Man, you brought the old girl back from the dead

@carthageclassiccars

9 ай бұрын

Thanks, it is such a great feeling thinking where most started and getting to this point. Thanks for watching!

As a mopar guy.. I can say these gaps are way to good. lol Nice workmanship.

@carthageclassiccars

11 ай бұрын

Thank you very much!

@prawnstar9213

2 ай бұрын

I was thinkin the same thing.. I see too many “restored” cars tho with all sorts of screwed up looking panel gaps where the trunk or hood meet. Or a hood that’s slightly raised on one side and doesn’t lie flat. That’s just lazy.. however it seems that’s the least of a buyers worry these days. The stuff my families body shop has seen from people buying classic cars from auction are very expensive nightmares. They look so great when you first get a gander.. you get under it and we’ve seen sections of frame rail made out of bondo.. bondo door panels that are shaped even yet have zero metal anywhere. The worst was when someone used a dent puller tack AS A WELD. Yep..

Expert level. Not only the craftsmanship, but the ability to teach it and translate via video. Not an easy task. Thank you so much for sharing your knowledge.

@carthageclassiccars

11 ай бұрын

You are welcome thank you for watching and the kind words.

Glad I found your channel. You not only have a talent for restoration. You are an excellent teacher. Thanks.

@carthageclassiccars

9 ай бұрын

Thank you very much I appreciate you following along.

Great job. Learned a lot! This will come in handy when I set the gaps on my 74 Challenger.

@carthageclassiccars

5 ай бұрын

Thanks a lot, check back in about a week I am working a hopefully a better updated video right now on gapping e body cars.

Great video and perfect timing. I’m setting gaps on my 65 Plymouth satellite, your tips and tricks are very helpful thanks

@carthageclassiccars

Жыл бұрын

Thank you and good luck on your project really glad it was helpful

Really lookin good. Undoubtedly a whole lot better than what Ma Mopar allowed to go out the door back in the day.

@carthageclassiccars

Жыл бұрын

Thank you and yes I agree

I've been sat binge watching this build series, great content. 😎

@carthageclassiccars

Жыл бұрын

I appreciate you following along thank you!

You’re great at what you do.I’m doing a1970 cuda with all your tips I’m very impressed!

@carthageclassiccars

6 ай бұрын

Thats great to hear the videos might help out good luck on your 70 build. I also am in the process of doing a 70 Cuda currently.

Sir, your videos, or should I say tutorials are a top notch, no nonsense guide to bodywork they are an invaluable resource.... your tips and tricks / techniques are some of the best I've seen on KZread or anywhere else for that fact... just watching your instruction has helped me on my own projects immensely. While I have a good foundation for metal work and fabrication.... I personally think that your instruction is next level especially for those of us who want to do the very best work we can possibly do.... I just want to thank you for your time and expertise in putting together these videos.... I can't iterate it enough how much you've helped me.... Thanks again.... BTW I subscribed to your channel after watching just one of your videos.... Great job !!!

@carthageclassiccars

10 ай бұрын

Thank you very much for the kind words and subscribing it really means a lot again thank you!

Master craftsman. Your attention to detail is to be applauded.

@carthageclassiccars

Жыл бұрын

Thank you very much I really appreciate that!

Awesomeness! A Craftsman at work.

@carthageclassiccars

Жыл бұрын

Thanks a lot

Great video. I have seen things on this video that I have not seen on others. I learned some new tricks from this. Thanks :)

@carthageclassiccars

11 ай бұрын

You're welcome thanks for the feedback!

Rick you’re doing an awesome job on the challenge at 69 challenger I like the way you work

@carthageclassiccars

Жыл бұрын

thanks

Great tips and technique from a real Craftsman

@carthageclassiccars

Жыл бұрын

Thank you very much I am glad you enjoyed it

Buying less than quality panels because there is no other choice these days equates to a lot more work . This work is perfect.. it’s down to the mm on those doors!

