I just want to say I usually don’t watch 7 yer old videos. But your the only one who could explain the power unit that you used and the solder and connectors. I want to thank you for the simple instructions. Make a new one or repost this old one. ❤❤thank you

Going to be redoing some wiring on my layout in the future so I caught this video at a great time. Thanks for sharing Chris. -Ethan

I’m new in trains I love your video!

Great concise video.

nice job, I place a drop of super glue into the fork or spade connector before the crimp, then crimp. So far good power flow and they do not come undone.

Very nice, similar to mine but not soldered. I guess that’s my new project! Thanks.

Great info 🚂❤️👍👍👍👍👍👍 🎆subscribed 🎆

What is the max amperage you can pull from this wiring set up without risk heating those terminals, I take it is consistent throughout the layout.

Where do the wires from the the orange post and the black post go to on a train transformer (American Flyer 18B - 180 watts)?

Nice video!, really learned many things from it. Just want to ask if this star method recommended for MTH could work as well for Lionel TMCC? I tried bus system technique but the signal is not strong enough. Believe because I shared the ground cable with many accessories switches, etc made branches with it. I planning changing it to the star method to enhance signal. Any suggestions?

@PrimeMoverVideos

5 жыл бұрын

I had added Lionels Legacy system by just connecting to the input terminals on the TIU with no other changes and it worked perfectly.

@PrimeMoverVideos

5 жыл бұрын

I also have the track ground isolated from anything else like switches and accessories.

@juanarturofernandezn6491

5 жыл бұрын

Many thanks; I'll then isolate the ground line for the track from the common ground I use for accessories, switches, etc. So make a star arrangement connection just for the track I will come back to you with other arising issues if you do not mind.

Great video! How did you attach wiring to track? Solder or Lockons? Just curious?

@PrimeMoverVideos

2 жыл бұрын

I soldered all the connections to the base of the rail.

@jsgtrains3176

2 жыл бұрын

@@PrimeMoverVideos I really liked your crimping. Goes to show that a person like me does not have to apply too much pressure that destroys plastic jacket

@PrimeMoverVideos

2 жыл бұрын

@@jsgtrains3176 No not at all. It's all a learning process. Give yourself time to learn, you'll make mistakes just as I do but you'll learn from them. Keep at it and I wish you a ton of success with your layout.😁

Hi ,question the red and black bottoms are those connected to the transformer?

@MrShain1611

Жыл бұрын

Yes, you can connect those to any transformer.

I have done as you have in the past. I've never used speaker wire.. I like the idea of it. I noticed that you chose copper for Positive and the aluminum for Ground.. what is the theory of this practice? I don't believe you just happened to do it this way.. there must be a reason for this method. Thank you for sharing.

@richardbrown3061

Жыл бұрын

Makes it easier to identify the positive from common or ground. Same principle as electrical wire in a house. There is some speaker wire that has copper on both leads and some that has silver on both leads.

@Mercatoyd

Жыл бұрын

@@richardbrown3061 thank you for the reply... really great video.

I hope you are still around to answer this: All the MTH, Lionel accessory/buildings I have come pre wired with a short length of very thin wire. It appears to me that you are using standard stereo speaker wire which is much thicker. AmI correct and,if so,how did you handle it- cut off what came with the pieces and start over with the clear wiring, thicker wiring ? Thanks !!

@PrimeMoverVideos

Жыл бұрын

Hello, I did use speaker wire however only for track power feeders. It works very well with DCS. I use much smaller wire on houses and structures. Thanks for the question and Happy New Year.

@flynnlizzy5469

Жыл бұрын

@@PrimeMoverVideos Thank you for the quick reply !! If you don't mind because I'm about to buy a lot of it, what size did you use for your lit buildings and houses ? I have about a dozen stores / Main St kind of thing, and some track accessories-lights and soon plus half a dozen switch tracks on an 'L' shape 5''x14' and 5' x 10' lay out. I have a MTH water tower too and that motorised train barn thats been popular (forgetting the maker. They send out these units with a short section of wire nd the wire is really between thread and string size. Do you pull out the thin stuff and solder in the new thicker ? I can't tell if they're just being cheap or its a tip from them as to what size is appropriate ? Seems REALLY flimsy though. I run a MTH Z-4000 with a Lionel remote wired into the Z for power. I'm just getting started. Thanks for any advice, really appreciate it !!

@PrimeMoverVideos

Жыл бұрын

@flynnlizzy5469 Gosh I think I used 20 gauge. Low amperage things like the houses or small accessories where the amperage is low do not require a large gauge of wire. I think MTH uses 22 gage but I'm not positive on that.

What is a TIU???

@PrimeMoverVideos

2 жыл бұрын

A TIU is a Track Interface Unit which is part of MTH's DCS system.

Very professionally done and explained. Thank you. I use Atlas like you, so much more realistic track.