Single hole mixer sink taps leaking at base. How to fix it.
Тәжірибелік нұсқаулар және стиль
One of those leaks that is an irritation, as it leaves a stain on the sink unit.
Link for washer kit. amzn.to/2BLTfuX
Saved money on plumbers ? Donate here, using Al`s site link. www.dereton33.com/page118.html Thank you.
I also now have an Amazon storefront for all plumbing parts. It is www.amazon.co.uk/shop/dereton33
Пікірлер: 282
This is an awesome video. Watched it, watched it again, got the tools out, fixed my leaky faucet (that had really been driving me nuts). And I’m a 65 year old woman! Thanks so much!!!!
@dereton33
2 жыл бұрын
Great to hear!
@David-uk7sm
Жыл бұрын
65! Wow well done!
Thanks again for a well explained video. Just fixed my parents tap with your help. Wasn't sure how those taps came apart. Thanks again, your videos have helped me out alot in the past. Merry Xmas and a leaky free new year.
@dereton33
5 жыл бұрын
Have a nice Christmas Stephen.
thanks , dereton33 , i was struggling for 30mins to find out how to dismantle the unit until I see your vid showing me the secret tiny allen key hidden behind the plastic cover . Thanks Chief .
@dereton33
3 жыл бұрын
Glad I could help
Thank you very much for this video - it helped me carry out the task successfully: 3 factors helped: 1. The excellent video, even with a US faucet/tap with a couple of differences. The cartridge had the 2 little plugs on the bottom to align and the hot/cold rotator thingee that goes on the cartridge also had 2 plugs to align on the cartridge itself. Also, there was no o-ring or washer inside like in the video, but after taking everything out, cleaning all the parts and putting them back in, the leaking stopped. 2. The tip from other commenters to use a rubber jar opener to loosen the ring. 3. Serendipity; I had some to squirt some WD40 in order to loosen the nut holding the handle in place, as I could not turn the Allen key at first. Also, I did not put back the top ring and screw in the handle nut immediately, just as well as I had not aligned the cartridge, rotator thingee correctly at first, so I adjusted, tried again and all was well. Then I screwed everything back in place.
@dereton33
2 жыл бұрын
Pleased you sorted it ok Micheal.
Thank you for your excellent video! I was able to repair our faucet (tap) by using a bit of plumbers tape to increase the seal between the plastic o-ring and the faucet, where it swivels at the base. Again many thanks, as it saved my engaging a plumber for what is truly a minor job that even I could repair in under 15 minutes.
@dereton33
4 жыл бұрын
Glad it helped!
@chaigtin259
Жыл бұрын
Thanks for your hint! I did the same thing here for the rubber seals at the base of my Price Pfister kitchen sink tap: I found that covering them with a few wraps of teflon tape also helped the overall faucet move more freely and also stopped some slight drips getting out. For me that was happening due to the interior of the cylindrical part of the faucet having become slightly corroded (with the chrome plating wearing off to reveal a copper surface underneath, so the rubber ring was probably no longer making nice even contact, allowing a few drips to squeeze out at the base of the tap when it was turned on). With the teflon tape added over the rubber seals, that slight drip when the tap was turned on stopped completely for me. As a plus, the faucet is also no longer stiff to move from left to right! So it seems like this simple fix is working great, thanks for the hint! Perhaps using teflon tape also makes the rubber seal last longer? There would be less friction within the cylindrical part when moving the faucet from left to right, so less risk of the seals getting "shredded". I wonder why more plumbing channels don't recommend using teflon tape over these rubber seals? Perhaps it helps increase the sales of the replacement rubber seals?
I'm just getting used to being on my own so this video was a real boost for me. Thank you.
@dereton33
3 жыл бұрын
No problem Vicki.
Excellent! I'm having trouble sealing my mixer tap, after fitting a new cartridge. Your video takes me on to the next stage of disassembly with more confidence! Thanks!
@dereton33
Жыл бұрын
No problem.
Thanks for the video. We used a rubber stubby holder to avoid scratching, worked a treat.
@dereton33
4 жыл бұрын
That`s a good idea Susan.
Thank you for your help with this problem. We have the same tap and hubby was averting the job because he thought you had to tackle the problem from under the sink. Now I know better and will probably do the job myself.
@dereton33
2 жыл бұрын
No problem
Unbelievably helpful. My parents tap has this issue and now I know how to fix it. Thanks so much. Will like and subscribe.
