Seven Course Block Lead | Prep and Construction | JATC Training
Our Apprenticeship Training Program shares a step-by-step tutorial on how to build a seven course block lead.
Жүктеу.....
Пікірлер: 129
@Heavensmyhomenow2 ай бұрын
Thank you for giving us this free valuable lesson many are sitting on school writing an essay of paying thousands of dollars. Taking it up to the 7th course we go the main point especially if you are a GC like myself
@muleleedward9642 Жыл бұрын
you are surely a great teacher and very neat in your work.
@everettlong2827 Жыл бұрын
This was great I hadn’t laid block in a while but it was a good refresher
@MatzeMaulwurf11 ай бұрын
Nice to see you are using a Stabila Level from Germany 🇩🇪😊 Does she like your freedom units? She is only familiar to meters and centimeters. At least rectangular angles are also 90 deg in the US. 😅
@thomasglessner6067 Жыл бұрын
Great presentation and followup before closing. You are a great teacher. Thank you for sharing.
@user-cl9dy6fc6o2 ай бұрын
Those look like some very well made block. I have seen some that your level would wobble on top of. Very hard to build a decent wall with trash like that but we did it every day. Good job. Good trowel, W. Rose always made the best. I also prefer the leather wrapped handle.
@davechez17582 жыл бұрын
brings back memories...I started my apprenticeship back in n1978
@user-cl9dy6fc6o
2 ай бұрын
I started in 1972
@brikkijim2 жыл бұрын
Overall good information but I would like to see a better head joint. Many masons will have a full head joint then ruin it by sliding it down. This removes most of it. A better way is to push into block because it compacts the mortar fully without dropping down. Just something I have learned over the years and wish I was taught that in the beginning.
@tonylinardi3089
2 жыл бұрын
Shove joints are the best joints!
@afrokidd214
2 жыл бұрын
Yes i wish some would tought me that but recently i was laying block with a old school so he schooled me on that cause i would leave gaps and double work went i had to joint and refill them
@ficknoti
Жыл бұрын
Not these days lol
@bradmason8334
10 ай бұрын
How would you construct this type of wall for superior strength for hind wind areas?
@brikkijim
10 ай бұрын
@@bradmason8334 Rebar every 24 inches filled core. From footing to the top. Bond beam every 4 feet in height with a bond beam at the bottom and at the top. Durawall in the bed joints every 16 inches. If possible plaster/stucco one side of block to reinforce the entire wall. This is for extreme conditions and obviously have temporary supports until all is cured.
@TruthSeeeker77710 ай бұрын
Thank you for your tutorial. Very helpful!
@constructionnew
10 ай бұрын
❤❤❤
@lubwamakeithjimmie2598 Жыл бұрын
Thanks for sharing your wealth of knowledge
@lihlemokgalaka6109 Жыл бұрын
Wow that was so perfectly informative 👌 and neat
@ManuelRioz-li1ps4 ай бұрын
Gracias por buen curso yo también soy blockero saludos desde Tijuana 💪👍🐓
@juancmartinez9042 жыл бұрын
Great job!!
@jabulanikhumalo81817 ай бұрын
What a good lesson.
@babacarsarr69019 ай бұрын
Watching from west Africa
@marlonramirez4832 Жыл бұрын
Gracias .Difrute y aprendi mucho con su video
@morganchetty7593 Жыл бұрын
Very neat finish. Thankyou for your ideas.
@formukongdieudonne5922
Жыл бұрын
I will be wanted to work with your company
@formukongdieudonne5922
Жыл бұрын
😂
@user-pi1je9hj2w Жыл бұрын
Nice work sir am impressed
@williamgibbs8400 Жыл бұрын
Is the tab wire needed if you are doing a straight wall without having access to the corner of the other walls. I assume this is for strenght.
@beckersworldinc.1717 ай бұрын
Corner blocks should always be checked vertically instead of horizontal with the level, best way to keep it going up straight.
@romygomez8423 Жыл бұрын
Thank you sir I learn your vidio❤❤❤
@lubwamakeithjimmie2598 Жыл бұрын
Awesome
@genollanas2110 Жыл бұрын
Is that wire between the courses for brick wall ties also?