@carthageclassiccars

2 ай бұрын

You are 100% right and thank you very much for the kid words and watching!

Attention to detail is amazing, some great tips here

@carthageclassiccars

Жыл бұрын

Thank you

Masterful work.

@carthageclassiccars

Жыл бұрын

Thank you

Excellent video. Learned a lot!

@carthageclassiccars

Жыл бұрын

Thank you and glad to hear!

Your job is amazing, thanks for sharing 💪

@carthageclassiccars

Жыл бұрын

Thanks a lot appreciate you checking it out.

Awsome work man 👍🏻🍺🍺

@carthageclassiccars

Жыл бұрын

Thank you very much

Perfect attention to detail many thanks for the info

@carthageclassiccars

Жыл бұрын

You are welcome and thank you!

Best video I've seen on this..good job

@carthageclassiccars

Жыл бұрын

Thank you

At some point I imagined doing something similar on my 1972 Fiat 500 to improve the gap between panels a little, but I considered that it would be very radical or daring to do it, now that I see you working so confidently you inspire me to finally try it. This video is enough to subscribe to your channel. Greetings from Ensenada, Baja, Mexico

@carthageclassiccars

7 ай бұрын

Greetings, thank you for subscribing and watching glad it helped.

Great video amazing work

@carthageclassiccars

Жыл бұрын

Thank you very much!

I am amazed as usual :o) it is going to be a stunner.

@carthageclassiccars

Жыл бұрын

Thank you

Really well done! You really aim to do everything you can to minimize body filler. I have a 70 Cuda and the front of the trunk is so high above the dutchman paner, or panel behind rear glass. Funny thing is that the sides and rear seam to fit nicely. Anyway, you really inspire me to get to work on it! Thank you

@carthageclassiccars

9 ай бұрын

Thanks a lot and yes less filler is the goal. Good luck on your Cuda a little cutting and welding and it will save you lots of headaches down the road.

Great Video. .. Working on Chevelle panel gaps

@carthageclassiccars

Жыл бұрын

Thank you and good luck with your Chevelle

Excellent.

@carthageclassiccars

Жыл бұрын

Thank you!

Nice work !

@carthageclassiccars

Жыл бұрын

Thank you

Like I said b4 you are great at what you do

@carthageclassiccars

Жыл бұрын

I really appreciate it!

You are an amazing craftsman!! I've watched hours upon hours of your work. Where are you located?

@carthageclassiccars

6 ай бұрын

Thank you for watching and Carthage North Carolina

where did you learn all this at. you have impressed me big time and have learned a lot. thanks. Is this your living or just a hobby?

@carthageclassiccars

Жыл бұрын

Thank you very much! I have been messing and around hot rods my whole life so mostly trial and error. I have spent many years racing and building race cars so most of my fabrication has been learned doing that consistently. I started restoring more of flip cars in my early 20's as a hobby along with my own stuff, then worked on friends/family cars and the hobby over the years has turned into the business it is now. I am always trying to build on my skillset and be better with each project so self motivation has some to do with how I work. Thanks for checking out my videos also.

Rick, another great tutorial, thanks! So, I have a question and forgive me if I'm missed it among your other videos. Much time is spent gapping and profiling the panels and then you pull them sometimes to paint. I'm talking, doors, trunk, fenders, etc. After paint, how do you quickly and accurately align those panels without chipping paint? Do you have some kind of process for that? If you've not done a video on this, I'd sure like to see one from you. Thanks!

@carthageclassiccars

10 ай бұрын

So sometimes I will drill a 1/8 hole and align the panels back up and that hole would be covered by a bolt or sometimes I just realign. It honestly depends how hard the panels are to get where they go. I also make sure any shims are labeled as I am removing them so its easier to align. Saying that I am working on the second part of the body work video on this car. Its been on the friends and family plan so taking a while but I will try and cover my process in that video how I go about finishing it to try and show you how I paint them to avoid damage as much as possible.