@dereton33
2 жыл бұрын
Thanks for the sub!
Thanks for the help! After watching your video, I fixed the issue! The problem was the plastic nut that holds the cartridge in place...it was pretty loose. I tightened it up and it seems to be behaving now! :)
@dereton33
4 жыл бұрын
That`s great pleased you fixed it.
Thank you for an excellent video which shows the insides of these sink mixer taps and how to take them apart. However, I must pull you up on one thing regarding the cause of the leak: It's not failure of the white washers/spacers that cause these types of leaks (some taps don't even have them). Instead, it's failure of the black o-rings which are at top and bottom of the swing tap section. If they fail to seal properly, water will come out from either the top or bottom of the swing section (depending on which seal has failed). As you point out, dirt is often the culprit and a clean out can fix such leaks.
@dereton33
10 күн бұрын
Thanks
Amazing to realise I’m repairing EXACTLY the same tap as you while watching your video. Same problem abs same solution. Thanks :)
@dereton33
2 жыл бұрын
You're welcome!
Thanks for this - couldn't for the life of me work out how to do it! And your an old Mod like myself - keep on keeping the faith!
@dereton33
Жыл бұрын
Thanks, you too!
Thank you for this video. I needed this to fix my elderly mothers kitchen faucet! ❤️🙏🏻❤️
@dereton33
6 ай бұрын
You are so welcome!
Thanks for posting. Been looking at the leak and wondering. Appreciate your help.
@dereton33
2 ай бұрын
No problem 👍
Thank you for this excellent video ... just noticed that our sink mixer seem to have a similar issue and now I know how to take it apart and what to look for.
@dereton33
2 жыл бұрын
That's great
Very clear step by step instruction. Thankyou
@dereton33
4 жыл бұрын
No problem Jason.
Thanks for the video got the job done now I’m in the good books 🙏🏼
@dereton33
3 жыл бұрын
No problem 👍
Brilliant video. Well done. Makes me believe i can now do mine. Only thing is, i dont have those tools 🤣
@dereton33
4 жыл бұрын
O well never mind.
Thank you for this wonderful video, its exactly what I was looking for!
@dereton33
2 жыл бұрын
You're very welcome!
Great video! You could try using one of those rubber jar openers. The ones that look like an oil filter wrench. It'll help with the marring
@pauliethebrit
4 жыл бұрын
Great tip
@sweetczz
4 жыл бұрын
Funny u mentioned that - i was doing that, too. Messed it up sadly lol. Still didn't work
@TheUnknown-wr7nu
4 жыл бұрын
Never even thought of that thanks worked great 👍
Just did this it worked thanks great videos over the years thanks
@dereton33
3 жыл бұрын
You're welcome!
Thanks for the lesson , I at least got an understanding as to the method required , no to put it into practise , I'm sure it'll work for me , cheers mate .
@dereton33
4 жыл бұрын
Good luck Kim.
Great vid mate and good simple instructions that anyone can follow
@dereton33
Жыл бұрын
Thanks 👍
Thank you so much for your video....I just fixed my tap 🙂👍
@dereton33
3 жыл бұрын
You're welcome!
After seeing the video, this will give myself some idea how to fix our leaking kitchen mixer faucet.
@dereton33
27 күн бұрын
Glad it was helpful!
The best clip I found. Thank you!
@dereton33
8 ай бұрын
No problem.
Great video , very practical . Helped me out . Appreciate it
@dereton33
3 жыл бұрын
No problem 👍
Brilliant thanks a lot, now I can do mine leaking at the top, and my girlfriends, leaking at the bottom. Lets hope that just cleaning up those threads works like yours did.
@dereton33
26 күн бұрын
Good luck!
Spot on help, thank you very much.
@dereton33
4 жыл бұрын
You're welcome!
Wow another great video brilliant thanks again
@dereton33
4 жыл бұрын
No problem.
I've just bought and fitted a new one it's leaking slightly from the top joint above the one yours was ... hopefully I'll have a look today and it'll just need that top nut tightening a bit Thanks for the excellent video Mark in Poole:)
@dereton33
Жыл бұрын
Good luck with it Mark.
I had the same problem with a similar tap. I used a strap wrench to avoid scratching the chrome with a spanner. As you say Al the top parts only need to be hand tight and the strap wrench worked a treat.
@dereton33
5 жыл бұрын
Thanks for the extra info Cliff. Hope you are keeping well.