@user-cl9dy6fc6o
2 ай бұрын
It can be made in such a way that a brick wall can be tied to the block wall. That type wire has loops on short wire that sticks out the side of the block. Another type wire is inserted in the loop and laid into the brick as you build that wall. Alternatively, you can lay both walls at the same time and put wider wire in every 2 courses or so. In that scenario you would use 12 inch wire for an 8 inch block wall with a brick veneer.
@bradmason833410 ай бұрын
How would you construct this type of wall for superior strength for high wind areas? Rebar & cement inside of block or something else?
@user-cl9dy6fc6o
2 ай бұрын
It is common, especially in commercial construction, to run a vertical cell full of grout with rebar at prescribed intervals. In prisons they often pour every cell.
@mipianseitaj55062 жыл бұрын
Thanks so much
@gavin_quirke2 ай бұрын
Thanks! Do you have to fill in the head gaps, for each level ? before the next level goes up. There is a hollow there I see, so wondering does that need filling also ? And secondly, would it be a good idea to fill the cavities of each block with mortar, or just a waste ? (have seen the vertical rebar cavities filled, but asking if its good practice regardless of rebar or not for overall strength ? Thanks again
@hbccbd Жыл бұрын
Good job
@sanaolvlog4 ай бұрын
❤❤❤❤
@zia2066 Жыл бұрын
A good idea would be to is nail a straight edge on the ground to your square line so to be sure that your block is layed on the line
@Steven-mm7gb
5 ай бұрын
can spray that chalk line with clear coat, will keep it bright and wont go away no matter
@mrrsnaconstruction27702 жыл бұрын
Very good 👍
@phoenixdepannage9103
Жыл бұрын
Hjtx
@ericgarlo534 Жыл бұрын
Thank you
@petermandona2490 Жыл бұрын
Nice ❤️
@zikirulaimusodiqkola69276 ай бұрын
Perfect
@crisfersonfragoso5507 Жыл бұрын
Top !
@vtreanor Жыл бұрын
Interesting thank you but, what on earth is tab wire. Google doesn't seem to recognise it nor can I find any trace of it here in Europe. What are the 2 tabs for?
@genepires9394
6 ай бұрын
its dura wall, galvanized reinforcement. The 'eye's' receive a tie for a veneer brick wall
@robbiegodsey56589 ай бұрын
Ever hear anyone setting the wire into the mud rather than spreading on top of the mud?
@romilsonsoares1199 Жыл бұрын
Top
@tonylinardi30892 жыл бұрын
Great video! I'm an instructor in Canada, are you looking for instructors?
@baclocal1mvd40
2 жыл бұрын
Thank you! If your are interested and open to relocation, please inquire on our website.
@constructionnew10 ай бұрын
🎉🎉🎉
@jimmyboy2844 Жыл бұрын
Your worth about 20 bucks an hr here in Calgary! I would have to yell at you all day with your work!
@ic65372 жыл бұрын
Fill head joints ?? Make sure they are packed ?? Clipping the block is not full
@deniscommins2 жыл бұрын
can you plumb from inside the wall instead of outside ??
@jimmyboy2844
2 жыл бұрын
Only plumb one side and yes you can plumb from the inside. Just pick one and stay with it!
@richardstetson8221
2 жыл бұрын
You still have to plumb the outside corner from the outside of the wall unless they are split-face block
@robertkiser8465
Жыл бұрын
Not building a corner wall..
@abdullaha3496 Жыл бұрын
what are these wires outside of the wall for?
@jareddaugherty84
Жыл бұрын
To tie it together with a brick veneer
@ohmygodwhatareyoudoing49292 жыл бұрын
Not sure what your blocks are made of but here in the UK our hollows are 26kg (over 50lbs) not sure I could lift with one hand, maybe your superman
@chadcornick4655
Жыл бұрын
Well this guy's abilities of spreading mortar is good for a laugh are blocks here in the US are typically around 35 to 50 pounds each more the 50 pounds any more it's stupid 3" split face side walls with some center web 3" and corner blocks can and do get around 4" the engineers that spec the blocks don't seem to grasp that steel with over lap goes in these blocks along with electrical and plumbing and the concrete and steel are what give it its true strength and limiting them is not all that smart. 55 to 65 pounds a block one handed is no problem even with high rebar all day long small cut up jobs I will average around 200 big jobs with long walls are easy and I enjoy laying 400 to 500 a day plus that includes stocking and rebar placement and grouting and I double joint all my own work and build most all the leeds for the guys
@orgesornespllana9656
Жыл бұрын
Q😮🎉🎉🎉🎉🎉
@user-ux2oy4hk4k11 ай бұрын
😊😊😊😊
@CheikhSeye-du2ie Жыл бұрын
🤙🤙❤❤
@greaternews0000 Жыл бұрын
I am interested, how can I enroll
@MA-vm6jl2 жыл бұрын
Hi. How long is course? Also is there any training like this in Los Angeles
@terrytodd5344
2 жыл бұрын
BAC Local 4
@robertkiser8465
Жыл бұрын
3 to 4 year apprenticeship, Then you can get your journeyman's card..
