needed in the cylinder?

Takes strong fingers and hands to force them in or buy the high dallor tools and there worth it once you start lolol

I hate the jd cly type but I’ve done plenty of them over the years Thanks

no its not easy !

We are repairing cylinders from a 158 JD loader - the outer snap ring on ours does not have the holes in it to grab with the snap ring tool to spread it- do you have any suggestions as to how to get that back on? We’re having a dilly of a time trying to get it back in place.

@user-ms7lg1bd5b

5 ай бұрын

Those retaining rings are the worst, my advice is to be creative… I have made at least 3 different tools just for those stupid retaining rings

@ffrepeat

5 ай бұрын

Try these LEONTOOL 11-Inch Lock Ring Pliers Flat Snap Ring Pliers Special Circlip Pliers Reverse Pliers Angle Tip Retaining Ring Pliers Ring Opening Pliers Spreader Pliers for Transmission Transfer Cases a.co/d/5re7T8i

@LivingRural1983

4 ай бұрын

I used regular snap ring pliers that have the pins. Just below the pins, they have a flat area that worked great for those round snap rings. To compress the internal snap ring, I found that a CV joint clamp worked the best for me. It is thin enough to slide partway into the end of the cylinder.

At 18:40 - "There is a tool for this, but I never use it." I may need to order it. I've spent about 45 minutes trying to get this seal to behave. I am working on a smaller diameter cylinder so maybe it is especially hateful. What is this tool called?

@ffrepeat

Ай бұрын

a.co/d/bGAQ2qA This is the tool on Amazon

hurts my heart. i tried and tried but mine would not go in any further. was like a suction that was fighting me in or out. ended up just dropping it off. $270 was the damage. and now i know i have another problem as the piston won’t extend up (out). only down (in). unless i reverse the lines. 😭

@user-iu8wt2jz9j

Ай бұрын

do you know how they fixed it? I'm currently stuck with the suction pulling the rod back in as well. It's like playing tug-of-war with an elephant

Appears you skipped the removal of the inner snap ring that needs to come out before putting in the "tool" in its place.

@ffrepeat

5 ай бұрын

Nope….the tool is there to allow the snap ring to compress so you can remove the gland.

Show from the beginning, like taking off the spanner nut, need to redo 1978 70 series john Deere lift arm cylinders, can't see any spanner rings on this model. Spanner nut turns and turns but won't come off any ideas thanks jim

I have a 1978 70 series john Deere skid steer. Trying to put new seals in lift arm cylinders It has the spanner nut at the end . It turns and turns and will not come off. I can't see a lock ring any where. What am I missing

@ffrepeat

6 ай бұрын

What model is the loader?