@cliffcarlo180
5 жыл бұрын
No worries Al. Hope the two of you are also keeping well.
Great vid with heaps of information, thank you
@dereton33
3 жыл бұрын
No problem 👍
They make a wrench for car oil filters that instead of using a metal band to grip, they use an adjustable rubber band that fits any size. It's called a Rubber Strap Wrench. About £3 ($6).
@sweetczz
4 жыл бұрын
AHA! I knew there was something like that on the market! I asked the man in the hardware store and he said he didn't know of anything like that. I was at Harbor Freights and just looked up Rubber Strap Wrench and sure enough they sell them! Whether it works or not who knows. $5 in USA. www.harborfreight.com/rubber-strap-wrench-set-2-pc-69373.html?cid=paid_google|||69373&gclid=Cj0KCQjw-_j1BRDkARIsAJcfmTHQcug1dbQiLq3gVIjOPbp53EMeILtuOXwK9vi2mO4G2qyvuE3a5sIaAij-EALw_wcB
Life saver this guy
@dereton33
3 жыл бұрын
No problem.
Thanks very Good video👍👍opened it up and saw the inner element was cracked and has to be replaced
@dereton33
3 жыл бұрын
You're welcome!
Great video. It showed me that the base of the tap can be unscrewed so that the sealing rings can be reached and renewed. This is my problem. And I will fix.
@dereton33
3 жыл бұрын
Glad it helped
@1davidang
Ай бұрын
where'd you buy seal rings please?
Thanks for sharing
Thanks so much for this. really helpful.
@dereton33
2 жыл бұрын
You're very welcome!
Thank you.
excellent video it really helped me out
@dereton33
3 жыл бұрын
Glad it helped
Very helpful thanks. As you say good luck with trying to find the exact size of O ring & seals.
@dereton33
Жыл бұрын
No problem 👍
Thanks. I hope to save my parents the cost of a plumber by doing this for them.
@dereton33
3 жыл бұрын
You can do it!
Thank you so much!!!!!
Canadian here, with the exact same problem. I suspected both upper and lower leaks were the result of a build up of lime (scale). Out water in Toronto is very hard, 7 grains, I think, and we require water softeners to prevent the build up of scale inside kettle, clothes irons, water heaters, steam irons and shower and kitchen faucets. The O-rings no longer made a complete seal with the build up of scale on them
@dereton33
Жыл бұрын
Limescale is a tap destroyer. We have hard water in London and the south east.
Silicon grease is very good for using with 'O' rings instead of plumbers mate, less messy and I found it a 100% perfect solution to seal and does not affect rubber 'o' rings.
@dereton33
Жыл бұрын
Thanks for sharing
For the rubber seal at the base, I found that covering it with a few wraps of teflon tape helps the overall faucet move more freely and also stops any slight drips getting out (sometimes that can happen due to the interior of the cylindrical part of the faucet having become slightly corroded with the chrome plating wearing off to reveal a copper surface underneath, so the rubber ring is probably no longer making nice even contact, allowing a few drips to squeeze out at the base of the tap when it is turned on). With the teflon tape added over the rubber seal, that slight drip when the tap was turned on stopped completely for me, and also the faucet is no longer stiff to move from left to right, so it seems like this simple fix is working. Perhaps using teflon tape also makes the rubber seal last longer, as there would be less friction within the cylindrical part when moving the faucet from left to right. I wonder why plumbers don't use teflon tape over the rubber seal?
@dereton33
Жыл бұрын
That stuff will not last long, we plumbers hate having to go back to jobs
@richardkroll2269
Жыл бұрын
@@dereton33 Thanks. I have an over 20 year old faucet and struggled with that leak, though slow, at the bottom and discovered that large ring was broken. I got a kit but of course the bottom ring was a "mouse hair" smaller but I slipped it on;. No luck.
Very helpful, thanks very much 👍
@dereton33
2 жыл бұрын
No problem 👍
I'm back here again, my leaky tap is a bit different, it has a two 1/4 turn taps and I'm going to change the cartridges in those to see if that solves the problem. I can see the the cold one leaking quite a lot, and I have not got a "Round2it" till now its causing a puddle in that mess under the sink. I'm just hoping that a pair of new cartridges solves the problem as I dont want to have to replace the tap. Its a nightmare under there ... the kitchen was fitted by a pair of bodgers and one of them thought he was a plumber. So its a complete hideous mess of Polypipe and right angled joiners. But great to see your videos again.