@hakimislam6218
Жыл бұрын
I started out in Los Angeles, BAC Local 4 now I'm BAC Local 4 in NJ
@zikirulaimusodiqkola69276 ай бұрын
Pls how can I join you to training me boss back in Nigeria I'm a bricklayer now I'm in London now working at site as a cleaner Reply me pls
@Panelson749 ай бұрын
Please order a quality camera, this one is very pixelated.
@jermaineallen2915 Жыл бұрын
I, hope he's building fish tank and not house because no hold drill for rebar as they call stell maybe this why some home cap size in earth quake they laid neath and he worked clean.
@maamicogondwe678924 күн бұрын
What's the size of a block plz
@hayblut4607 Жыл бұрын
I nice love
@jeanlouisjeandavid5799 Жыл бұрын
Aya papa📖📖📖📖📖📖📖📖📖📖📖📖📖📖
@aychewzegeye6385
Жыл бұрын
ቆንጆ
@v8pilot Жыл бұрын
Why do Americans lay blocks upside down?
@markmorgan6231 Жыл бұрын
ALRIGHT ROUGH UN
@alismith1320 Жыл бұрын
I think he would use 2 blocks to make a square, before a straight laying 🤫
@amandaweatherly905816 күн бұрын
Jointing the outside is unnecessary if you're using hook and eye wire.. other than that, good video.
@user-nd2zl6lm1t Жыл бұрын
Раствора маловато под блоком. Или вы потом бетоном заливаете. Для усиления стены?
@waltherheinrich
Жыл бұрын
Это школа
@waltherheinrich
Жыл бұрын
Это школа
@OneGrainYT Жыл бұрын
Never pass 3 else you will not get a straight wall. Your lever might be 4ft, but if you pass 2 and a half block out you won't get a straight wall.
@jimmyboy28442 жыл бұрын
Sloppy! But its not coming down. I rate you as a good second year apprentice. Work on that jointing and plumb your first course from the face of the block.
@thomasfyffe5192
2 жыл бұрын
Ok master block layer how is it sloppy?
@jimmyboy2844
2 жыл бұрын
@@thomasfyffe5192 Let me count the ways. First off, Its always a mistake to lay past a level. A level is only accurate to 3 mm. It says it on the level. So 4 blocks long max, Also, Plumb the face of the first course. Joint/pointing is attrocious. Dont just lay one block and then use the level. Soften your mud. The list goes on. Second year where I come from. Wire has been installed sloppy. Insufficient overlap left out and why would you use 2 seperate pieces? Thats just the lead, What other sloppy mistakes do you make on the wall to make up time? Because you didnt plumb the face of the first course, You more that the 3mm out on a level and wondering your whole life why. Every course is tipped the opposite way to correct it on the level. Mistake after mistake results in deficiencies.
@jimmyboy2844
2 жыл бұрын
@@thomasfyffe5192 Yes, I am a master Bricklayer!
@nl-ds2ov
2 жыл бұрын
Nobody's perfect.....
@mppetrikas4919
Жыл бұрын
@@nl-ds2ov Jimmy boy is
@kensterling52172 жыл бұрын
Damn, another Union Apprentice with a KZread video. #1 You Always Double Butter, did you forget that ?? And you level from side to side first then long ways. Get a better level. With all these Union Halls just letting Anyone in, because of Dues. No Wonder Real Craftsmanship is almost dead.
@robertkiser8465
Жыл бұрын
Best Union brick layers are out of local 4 Indiana Kentucky, This guy is a boot..
