Simple how-to: Change headlight bulbs, Mazda 2 [Demio]
Автокөліктер мен көлік құралдары
Easy DIY how to: replacing headlight bulbs on a Mazda 2 (AKA Demio) (2nd generation "DY") 2002-2007. This is an easy job with simple access.
This car uses H4 bulbs which combine low and high beams into the one bulb on each side.
You will need:
* New bulbs as required: 2 x H4 / 9003 (replace in pairs) - Amazon US: amzn.to/2aFFek1 | UK: amzn.to/2crDpbt
* Latex gloves (ideally)
* Flashlight.
(Using the above Amazon links will help support my channel and is appreciated!)
Пікірлер: 66
Amazon links to relevant products are in the description.
Thank you for this! Both my headlights were dead and I just fixed them myself - definitely see where lady hands are an advantage.
I just changed the bulbs on my GFs mazda 2. This vid was helpful. Thanks for posting. I had no luck getting the plug off the back initially. What I ended up doing, was just pulling the rubber boot back enough to reach in, undo the spring clip and pull the entire connected plug/boot/bulb assembly out. Then I had plenty of leverage on the plug and disconnect.
@RobinHoodTragic
Жыл бұрын
Thank you for this comment. I was also struggling to get the plug off the pins and this is what ultimately helped me
@baardmannetje9339
5 ай бұрын
@@RobinHoodTragic same here
Thank you, i have just changed my bulb following your tutorial.really simple.
Changed in less than 5min. My first car bulb in my life. Very good tutorial. Thx bro.
@mauricelelemurien7490
2 жыл бұрын
I will too, so useful 👍
Extremely helpful. Thanks. 👍
I didn't know that it's so easy !!!! :) Thank you!
Thanks a lot. Great voice!!
Thanks mate, very well explained .
Thanks done this on Mazda 2 before ,but it's nice to know before doing it again (the left side is harder with the fuse box in the way (2012 NA left side steering) if you look at Mazda manual they want you to take half the car apart .
Thankyou , saved me !
Thx for this video
So helpful for me. Thx !!!!
Bit harder with big hands but got it done... Thanx 😊
Cheers buddy, local garage wanted to charge 8 quid!!
Thanks Craig, nice clear and simple instructions...perfect
Thx your Help me nice video:)
My Mazda2 has separate low and high beams and its a PITA to change low beam bulb, which is H7
thank you
Thanks just did it found it difficult enough,no room but all working.
perfekt thanks. gonna try this today :D. wish me luck please :)
Yea right 😅😅 make a video doing the left side bulb . The right side is easy and fast like in video . You have to loosen part of the bumper and pull the light unit out and , only then do you have access to the left side bulb . Ive just replaced my standard H4 with high performance 5000k blue white . I had the same problem when I owned a 2004 Mazda Axela . I high intensity bulbs in the Axela . Had to remove part of the bumper to change the right side bulb . I owned a S14 Silvia for 11 years . That took the H1 bulb and didnt require loosening part of bumper
Love you
Please please do asmr. Your voice 😍😍😍
Hello, how do i replace the little ones the middle ones. thanks for the help
Thank you for taking the time to upload this. I am in the process of upgrading to LEDs in my '01 Protege, and found the headlight assembly to be very similar to this vehicle. FWIW, I rebuilt the front end after an unfortunate incident, and have aftermarket lamp housings. The type of bulbs I purchased have a heat sink and cooling fan, and that rubber boot on the aftermarket assemblies completely restrict the airflow needed to make the fans do their job. I am going to have to modify the length of the factory boots (which fit on the aftermarket lenses) to accommodate the 1/8" of difference between the halogens and the LEDs. Despite that setback, your video was very helpful in showing just how these things come apart. Thanks again. P.S. - it was that clip that I've never encountered before that was giving me the most trouble, as I was working pretty much blind and had not encountered that sort of retaining mechanism in a headlight before.
I seem not to able to get the plug off on my 2001 mazda protege please help wat the the best way to get it off
Thank you - very helpful - much appreciated
Is there a video for brake light bulb same car?
thank you! Clear demonstration, going to try tomorrow morning!!
The plug is hard to remove, afraid to break it
@mzn9612
Жыл бұрын
Yeah I am stucked in that part.. I couldnt take that out
I saw this video and it looked very easy but I was struggling, so I went to the garage and they couldn't do it either. I believe it's the original factory bulb and it really feels stuck. It's going back tomorrow so they can have another go.
@Kenst9988
3 жыл бұрын
Ki n Nb b....... b. Sd6b vvv
@Kenst9988
3 жыл бұрын
Io in. 7n,no ,wonder ,,no. B7iknb. .
@Kenst9988
3 жыл бұрын
Vic cc mm 6 cc
Can you please show us how to do this for the brake lights?
@JohnLawley24v
7 жыл бұрын
Zombie Rofl this. I'm stumped as well
bro! how can change de lights of dashboard? (RPM,Velocity,Fuel,eetc...) for my mazda demio 2004
I have way to big hands for this job, so i went to my mechanic, and he did it under 2 min, i ask how much it would cost me, and he said nothing :) (had the bulb with me). but i said i though he should have something for his trouble, so i ended up paying he 50 Dkr or around 8 Us dollars
@CraigsDIY
6 жыл бұрын
That's one way to do it.
And rear lights? Make a video ty
You should probably mention that if you let go of the lamp whilst attempting to position it, it can fall inside the enclosure - which presents you with a whole new problem ;-)
Hi, how I can replace stop bulb on my Mazda 2 2004 (not seen any screw ), please anyone ?
@JohnLawley24v
7 жыл бұрын
Sasa Marjanovic following as I'd also like to know this.
@kristinacurcic9602
7 жыл бұрын
Sasa Marjanovic jesi saznao kako? Meni isto treba ta pomoc.
@sasamarjanovic1837
6 жыл бұрын
Mora da se skine bocna plastika (ima zabice i srafove) i donja plastika oko brave da bi se doslo do kucista sijalica, Pozdrav
Can't get the plug off
too scared to show the right bulb? you have to break your hand or be a child to do it on the 2003 model
@myusername
7 жыл бұрын
Try it on a Demio 2000 model! It took me half hour to place the lamp in and I'm still not done (That's why I'm looking on KZread for tips). How the F can u put the clip back on? The light was insane but the clip is on another level insanity! Here's a image: preview.netcarshow.com/Mazda-Demio-2000-1600-1c.jpg Can I remove that pipe or is that stupid to do?
@Souls4Roca
7 жыл бұрын
TheTunzy the clip or the rubber? the clip is the easy, it's like a door, you push, while pushing , push it down and it should lock
@Souls4Roca
7 жыл бұрын
TheTunzy for the pipe I recommend pay the extra and take it to the mechanic
@myusername
7 жыл бұрын
I got it on with the rubber, but it's just the clip that I can't get back on. I tried it again and now the clip fall off. I watched some other video's and the clip is behind a screw. Maybe it's better to just get the whole lamp out now?
@jarrado1
5 жыл бұрын
I have a Mazda demio 2006. Just found that out. Is it easier to take it to a professional?
I can't even get the bonnet open
Here's me can't even get past the first bloody step 🤦♂️
You forgot to mention not to touch the Glass *
Falscher Film für Scheinwerfer tauschen gezeigt
The most important, and hardest to figure out, is the removing the spring clip.The video does not show this at all, basically worthless instruction video.
Hahaha. You're a fraud. You chose the easy side. Other side has much less room and needs the bumper removed if you don't have tiny hands.