Skogenracing: Ford Pinto iS turbo - 304whp with stock engine
Автокөліктер мен көлік құралдары
Our little projekt we built for scrap Money (under 2000usd)
Two goals, first to drive a eleven second time on the quartermile and the second was to take it to 300whp without open up the Engine and change parts. we manage both things and it still works fine!
Пікірлер: 85
I come back to watch this at least once a year. Love it
Just as sierras should be built, on budget, only turbo related stuff! I literally dream of being able to build sierra like that for scrap money... Awesome! Badass turbo badassery! Thanks for the vid!
@Skogenracing
8 жыл бұрын
+NGC1433 Thanks!!
@olsenautofix
3 жыл бұрын
i got a 2.0i s mk2 for 100$ running and good condition. the same as on the vid only i have mk2 front with morette lights
you guys are kings!!
That Rocks!
Kul bygge!
Which ECU used in this project?
this video just wanted me to buy a sierra again, just sad the most of them are gone from rust now :/
hello can give some specifications of assembled material thanks
I know i probably wont Get answer but what did you guys use for fuel controlling and did you guys adjust the timing and can i build and run on 98 octane
This is some quality entertainment. Kinda reminds me of the times when I just started following your videos when you were doing these budget builds, even before the videos were uploaded to youtube! Oh and I gotta say, under 12 seconds in a Sierra with "only" 300+ whp is quite impressive. Any other modifications to the rear than the obvious locking diff and good slicks?
@Skogenracing
8 жыл бұрын
+PePe Thanks, we have lost i a little bit, growing older and more boring :) We welded the diff and made a new bracket for the differential thats all
@PePe_FIN
8 жыл бұрын
+Skogencrew Skogencrew Sounds good :)
@PePe_FIN
7 жыл бұрын
Oh BTW what clutch did you use on this one? I'm currently looking for the different options I have. I will need a clutch that can hold the torque of a 300 to 400 bhp (eventually) turbo Pinto and am wondering if there are any options that will be a "straight fit". Currently the the only options that I have found will require changing to a different flywheel for either a bigger clutch or to 184 mm racing clutch.
1:42 добрый дядюшка - тюнер !)
@FANTOMCHANEL01
4 жыл бұрын
дада
Hei, er der orginalt drivverk på sierraen? T9 kasse og org bakaxel?
Thats where all the 3dr are 😂
How would that little car do with some sticky drag tires like a set of wrinkle walls
Hi ... Nice project.. what type of intake and Turbo manifold did you use ? Keep it up ! :)
Vad körde ni för tid och hastighet på 201m? Kör själv Sierra turbo så vill ha något att jämföra med:)
What clutch and are u running it on stock type9 transmission?
Hello .. I have a sierra pinto I want some power. what can you recommend to be something like this. and can you send everything I need in Croatia or Bosnia. to make arrangements for everything else because it is difficult to find parts here. Thanks .
How long this motor lasted? What was the boost amount?
+ Skogencrew Skogencrew after read the comments .... I Can not Have the same reaction in a 2.3i lts? What Makes the diference Between 2.0 to 2.3i ?? and what's necessary to have it? thanks
Yes!!!
Nice project. what parts were used ? greetings
Hello colleagues can tell me that turbo and collectors placed I am interested in doing this project I have a saw 2.0i ohc pinto thank you and greetings
What is the turbo off? Or can you purchase 1 to suit
@skogenracing - Can you send me full spec of this car :D?
Stock type9 gearbox?
What is the fuel ?
Hi, I have few questions. Were you running stock headbolts ant gasket? :)
@Skogenracing
4 жыл бұрын
yes
What ECU are you guys running with this? And was it plug and play?
@Sierraman59
Жыл бұрын
Megasquirt
Engine parts?
Is it stock gearbox and stock clutch or reinforced ? Could you send here or on your page the full list of setup and parts please ? thx, badass project
@theeverythingguy8532
5 жыл бұрын
actually the gearboxes in all generetions and motor types of sierra are pretty strong, they were placed in mustangs too. legends say that they can handle up to 400 horses
@KevinFromHPCustomerSupport
4 жыл бұрын
@@theeverythingguy8532 A bit wrong there. You're talking about the T5 gearbox, which only comes in the higher-ish spec Sierras, the lower specs get Type 9's (like mine )which unfortunatly, from what I hear, WILL shit the bed with abuse :( I'm onna turbo mine but I will need a gearbox solution
@theeverythingguy8532
4 жыл бұрын
@@KevinFromHPCustomerSupport oh yeah, sorry. so it looks like I have T5 gearbox swapped in my pinto sierra from previous owner, i dindt know that i have such a good thing in shitty 2 liter ohc :D
@Flewkey1337
4 жыл бұрын
@@theeverythingguy8532 How much power you running? Because I highly doubt you'd have a T5 gearbox they're quite expensive, you probably have the MT75 gearbox.