@robertkiser8465
Жыл бұрын
Only boots double butter.🤣🤣
@kensterling5217
Жыл бұрын
@@robertkiser8465 Only Boots and Apprentices don't. I have Built Buildings that are on TV Every day including Multi Billion dollar Vegas Casinos. You would be Schooled Quick when it comes to Block, Brick, Stone, Concrete, Safe Rooms, or any Custom or Commercial work....🤣🤣🍺🍺
@robertkiser8465
Жыл бұрын
@@kensterling5217 Me Too! I belong to local 4 Indiana Kentucky, We throw full head joints 1st time we don't have to double butter, Slows down production.. I retired in 2017.. I worked on football stadium's baseball stadium's, glass furnaces, I've done it all bruh. Traveled all over the United States, Have trowel will travel that was our motto.
@kensterling5217
Жыл бұрын
@@robertkiser8465 I always double butter and will still be the fastest. Most Halls used to teach that, I doubt it now. I walked in one years ago and nobody spoke English. But they also had trouble with different ones running off with the Union money. I have worked Coast to Coast and the Best Hall that I have seen is Portland local 1. The City is a mess. As for Building Codes....Vegas and LA are the Best, because the Codes are based on Earthquakes. Florida and Most places need to Really step it up. Michigan has the Worst Building Codes that I have seen and I thought some of the Hillbilly stuff was bad...but Michigan is definitely the Worst that I have seen. Actually I am a Master Mason, I have 45 years of experience from Coast to Coast. And the Master Masons that I have met, I could count on 1 hand. But I am still amazed at some people's tooling.....What...?? You don't have a Hubbard, you have got to be kidding me....In Georgia they do some of this Grapevine jointing, it's different. I do like talking with Masons that know their chit. What I see a lot of is Contractors taking Shortcuts, that really Aggravates me. Like Safe Rooms in Tornado Alley, most are easily under Built. These Contractors are Building these Safe Rooms and this Family is going to it for Protection but they are Under Built,...Very Sad, I am surprised people like that can sleep at night. And I look around and see Craftsmanship Dieing, it's Sad 😔
@user-yu9bt2qn9j8 ай бұрын
As a bricklayers foreman, if I ever saw that somebody measured the first course with the tape measure, I would personally take the tape measure and toss it
@mateuszsynku3900 Жыл бұрын
🤣🤣
@metalrooves3651 Жыл бұрын
That wire is a waste..of money and just more thing to do!Helps almost none
@ralphfrench29249 ай бұрын
😂
@MudHere12 ай бұрын
For all the people watching this. If you build a wall this slow on the jobsite you will be fired.
@bulldog76609 ай бұрын
Remove the pathogen thorium and we good. Jk😂
@user-se8ds5ev5k2 ай бұрын
Why ain't there no vertical rebar in the corner? How come you ain't checking your height after each and every Single course? This is exactly why you're a rookie, and you will be called a boot in my state of Texas! Hell, you never even checked your overall height!😂😂😂😂😂😂
@robertkiser8465 Жыл бұрын
I've worked with a lot of 🤡 🤡 like this guy over the years.🤣🤣
@mikepignato8859 Жыл бұрын
Cheap jointer
@phutimalapile1924 Жыл бұрын
Where is DPC? "Dam prove Corse"
@kprice3996 ай бұрын
This guy is an inspector not a mason. He should watch mason 201 for proper technique. I watched up to the fourth block, made my comment and then left. I don’t want to learn from this guy. I
@ahole5407 Жыл бұрын
Just like a union worker. Taking 10X longer to so a simple task. I wonder if he had 3 guys off camera holding the ground down so it didn't move on him 😂
@user-assoul_
11 ай бұрын
Hater😂
@richardwhiting1480 Жыл бұрын
I wonder why he left the "TAB WIRE" hanging out beyond the exterior of the wall. You can see clear to the end , he did not mention why. Also, how is it cut off ? (If necessary)
@Joshua-cx4hd
Жыл бұрын
they are left long to pick up the next piece of wire when he runs the block between the leads
Пікірлер: 129
Thank you for giving us this free valuable lesson many are sitting on school writing an essay of paying thousands of dollars. Taking it up to the 7th course we go the main point especially if you are a GC like myself
you are surely a great teacher and very neat in your work.
