I'm making my first rc plane project from scratch and this video is just what I needed!

@klauss007007

Жыл бұрын

Same for me. I was looking for the two motors.

@sennestevens9196

10 ай бұрын

Same for me. I was looking for the 4 motors for my boeing dreamlifter that I am building from scratch!

@nathanholy

9 ай бұрын

Same for me, I have experience flying, but not building. I’m making a twin motor plane with a 70 inch wing span. Almost finished with the wing.

This is very good. You made the topic simple and easy to understand. Thank you

Thank you for this video I can now connect up my Hangar 9 B-25 using two batteries with two ESC’s without worry, excellent video!

So incredibly helpful, thank you!!!

I've been looking to make a multi-motor/esc project this has an excellent explanation of the process and options. I haven't been able to find any literature that wasn't 20 years old on this subject , or that didn't give erroneous cautions or methods that just didn't make sense. My local hobby shop actually looked at me funny when I mention what and how I'd like to go about my project, you know like dogs do when they aren't sure what's going on. That was my big sign to find information else where. If you ever do turn this into a document I would gladly store it away with all the other articles and books I have on these subjects

Good to see you again

This is really helpful. Thanks for sharing!!

excellent video thanks, very helpful and to the point with no bs and real world example :)

Nice bench set up, might also mention calibrating the escs all together.... (In something like a twin it's important to be getting relevant thrust from each side.)

Thank you. Very helpfull video.

Great information. Keep up the good work.

Awesome video 👍 Thank you 😄

Thank you for this!

Very interesting, many thanks.

Thanks, very helpful

thanks for the video, yes I encountered a problem... one engine starts before the other.

Legend

I'm going to use multicopter escs now. They are smaller and lighter but don't have a bec. For that application i use a multicopter pdb with integrated bec where i can solder on up to 8 escs depending on your board. Now i only have to solder on a single battery connector and that's it 😉

Thanks for explanations. Just subbed to your channel..

Great video! quick and easy to undersand. Will you make another one with differential throttle in the future?

Maybe also worth mentioning that the colors on the 3 motor wires are not relevant - in case people have motors/esc with single colored wires. And maybe also to check the current drawn by multiple motors - make sure the battery can handle it if you use 4/2 motors on a single battery

I was wondering if that's possible, now I know thanks.

Nicely done , thank you. If you want to power two motors on one bigger battery, do you mean more volts or more amps ? Both ? Can you plug à 6s battery to 2 escs accepting 2-4 s lipo without burning them ?

Good simple description. If multi-motors are connected to separate battery packs, one weak battery pack may result in one ESC going into low voltage cutoff and one motor cutting out. Using a single higher capacity battery pack may have some advantages in smaller models.

I prefer leaving the ESC plugs intact and remove the power ("+") contact(s) from the Y harness(es).

Would the main running one for the servos and all, would it go flatter quicker. Thanks

Hi, thanks for the video, excellent. I'm busy building my twin electric model. The twin system necessitated (or so I thought) in extending the leads between the battery and the ESC. I'm told this is incorrect and I will be in trouble; the ESC won't work properly, I should installed a capacitor just before each ESC. The leads between the ESC and the motor should have been extended. My leads are ~600mm long. How did you solve this problem on your multiengine planes? Would appreciate a comment.

I really appreciate this video and I tried to recreate the same thing. However I am having trouble only one of the two brushless motors is running. I have 2x40A ESC and 35c/2200mAH battery. Any help would be greatly appreciated

hello Troy, Have you seen the new LW-PLA FW-190 Eclipson model? Will there be your build video and test?

Do you have your settings anywhere for the Flsun v400?

Is it possible to leave the power wire in the other esc? I'm thinking it be OK since it's in parallel, it would also act as a redundant if the other esc were to fail.

I'm experimenting with a Stock twin prop 550kv set up. 2x 40A esc, 1x 6s lipo and the max Amp draw is 62A. I'm assuming this is over the 2x ESC combined so my ceiling is 80A. However if I'm going to use 2x lipos I'd certainly not use 2x 6s lipos. The power of the 6s is shared with the 2 motors. I feel if I was going to go dual lipo I'd use 2x 4s lipos. (These motors are 4s rated in 4s planes and 6s for 1 motor would surely be into the 90A+). My question is how do I work out the RPM of each motor in my set up? How much voltage do I know each motor is getting on 6s set up? My aim is to change out the motors to 750kv hoping my stock 40A escs are within operating limits. Cheers

If you are using a dedicated receiver battery that is separate from the flight packs do you disconnect all 4 of the power wires from the ESC’s since the rx is being powered by its own battery?

@kilroy07

8 ай бұрын

Yes

Yo what is the name of that wire harness

...😜👌

:15 four GAS props really?

I saw all aircraft you build ..im your subscribers from Philippines..im also love doing drone ang aircraft.....i have diy drone but its broke..ang now i want to build aircraft..help mo for needed materials thank .. I hope you read this massage

I did it differently..I hooked up one big esc and branched each of the wires coming off it into two. Seems to work okay, but is this going to cause damage in some way?