Simple LS Swap fuel system for a C10
Автокөліктер мен көлік құралдары
#c10 #lsswap #chevytrucks #squarebodychevy #chevy
hotrodfuelhose.com/?gad_sourc...
Return less Kit
hotrodfuelhose.com/products/r...
Fuel Sending Unit
hotrodfuelhose.com/products/s...
Fuel Pump
hotrodfuelhose.com/products/w...
Fuel tank
hotrodfuelhose.com/products/c...
Пікірлер: 46
Awesome video man, This is hands down the most simplest video I've watched & i have watched many. Appreciate the straight forward approach no bs talking.
@3rdGenC10s
6 ай бұрын
I appreciate it glad it helped you out!
Thanks for posting this! I coming from you’re other fuel system video! Great work man!
@3rdGenC10s
6 ай бұрын
Hope they helped you out!
Great info!
@3rdGenC10s
2 ай бұрын
I appreciate it!
Nice video!
@3rdGenC10s
2 ай бұрын
Thank you!
Its amazing how much you sounds like David Newburn from Faster with Newburn and Cotton
@3rdGenC10s
2 ай бұрын
One of my favorite shows to watch!
Thks for the video
@3rdGenC10s
2 ай бұрын
You're welcome
Would have been good to see what the niggle was with the AN fittings. You can bet someone else gets the same problem and wont get the solution from someone who solved it.
@3rdGenC10s
8 ай бұрын
I cut it to close the the factory beveled portion which swelled the tube changing the OD of it.
I used an fittings on mine but i used a different style. Didn't have to cut the end of the feed/return line
@3rdGenC10s
4 ай бұрын
Right on!
@mcgarijs
Ай бұрын
whats the part number of the one you used
Great video but Did you have to cut the bevels off the get the fittings on because I'm having the same issue
@3rdGenC10s
3 ай бұрын
Yes they have to come off for the fittings to work.
Do you have a part number for driver side?
@3rdGenC10s
Ай бұрын
Tank or sending unit?
Can you just use braided kevlar hose with clamp over the fuel lines or do you have to use AN 6 lines
@3rdGenC10s
Ай бұрын
Im not sure on that. I would assume you could use clamps but idk know that answer for sure.
great video!! what did you tie your power and gauge wire into to give them power? did you have a new fuel pump relay harness or did you tie into something factory on the truck? i have an 85 c10 and looking for power sources for my swap
@3rdGenC10s
2 ай бұрын
The stand-alone harness I bought had a fuel pump relay to tie into for fuel pump power and I used the factory fuel level sending wire.
@khoryhadnot
Ай бұрын
@@3rdGenC10swhat stand alone harness did you buy do you have Link
@3rdGenC10s
Ай бұрын
@@khoryhadnot PSI
Why was my gas spewing out of the vent tube from the sending unit it did after my truck was warmed up after I loosened up the gas cap it stop spewing fuel
@3rdGenC10s
8 ай бұрын
Sounds like it’s pressuring up. Might try buying a vented gas cap.
Where did you get the rubber "isolator" material for the tank straps?
@3rdGenC10s
Ай бұрын
Previous owner put it on, I’m not sure where he got it.
I just put a 86 305 engine/700r4 trans in a 1997 suburban 1500...should i replace the fuel pump in the tank with a 86 style fuel pump im stuck on how to run fuel lines to my carb..engine also came with a Posi flo electric fuel pump hooked up to the carb...motor is from 86 caprice
@3rdGenC10s
Ай бұрын
I’d put a in tank pump if it doesn’t have provisions for a mechanical on the block.
I’m putting an L 86 LT engine in 1986 K-10. Did you need to modify or change the fuel lines leading up to the engine bay? My stock set up was low pressure mechanical pump. I’m assuming the 87 was much higher pressure electronic
@3rdGenC10s
2 ай бұрын
87 is only 12-14 ish psi 3/8 feed hardline and 5/16 return lines is pretty standard for a ls swap
@jasondominguez8179
2 ай бұрын
So did you just use the 87 fuel lines? I'm not doing LS on my 87, but doing a edelbrock pro flo 4 and it calls for this style pump. My question: is the factory fuel lines on my 87 with TBI acceptable for the pressure od the wabro 255? Or should I be looking to replace the hoses?
@fatkat311
2 ай бұрын
@@jasondominguez8179 The stock fuel lines didbnot work for me. There were some rubber hoses in the system that could not handle the higher pressure. I had to install a new sending unit and fuel lines.
Wonder if this will work for my 77 Monte🤔
@3rdGenC10s
6 ай бұрын
Everything but the fuel tank should work for you.
Are you going to put in a drivers side tank?
@3rdGenC10s
7 ай бұрын
No, bed only has a filler neck on passenger side.
Can you give me the part number of the fuel pump base?
@3rdGenC10s
3 ай бұрын
Driver or passenger side?
@HectorLopez-gn5sl
3 ай бұрын
Passenger side
Can you make a wiring video
@3rdGenC10s
5 ай бұрын
I’ll try and get one made when I get to that point