This was great I hadn’t laid block in a while but it was a good refresher
Nice to see you are using a Stabila Level from Germany 🇩🇪😊 Does she like your freedom units? She is only familiar to meters and centimeters. At least rectangular angles are also 90 deg in the US. 😅
Great presentation and followup before closing. You are a great teacher. Thank you for sharing.
Those look like some very well made block. I have seen some that your level would wobble on top of. Very hard to build a decent wall with trash like that but we did it every day. Good job. Good trowel, W. Rose always made the best. I also prefer the leather wrapped handle.
brings back memories...I started my apprenticeship back in n1978
@user-cl9dy6fc6o
2 ай бұрын
I started in 1972
Overall good information but I would like to see a better head joint. Many masons will have a full head joint then ruin it by sliding it down. This removes most of it. A better way is to push into block because it compacts the mortar fully without dropping down. Just something I have learned over the years and wish I was taught that in the beginning.
@tonylinardi3089
2 жыл бұрын
Shove joints are the best joints!
@afrokidd214
2 жыл бұрын
Yes i wish some would tought me that but recently i was laying block with a old school so he schooled me on that cause i would leave gaps and double work went i had to joint and refill them
@ficknoti
Жыл бұрын
Not these days lol
@bradmason8334
10 ай бұрын
How would you construct this type of wall for superior strength for hind wind areas?
@brikkijim
10 ай бұрын
@@bradmason8334 Rebar every 24 inches filled core. From footing to the top. Bond beam every 4 feet in height with a bond beam at the bottom and at the top. Durawall in the bed joints every 16 inches. If possible plaster/stucco one side of block to reinforce the entire wall. This is for extreme conditions and obviously have temporary supports until all is cured.
Thank you for your tutorial. Very helpful!
@constructionnew
10 ай бұрын
❤❤❤
Thanks for sharing your wealth of knowledge
Wow that was so perfectly informative 👌 and neat
Gracias por buen curso yo también soy blockero saludos desde Tijuana 💪👍🐓
Great job!!
What a good lesson.
Watching from west Africa
Gracias .Difrute y aprendi mucho con su video
Very neat finish. Thankyou for your ideas.
@formukongdieudonne5922
Жыл бұрын
I will be wanted to work with your company
@formukongdieudonne5922
Жыл бұрын
😂
Nice work sir am impressed
Is the tab wire needed if you are doing a straight wall without having access to the corner of the other walls. I assume this is for strenght.
Corner blocks should always be checked vertically instead of horizontal with the level, best way to keep it going up straight.
Thank you sir I learn your vidio❤❤❤
Awesome
Is that wire between the courses for brick wall ties also?
@user-cl9dy6fc6o
2 ай бұрын
It can be made in such a way that a brick wall can be tied to the block wall. That type wire has loops on short wire that sticks out the side of the block. Another type wire is inserted in the loop and laid into the brick as you build that wall. Alternatively, you can lay both walls at the same time and put wider wire in every 2 courses or so. In that scenario you would use 12 inch wire for an 8 inch block wall with a brick veneer.
How would you construct this type of wall for superior strength for high wind areas? Rebar & cement inside of block or something else?
@user-cl9dy6fc6o
2 ай бұрын
It is common, especially in commercial construction, to run a vertical cell full of grout with rebar at prescribed intervals. In prisons they often pour every cell.
Thanks so much
Thanks! Do you have to fill in the head gaps, for each level ? before the next level goes up. There is a hollow there I see, so wondering does that need filling also ? And secondly, would it be a good idea to fill the cavities of each block with mortar, or just a waste ? (have seen the vertical rebar cavities filled, but asking if its good practice regardless of rebar or not for overall strength ? Thanks again
Good job
❤❤❤❤
A good idea would be to is nail a straight edge on the ground to your square line so to be sure that your block is layed on the line
@Steven-mm7gb
5 ай бұрын
can spray that chalk line with clear coat, will keep it bright and wont go away no matter
Very good 👍
@phoenixdepannage9103
Жыл бұрын
Hjtx
Thank you
Nice ❤️
Perfect
Top !
Interesting thank you but, what on earth is tab wire. Google doesn't seem to recognise it nor can I find any trace of it here in Europe. What are the 2 tabs for?
@genepires9394
6 ай бұрын
its dura wall, galvanized reinforcement. The 'eye's' receive a tie for a veneer brick wall
Ever hear anyone setting the wire into the mud rather than spreading on top of the mud?