@dereton33
4 жыл бұрын
Good luck with it Tony.
@TonyEarlsTrinityLawns
4 жыл бұрын
@@dereton33 Yesterday was not a good day .. everything I touched came back to bite me. I ordered a couple of cartridges from screwfix but they were not the right ones when I picked them up. I was studying the original valve in my van, when I dropped it from my hand down the back of the seat in my brand new Transit. Ollocks! I could not reach it, I was in Stevenage and I was nowhere near home. I had to source one of those flexible grabby things .. I ordered one from Tool Station ... Got there ... no they didnt have one in stock. But! There was a very helpful plumbing supply next door ... So I bought another couple of cartridges that looked right. (from photo) + a complete new tap with flexi hoses and olives etc just in case. I managed to get a grabby think from Letchworth Tool Station and rescued the original valve in a jiff. Back home .. They still were the wrong valves :( My luck changed this morning when I went down the road to my local plumb shop (I don't know why I didn't go there first) And they sorted me out, not exactly the same ones, but good enough. Went home and changed both cartridges in 5 minutes. Thanks for your video and I would underline that there are only about 50,000 different cartridges out there to choose from.
Hi Al. I have a single lever valve tap for the hot & cold on the bath. It's leaking from the underside of lever part of the tap that moves up & down, left & right. Could that be a seal as well or could it be the cartridge? No brand name on the tap itself so I presume it'll be impossible to get the replacement parts.
@dereton33
5 жыл бұрын
It will be a washer seal on the cartridge. As you say it will be impossible to get a replacement.
@stanfitzpatrick6245
4 жыл бұрын
@@dereton33 replacement cartridges are available but they come in a variety of sizes. Take your old one for comparison. or if you buy on-line, compare sizes
good video thanks man
@dereton33
5 жыл бұрын
No problem.
Top job !!
@dereton33
5 жыл бұрын
Thanks PB.
Excellent Video.
@dereton33
3 жыл бұрын
Thank you very much!
You can definitely get the seals and cartridges. Local plumbing suppliers have them even some general hardware store's. Helps to know the model number but most are standardized.
@dereton33
Жыл бұрын
Thanks.
Hi, I have a similar leak but is not going into the cupboards underneath the sink also from the tap. , Do you think this process will help?
@dereton33
5 жыл бұрын
Worth a go.
I can't get the base piece on the faucet neck to turn. I sprayed w-40 and let it sit. I have the perfect curve jaw wrench that locks and I can't get it to budge to loosen the thread. Any advice?
@dereton33
4 жыл бұрын
Some models do not split and if yours is one of those, new taps is the only answer.
Very good video on disassembling a tap. Correct me if I'm wrong, but to me the white nylon washer looks like a sort of bearing ring that facilitates the tap rotating. I don't think it seals the tap. If the blue layer of the cartridge makes good contact no water should ever get as far as the white ring.
@dereton33
6 ай бұрын
Thanks for the info!. You could be right.
Thanks! Missing the gasket but fixed our leak 💧
@dereton33
Ай бұрын
No problem 👍
Well done
@dereton33
5 жыл бұрын
Thanks Amen.
This is wonderful...I appreciate the detailed explanation for a layman (or woman) such as myself. I have a question though please since I do sometimes have bad luck when I'm full of good intentions and have the confidence to attempt repairs myself ..You said that it would be very unlikely to find a washer "that size"..so in that case what should I do ? I think that that may well be my problem. The tap is about 2 years old and leaking from the base constantly. Hope to hear back Thank you and Cheers from Canada 🇨🇦. 🙂
@dereton33
3 жыл бұрын
You can try local plumbing stores in Canada, or just good old Amazon. There are so many different types of washers you may end up with ones that do not fit.
Great job👍👏👏👏
@dereton33
3 жыл бұрын
Thank you! 😃
Thank you so very much 😊❤
@dereton33
2 күн бұрын
Thanks for your kind donation.
@xAylaJx
2 күн бұрын
@@dereton33 I would've given more considering you possibly saved me hundreds of $ on hiring a plumber 😅
Thank you very much, i have the same problem on my mixer tap.
@dereton33
3 жыл бұрын
You're welcome!
@robby188
3 жыл бұрын
@@dereton33 i subscribe to your channel 🙂
Brilliant, thanks a lot, i wasnt sure if i should undo the chrome ring or whether it was part of the lower body. Right, wheres them grips
@dereton33
Жыл бұрын
Glad it helped
Great video, thanks.
