Thank you for this, it was most helpful when I did my own service on my TRA. You should do a vid on the secondary.

Great Video! Definitely helps take away the scariness of tearing apart your primary.

Very well illustrated and explained. And fast forwarded through all the loosening and tightening sequences. thanks

Excellent video plenty of lighting. Not all of the other non-valued added crap. Very well explained. Thank you!! 🏆🏆🏆

Love the video and the fact that the starter gear said made in the USA .

This is a GREAT video! Excellent quality and easy to understand! THANK YOU!

Excellent tutorial!

Excellent tutorial! Many thanks

That is just the information I needed

Great video. Helps a lot with what I have to do! Thanks for the info.

Thank you! Great help for working on my clutch.

Awesome video, helped a lot with my 1997 mxz.

Excellent vid..

I had a bad rattle while idling on my 04 rev 800. Replaced the o-rings between the buttons with some oversized ones I had from a harbor freight kit. Problem solved, runs like new. This video helped tons with the removal and install. Thanks

@danieledelman8178

Жыл бұрын

this also helped out others. thanks very much

Thanks man you saved me 1000$!

Real good

Great info and video quality. One of the best I've seen. Maybe just lose the music during the r&r process

Great vid. Thanks for the upload. Da wife's 2014 600 Adrenaline clutch is rattling something wicked. I figure it's very similar to the one in this vid?

Great video!! I have a 1996 ski doo summit 670, and want to try to pull the clutch. Is there a lot of differences? The outside appears similar.

Thanks! Can you make a video for secondary clutch removal off sled , inspection disassembly and assembly!

Excellent video, so those roller arms… would you have to replace the entire arm or is there a bushing that can be replaced?

On the 08 I put the two halves of the clutch together how do I know if it is on all the way mine has some play

Is the spring retainer on all TRA clutches? If that is the case mine is missing

Where can I find just the spring retainer part that is mentioned at 12:43? I can’t find anything online. Does it possibly go by a different name?

I just diasssembled my Freeride clutch for cleaning and inspection. The spring retainer cup alignment mark was one bolt hole off at the 8:00 position. This is the first disassembly of the clutch so it came that way from the factory. Should I reposition it with to align with the other marks or leave it the way I found it when I go back together?

I just picked up a 2008 ski-doo rev xp 800 snowmobile and it was missing one of the calibration screws. I picked up a replacement screw, washer, and nut. I put it in and set it to a three like the other ones were. There is no need for me to pull the clutch all apart, correct? It looks like the ramps just push back and forth. Or am I missing something? I think there was maybe supposed to be a washer that goes on the inside?

My clutch has a spring that goes in before each button

Very good video! How much play is acceptable between the lower clutch arm bushing and the pin? I assume just side-to-side play without any rocking motion?

@rawfueltv3874

5 жыл бұрын

Yup. You're correct. Slight side to side is acceptable but rocking can often lead to sticking which wears parts and reduces efficiency.

Where are the springs behind the button slides?

can someone explain to me how the belt turns and how it grips on the primary clutch and secondary clutch if theres is no grab for the inside belt.

What is wrong if I cant split the primary like you show on a 2016 Lynx Boondocker 800 ETEC...?!? I thread in the tool 15mm and use a small sledgehammer.... and nothing... Even with harder smashes nothing happens, what is wrong, is 2016 Tra different?

What if my movable sheath is refusing to separate?...

great video , I have 2014 800 etc , I dont have a clutch puller tool , what size bolt can I use to make this ? or you recommend the place to buy one ? I have 4000 km on the sled and never service the clutch yet .

@rawfueltv3874

6 жыл бұрын

Mike Krukowski, we use the primary clutch removal tool from brp so if you care to do it that way go to your local brp dealer and pick it up. If you don't have that available KZread search clutch removal water trick it will get the job done!

What if it doesn't come apart when you hit it with a hammer? Then what? Thanks

Wondering what is acceptable on the ramps. I definitely see wear lines, but not sure what is acceptable

@rawfueltv3874

5 жыл бұрын

Generally when we see moderate to significant wear we change out the ramps. They will still function however their efficiency and tendency to wear other parts is compromised. Preventative maintenance like this is a good way to get you to to the end of the lake quicker than your buddy.