Top
Great video! I'm an instructor in Canada, are you looking for instructors?
@baclocal1mvd40
2 жыл бұрын
Thank you! If your are interested and open to relocation, please inquire on our website.
🎉🎉🎉
Your worth about 20 bucks an hr here in Calgary! I would have to yell at you all day with your work!
Fill head joints ?? Make sure they are packed ?? Clipping the block is not full
can you plumb from inside the wall instead of outside ??
@jimmyboy2844
2 жыл бұрын
Only plumb one side and yes you can plumb from the inside. Just pick one and stay with it!
@richardstetson8221
2 жыл бұрын
You still have to plumb the outside corner from the outside of the wall unless they are split-face block
@robertkiser8465
Жыл бұрын
Not building a corner wall..
what are these wires outside of the wall for?
@jareddaugherty84
Жыл бұрын
To tie it together with a brick veneer
Not sure what your blocks are made of but here in the UK our hollows are 26kg (over 50lbs) not sure I could lift with one hand, maybe your superman
@chadcornick4655
Жыл бұрын
Well this guy's abilities of spreading mortar is good for a laugh are blocks here in the US are typically around 35 to 50 pounds each more the 50 pounds any more it's stupid 3" split face side walls with some center web 3" and corner blocks can and do get around 4" the engineers that spec the blocks don't seem to grasp that steel with over lap goes in these blocks along with electrical and plumbing and the concrete and steel are what give it its true strength and limiting them is not all that smart. 55 to 65 pounds a block one handed is no problem even with high rebar all day long small cut up jobs I will average around 200 big jobs with long walls are easy and I enjoy laying 400 to 500 a day plus that includes stocking and rebar placement and grouting and I double joint all my own work and build most all the leeds for the guys
@orgesornespllana9656
Жыл бұрын
Q😮🎉🎉🎉🎉🎉
😊😊😊😊
🤙🤙❤❤
I am interested, how can I enroll
Hi. How long is course? Also is there any training like this in Los Angeles
@terrytodd5344
2 жыл бұрын
BAC Local 4
@robertkiser8465
Жыл бұрын
3 to 4 year apprenticeship, Then you can get your journeyman's card..
@hakimislam6218
Жыл бұрын
I started out in Los Angeles, BAC Local 4 now I'm BAC Local 4 in NJ
Pls how can I join you to training me boss back in Nigeria I'm a bricklayer now I'm in London now working at site as a cleaner Reply me pls
Please order a quality camera, this one is very pixelated.
I, hope he's building fish tank and not house because no hold drill for rebar as they call stell maybe this why some home cap size in earth quake they laid neath and he worked clean.
What's the size of a block plz
I nice love
Aya papa📖📖📖📖📖📖📖📖📖📖📖📖📖📖
@aychewzegeye6385
Жыл бұрын
ቆንጆ
Why do Americans lay blocks upside down?
ALRIGHT ROUGH UN
I think he would use 2 blocks to make a square, before a straight laying 🤫
Jointing the outside is unnecessary if you're using hook and eye wire.. other than that, good video.
Раствора маловато под блоком. Или вы потом бетоном заливаете. Для усиления стены?
@waltherheinrich
Жыл бұрын
Это школа
@waltherheinrich
Жыл бұрын
Это школа
Never pass 3 else you will not get a straight wall. Your lever might be 4ft, but if you pass 2 and a half block out you won't get a straight wall.
Sloppy! But its not coming down. I rate you as a good second year apprentice. Work on that jointing and plumb your first course from the face of the block.
@thomasfyffe5192
2 жыл бұрын
Ok master block layer how is it sloppy?
@jimmyboy2844
2 жыл бұрын
@@thomasfyffe5192 Let me count the ways. First off, Its always a mistake to lay past a level. A level is only accurate to 3 mm. It says it on the level. So 4 blocks long max, Also, Plumb the face of the first course. Joint/pointing is attrocious. Dont just lay one block and then use the level. Soften your mud. The list goes on. Second year where I come from. Wire has been installed sloppy. Insufficient overlap left out and why would you use 2 seperate pieces? Thats just the lead, What other sloppy mistakes do you make on the wall to make up time? Because you didnt plumb the face of the first course, You more that the 3mm out on a level and wondering your whole life why. Every course is tipped the opposite way to correct it on the level. Mistake after mistake results in deficiencies.