@dereton33
Жыл бұрын
You are welcome!
I , being a window cleaner, use old squeegie rubbers when gripping any chrome with spanners etc. protects the chrome and actually grips better too.
@dereton33
3 жыл бұрын
Thanks for the tip.
Great video same problem thought it was the pipes but same problem
@dereton33
10 ай бұрын
Glad it helped
Hi Great video BUT I have removed the cover and then I cant find a hole to insert the Allen Key. Used a torch to look but there appears to be nowhere to insert the Allen Key into. I have rotated the handle so the hole is looking at different parts of the inside but luck in finding a slot for the key. Surely there must be something holding the handle in place?
@dereton33
7 ай бұрын
It may be just a push fit one, try pulling upwards. If no luck try tapping it upwards with a light hammer. Make sure the hole is not covered by a chrome cap, or hot or cold dot.
Hi under my kitchen sink there is ony 1 flexi hose its a combi boiler do you know what kind of tap i need to buy I bought second hand kitchen but on that sink it has 2 connections on the tap
@dereton33
3 жыл бұрын
If you just have cold then just plug off the hot side.
Thank you very mutch great video...!!!
@dereton33
10 ай бұрын
You are welcome!
Thanks for the friendly help there! I really wish we had some form of shut off valve for our hot water, it looks like I’m going to need to empty the whole cylinder before I can get in to check out these o-rings. How common is it these days to install shut off valves on each faucet in a home? I feel like that would save a lot of sanity being able to just isolate before a tap haha
@dereton33
8 ай бұрын
It is a common thing these days.
I need help with my kitchen taps? I want to change my 2 kitchen taps, for, 2 leaver taps I have looked for a tutorial on you tube, but, can only find kitchen mixer tap demonstration. ???
@dereton33
Жыл бұрын
Same job for them as single taps.
Thank you. Saved me $sss
@dereton33
4 жыл бұрын
No problem Colin.
Legend, thank you.
@dereton33
Жыл бұрын
No problem
Good video thank you
@dereton33
3 жыл бұрын
No problem 👍
Hi - excellent video - I have exactly the same leak and the same dirty parts - what did you use to clean the black marks around the washer and thread ?
@dereton33
5 жыл бұрын
WE 40
@dereton33
5 жыл бұрын
Oops WD 40.
@Flexb123
5 жыл бұрын
atleast his leaks back into the sink lol mine is on the counter basically. Found the water first underneat the sink, dripping right from faucet area , but then noticed its the actual faucet leaking at the base and water running down from the counter top basically through to bottom. Luckily it wasn't that much water and have it contained, watching this video though because it seems no plumbers around here want to work a small job so now i'm scared i'll have to try my unskilled self to fix it. I always scared to make things worse! lol
Thanks 👍
@dereton33
4 жыл бұрын
No problem 👍
Thank you for the video. That was really gross at the base. Is that mold or bacteria or what?
@dereton33
4 жыл бұрын
Probably both.
Very useful. Ours seems to leak from the same place, but the base ring of the tap becomes loose as there are not enough threads on it to hold it together through use. Very annoying!
@dereton33
2 жыл бұрын
Terrible bad quality of taps these days.
Good show 👍
@dereton33
3 жыл бұрын
Thanks 👍
I tried this but no screw visible to extract? Are there different types?
@dereton33
5 жыл бұрын
Yes some just pull off.
@benjaminnavarrete5150
5 жыл бұрын
I thought the same but If you look a little closer it could be a very small allen wrench
Thanks for that… I’ve a similar leak to check out, and bought two cartridges of different sizes yesterday. The kit had the Allen key and other o-rings etc included. BTW, I’ve heard your footprints wrench called multi-grips or a Stilson wrench in Australia (mistakenly) thanks for the vocab boost. Not sure what Boss white is? Lithium grease?
@dereton33
8 ай бұрын
Kind of, it just works well on belt and braces type leaks.
Hey, Al! Just out of interest. What hat is your most hated tap design, repair/service? I had a problem with a glass bowled, mono, lever, waterfall bath tap. Could not for the life of me get the chrome top screw plate off to get to the cartridge. The blessed thing was seized tight and the angle of the glass bowl frustrated me no end. It dripped for ages, but that was the start of the problem. The flexis supplied in the box were about 500mm long and were tightly bent over in the packaging and strapped tight with an elastic band. I reckon the rubber inner was stressed/fatigued being held in a kinked position during transit (probably all the way from China) Eventually perished, fine misting spray through the metal braided outer sheath. Even worse. The tap was located 1/2 way along the back, long length of the bath and both ends were butted against end walls. Had to cut plasterboard off bedroom wall on other side to get to the darn thing to swap it.