@theeverythingguy8532
4 жыл бұрын
@@Flewkey1337 about 250 hp now, dont know the torque. Cam, higher compression, exhaust, diesel fiesta rods conversion (so its 2.1l), 0.6 bar of boost, draw thru carbureted setup. Whatewer gearbox, it holds strong
That wasn't a stock intake manifold. 304 RWHP on 26.1 PSI/1.8 BAR from a stock block sounds about right. A bunch of 2.3l Mustangs here in the US will push 400hp plus on pump gas with camshaft and cylinder head improvements
@Skogenracing
8 жыл бұрын
now but stock works fine for around 400bhp but we manufacture our own for a better looking engine bay. this is the 2.0 engine, the 2.3 i a different engine
@tap12892
8 жыл бұрын
+Skogencrew Skogencrew 2.3 is different than a 2.0 but there both pinto based. And always heard 2.3 makes more power/tq than 2.0. Am I wrong? What's the advantage of having a 2.0 vs 2.3.
@megt8564
7 жыл бұрын
Skogenracing - did you install forged engine internals
@megt8564
7 жыл бұрын
Skogenracing - how much boost?
@espenschjelderup426
5 жыл бұрын
@@tap12892 I know, old post. Maybe you know by now. The 2.3 is from a different engine family, the ohc Lima(US) family, that also have a 2.0. The engine in this video is from the ohc Pinto(Europe) family, and the 2.0 is the biggest from factory.
1.8 bar without using forged connecting rods or pistons? didn't they really open it?
@Skogenracing
4 жыл бұрын
Yes all stock. we did not even open it
@federicoelias1676
4 жыл бұрын
@@Skogenracing Very good project !!!! Greetings from Argentina
How much did you spend on total? Awesome build, I wish I had the skills to build myself a budget RWD turbo sleeper :D
@Skogenracing
9 жыл бұрын
Gladki007 We had some parts laying around and with that we spent 15000kr or 1700usd to a complete build
@ASHLambretta
8 жыл бұрын
Under $2000 usd in the description so im guessing turbo intercooler intake and megasquirt
@ritter_cracker
8 жыл бұрын
+ASHLambretta ECU Master EMU actually.
I want to build my lx foxbody like this I want to do the exact same
@capi6204
Ай бұрын
did you do it?
Hi! What fuel injectors do you used on this engine?
@Skogenracing
6 жыл бұрын
MSD 1000cc injectors
@Leciffre
6 жыл бұрын
@@Skogenracing thank you! :)
is it difficult for a novice to program megasquirt ?
@capi6204
Ай бұрын
yes
depends on how much is scrap money for you... because i dont think that forged internals are cheap...
@Skogenracing
9 жыл бұрын
There is no forged interiors in this engine! Its completelly stock on the inside
@Malfik
9 жыл бұрын
Skogencrew Skogencrew and stock sierra engine will hold 1.8 bar and 300 hp???
@doctorstruts
9 жыл бұрын
Tomáš Staněček I know people who runs a bit over 2 bar with stock internals, but there is more things than boost preassure to keep in mind ;p
@Skogenracing
9 жыл бұрын
Tomáš Staněček Yes this was one of our Project goals. To build a pintoturbo, get 300whp without open it and driva an elevensecond time on the dragstrip. We wanted to now if it was possible and it was!
@PePe_FIN
9 жыл бұрын
Tomáš Staněček Oh and may I also add, if you want better internals for the piece of mind, you could use std Cossie ones. If you are willing to spend some time hunting for parts you can find used pistons and rods for only few hundred quids (around here at least). IIRC I paid 300 euros for my pistons and rods and I have been running 1.5 to 1.8 bar of boost with them in the street for few summers already :) So yeah building these engines can really be done with a relatively low budget.
What wastegate did you use?
@Skogenracing
8 жыл бұрын
+TheMR2V6 it´s a copy of a HKS
What song in the last part =)
@skogsberger
9 жыл бұрын
MrBasserk Its Dethklok - Face Fisted
what ecu did you use ?
@Skogenracing
9 жыл бұрын
drunkbob31 Ecumaster EMU
Is that engine still alive?
@mysticpvpgaming9069
5 жыл бұрын
wondering the same thing, i got a 2.0 pinto too with a TD06 turbo kit im dying to install
@mikrafonaslopas
5 жыл бұрын
@@mysticpvpgaming9069 you made a manifold by your self or found somewhere to buy? tell more about the kit
@andriesgeddes4692
5 жыл бұрын
@@mikrafonaslopas the car came with a turbo exhaust manifold when I bought it.