@jimmyboy2844
2 жыл бұрын
@@thomasfyffe5192 Yes, I am a master Bricklayer!
@nl-ds2ov
2 жыл бұрын
Nobody's perfect.....
@mppetrikas4919
Жыл бұрын
@@nl-ds2ov Jimmy boy is
Damn, another Union Apprentice with a KZread video. #1 You Always Double Butter, did you forget that ?? And you level from side to side first then long ways. Get a better level. With all these Union Halls just letting Anyone in, because of Dues. No Wonder Real Craftsmanship is almost dead.
@robertkiser8465
Жыл бұрын
Best Union brick layers are out of local 4 Indiana Kentucky, This guy is a boot..
@robertkiser8465
Жыл бұрын
Only boots double butter.🤣🤣
@kensterling5217
Жыл бұрын
@@robertkiser8465 Only Boots and Apprentices don't. I have Built Buildings that are on TV Every day including Multi Billion dollar Vegas Casinos. You would be Schooled Quick when it comes to Block, Brick, Stone, Concrete, Safe Rooms, or any Custom or Commercial work....🤣🤣🍺🍺
@robertkiser8465
Жыл бұрын
@@kensterling5217 Me Too! I belong to local 4 Indiana Kentucky, We throw full head joints 1st time we don't have to double butter, Slows down production.. I retired in 2017.. I worked on football stadium's baseball stadium's, glass furnaces, I've done it all bruh. Traveled all over the United States, Have trowel will travel that was our motto.
@kensterling5217
Жыл бұрын
@@robertkiser8465 I always double butter and will still be the fastest. Most Halls used to teach that, I doubt it now. I walked in one years ago and nobody spoke English. But they also had trouble with different ones running off with the Union money. I have worked Coast to Coast and the Best Hall that I have seen is Portland local 1. The City is a mess. As for Building Codes....Vegas and LA are the Best, because the Codes are based on Earthquakes. Florida and Most places need to Really step it up. Michigan has the Worst Building Codes that I have seen and I thought some of the Hillbilly stuff was bad...but Michigan is definitely the Worst that I have seen. Actually I am a Master Mason, I have 45 years of experience from Coast to Coast. And the Master Masons that I have met, I could count on 1 hand. But I am still amazed at some people's tooling.....What...?? You don't have a Hubbard, you have got to be kidding me....In Georgia they do some of this Grapevine jointing, it's different. I do like talking with Masons that know their chit. What I see a lot of is Contractors taking Shortcuts, that really Aggravates me. Like Safe Rooms in Tornado Alley, most are easily under Built. These Contractors are Building these Safe Rooms and this Family is going to it for Protection but they are Under Built,...Very Sad, I am surprised people like that can sleep at night. And I look around and see Craftsmanship Dieing, it's Sad 😔
As a bricklayers foreman, if I ever saw that somebody measured the first course with the tape measure, I would personally take the tape measure and toss it
🤣🤣
That wire is a waste..of money and just more thing to do!Helps almost none
😂
For all the people watching this. If you build a wall this slow on the jobsite you will be fired.
Remove the pathogen thorium and we good. Jk😂
Why ain't there no vertical rebar in the corner? How come you ain't checking your height after each and every Single course? This is exactly why you're a rookie, and you will be called a boot in my state of Texas! Hell, you never even checked your overall height!😂😂😂😂😂😂
I've worked with a lot of 🤡 🤡 like this guy over the years.🤣🤣
Cheap jointer
Where is DPC? "Dam prove Corse"
This guy is an inspector not a mason. He should watch mason 201 for proper technique. I watched up to the fourth block, made my comment and then left. I don’t want to learn from this guy. I
Just like a union worker. Taking 10X longer to so a simple task. I wonder if he had 3 guys off camera holding the ground down so it didn't move on him 😂
@user-assoul_
11 ай бұрын
Hater😂
I wonder why he left the "TAB WIRE" hanging out beyond the exterior of the wall. You can see clear to the end , he did not mention why. Also, how is it cut off ? (If necessary)
@Joshua-cx4hd
Жыл бұрын
they are left long to pick up the next piece of wire when he runs the block between the leads
❤❤❤❤