@dereton33
5 жыл бұрын
I had the same tap in the same position on my bath, the flexis also leaked on mine luckily, I was able to get under the void underneath the bath and replace them. By the way I think they are the worse taps to repair. Never again.
Like you, if this was on my own tap I would have a go at repairing it because I'm a tight arse. But as a jobbing plumber if I tried this for a tenanted property and it failed again within twelve months I would be expected to go back free of charge to resolve it so I don't bother and would replace it.
@dereton33
3 жыл бұрын
Best bet.
Mine leaking at base. But when I put o ring back on plastic piece it pops off when put base back on
@dereton33
4 жыл бұрын
It will need a new washer kit. Try Amazon.
I've got the seal kit, I've got the cartridge out - but I cannot get that chrome plated part to budge. And I don't want to scratch it !
@dereton33
7 күн бұрын
Try some WD40
@fastbike9845
7 күн бұрын
@@dereton33 Unfortunately the water from the hwc is slowly seeping in so i can't get it dry
Im in Home Depot, what's the name of the tool used? What type of wrench?
@dereton33
4 жыл бұрын
I have a link to the right tools, but a basin spanner is the one.
Mine is slightly leaking only at the base, where it meets the sink top. No water dripping down from higher up. What might cause that please? P.s. under the sink everything is bone dry with the lines nice and tight.
@dereton33
5 ай бұрын
Cartridge bottom washer leaking
Excellent 👌👌👍👍
@dereton33
6 ай бұрын
Thank you! Cheers!
I’ve took the grub screw out but it won’t lift off no matter what I try? Any help please
@dereton33
4 жыл бұрын
WD 40 and a tap upwards with a hammer.
@mnl493x
4 жыл бұрын
dereton33 thanks got there in the end was well stuck
There is a simple tool called a strap wrench you can use to loosen/tighten the chrome bits without marring them. It's one of the oldest and most useful tools out there.
@dereton33
Жыл бұрын
Thanks bruce.
I have a single center, kitchen tap that you lift a lever to turn tap on, left for hot, right for cold. It leaks from the inside of the ball that tap handle moves on. There is a tiny hole at front of tap that I am unsure if that unscrews tap handle. It's rusty af, so I have no clue. Does that part have a washer that I can replace, or do I have to get a whole new tap? ANYONE.??
@dereton33
Жыл бұрын
That tiny hole hides an allen key screw, which once loosened off allows you to take the top off. Unlikely you will be able to fix that leak though so I would recommend new taps.
@fadetoblond
Жыл бұрын
@@dereton33 Actually, the 2 O-rings at the base were all stretched out and cracked. I went to the hardware store and got replacement ones. I cleaned the tap parts of the mineral deposits, put it back together and it seems to be working fine now. No leaks. Fingers crossed that it stays fixed, at least til after winter. lol - Thanks so much for responding to me. Videos work wonders. I'm a half assed handywoman. 😂
😊thank u karau
@dereton33
9 ай бұрын
No problem.
Can you let me know how to take the dot off on the tap the bit before you need am Allen key
@dereton33
4 жыл бұрын
Hi Katie, it has to be prised out with a sharp pointed small screwdriver.
@katiefishwick7226
4 жыл бұрын
@@dereton33 thanks so much. Having looked under sink water is dripping down a pipe. Any advice on how I can fix this would be great.
@dereton33
4 жыл бұрын
Hi Katie, it is probably one of the small washers that seal the flexi pipes to the tap. Without proper tools this is one for a plumber.
@katiefishwick7226
4 жыл бұрын
Ok thank you so much
Silicone grease which is waterproof is great for lubricating and sealing joints like this.
@dereton33
3 ай бұрын
Thanks for the tip.
PERFECTO 👍 SEÑOR
@dereton33
4 жыл бұрын
Thank you.
what do I do when the alan key screw won't move?
@dereton33
2 жыл бұрын
Spray with WD 40 leave over night. If no joy, then drill it out. Use a larger self tapping screw to fit back.
Mine's a brand new tap. Could it just be that loose bolt on the top?
@dereton33
Жыл бұрын
Unlikely.
@ghengis430
Жыл бұрын
@dereton33 that isn't very helpful!