Is this the Primary or Secondary clutch? I'm assuming the former.

@rawfueltv3874

7 жыл бұрын

Shaine MacDonald in this particular video we're working on the primary. It's not terribly difficult. Just ensure you take your time and maybe a photo or 2 prior to disassembly so you have a reference point.

Whats the good place to get your replacement parts? I m working on 2014 Summit 800 , thanks

@dallaswiller

3 жыл бұрын

Dennis kirk

Is it necessary to have my primary clutch balanced after a rebuild? Thank you.

@phantomfarmer8041

2 жыл бұрын

No

Hi I just removed the clutch but forgot to make marks.. how to do a balance ? thanks

@rawfueltv3874

6 жыл бұрын

mikeracer27 you'll need to look for the factory punch marks, arrows, or small half moon cut outs for alignmemt. And they won't line up 100% but they'll be extremely close depending on you application of course.

How bad is it if I forgot to mark my clutch and might not have put it back together right? And this is not the clutch I have mine is off of a Polaris indy 1993 500

@ilikewaffles9744

3 жыл бұрын

I didint take the whole thing apart just the main cover got stopped by the spider nut that I did8nt know was there

Hello! I have a problem! snowmobile installed clutch like 2009 Etec at idle a knock is heard in the clutch, sometimes disappears. after removal and inspection, wear of parts was minimal. Please tell me why a knock may appear.

@davidakoak1974

5 жыл бұрын

Have you checked your bearing behind the primary clutch?

@davidakoak1974

5 жыл бұрын

But the downside is if you check it, you would have to buy the special grease they use for that bearing. Also the seal on the otherside of the bearing could break if you apply to much grease.

for the weights, what weight should I use for explosive acceleration

@rawfueltv3874

7 жыл бұрын

Brock Kleiman unfortunately as you can imagine clutch tuning isn't as easy as switching out one component. Every change you make will have an effect on the rest of your shift or engagement action. If you really want to do some clutch tuning I recommend purchasing and reading the Olav Aaen Clutch Tuning handbook. It's the bible of the cluth world. If that's not your thing then look at purchasing a clutch kit from a reputable manufacturer like Cudney Racing. He's already done the calculations and will get you pointed in the right path. Check him out at www.cudneyracing.com or 519-682-0626

@brockkleiman9275

7 жыл бұрын

Raw Fuel TV I have already ordered a Dynamo Joe clutch kit and installed the adjustable weight pins, but I don't know what will happen when I use heavier or lighter weights

@rawfueltv3874

7 жыл бұрын

Brock Kleiman because the answer to this question is quite lengthy. I found an article on what the weights do. As well as the effects they have on the clutch itself and how the primary and secondary interact with each other. Check it out here. It's not specifically written for a modern day Ski DOO clutch. But the principals remain the same for snowmobile clutches in general. www.totallyamaha.com/snowmobiles/aaTECH/tuning/tuning.htm Steve

@ashiqakashiqak4356

6 жыл бұрын

ashiq

@jaridwilliams8459

6 жыл бұрын

Brock Kleiman

I have two lever arms that are really tight and do not move freely at all on my 800 etec clutch. Any suggestions on what might need to be done to remove them? Seems like they are pressed into the slot somehow once I took out the set bolts. I hear on your video the levers clinking easily as you rotate the cluth... only one of mine is doing this at the moment. Thanks.

Good video but the music is stressing me out

How much HP can this clutch handle

@erik041982

3 жыл бұрын

Can handle as much hp as the belt and chaincase will take

@phantomfarmer8041

2 жыл бұрын

I've seen em take 350+hp

wheres the bushing , your clutch seems to be missing the internal bushing.

hi i have a problem where are all bussings tra 3?

@rawfueltv3874

7 жыл бұрын

During the disassembly process you'll see all the bushings/orings/spacers. There are 6 o-rings on your buttons (shoes, sliders) the buttons themselves, 6 spacers, the pins etc... the video looks at all of those components. If you still have problems locating them, check out the"owners" section of the Ski-Doo web site. Look in the parts section, find your model and you'll be able to view the clutch and all of its components in its entirety.

Why the stupid background music? Made me seek this info elsewhere...

The best way to deal with a ski doo is run into open water and tell the police it was stolen problem solved