@johnlindsay6039

10 ай бұрын

Thanks, Rick!

👍🏼

@carthageclassiccars

Жыл бұрын

thanks

Looks really good. Do you use this same process on other vehicles that require perfect gaps?

@carthageclassiccars

Жыл бұрын

Thank you and yes for the most part I use some version of this process depending what the owner is looking for. Some are more then happy with how the car started it as especially with a driver. I am always trying to think of new ways to make the process better. I have also used lead before to add to gaps to close them up also on jambs.

Thank you for the awesome videos. As everyone else has said, this is excellent work and your passion is inspiring. I have been in the process of restoring 70 Cuda myself and in need of panel gap help. Is it possible i could email you some pictures? Thanks again!! Alex Franklin

@carthageclassiccars

Жыл бұрын

You welcome and send me an email to carthageclassiccars@gmail.com Ill see if I can help you out.

I love the work you put into the car. But there is still something wrong with it.... With the clearances worked into it, you keep it well outside factory standards. All parts within the same time-zone..! Something's wrong here....😂🤣

@carthageclassiccars

9 ай бұрын

Haha Yes you are correct I will take that as a huge compliment, thanks a lot for watching and the feedback.

Great video. Did you buy the spacers or make them

@carthageclassiccars

9 ай бұрын

Thank you and I bought them off amazon just universal body shims

Nice work! When slicing the panels how to you treat the backside of them?

@carthageclassiccars

Жыл бұрын

That is a great question, unfortunately if the spray and pray doesn't get it that will be an area without primer on it. I know its not the ideal case, however if you see most of these cars had large portions of bare metal from the factory a small spot here and there is still better then they were. If you also think about it anyplace you weld even with the weld through primer will burn it off a bit. We can't make it 100% covered but we do the best we can so they live on for the next 50 years even better! Good thing about that is all the time if paint can't get to it water should not also be able to touch it slowing down any corrosion.

use a 2x4 under door to pound on , rocker

@carthageclassiccars

Жыл бұрын

That's a great trick thanks I will do that next time

Do you seal the weld underneath with anything? Thanks...

@carthageclassiccars

4 ай бұрын

The goal is to try and spray epoxy on the back sides where they are accessible, in reality that might not always be the case, but we do the best we can.

Can you tell me if the 70 nova you did had 1 trunk lid torque bar or 2. Thank you.

@carthageclassiccars

Ай бұрын

If I remember right that 70 Nova had two where this Barracuda in 71 had 1. I have a 68 Nova in the shop now with 2.

Sweet .... curious if this a match build or clone ish?? I have 71 383 Mag. H.P. Match's Barracuda Gran Coupe most optioned E-Body made 1 of 32 believe. Possible 1of 19 told!!!

@carthageclassiccars

7 ай бұрын

This one will be a tribute in the loose sense of the word. It was a base model Barracuda. Your 71 sounds like a really awesome optioned car, take care of it.

@henryknedel5683

7 ай бұрын

Yeah I noticed figured it was! All 👍. Do ya already have drivetrain fit the plan?

@carthageclassiccars

7 ай бұрын

Yes I have all the drivetrain parts ready for the most part for assembly already

the attention to detail is awsome great workmanship. Would you possibly consider filling the gap between roof and quarter panels with weld rather than lead ?

@carthageclassiccars

Жыл бұрын

thank you and personally I would not weld up that entire gap. Lead melts in a lot lower with the heat then you would ever have to get to weld mild steel. So the heat it would take I feel to add that kind mild steel tig rod in a gap that large would have a great chance of warping the panels. If you had your heart set on that i would put a patch over the two edges covering the middle gap and weld that up, but to me that also doesn't have any advantage. Also the amount of time on the welding machine would be a lot, just in general I don't think practical. Lead has proven to last decades upon decades so I think that is a good option also I would also consider using kitty hair or a alunimunized filler material like All Metal.

@brianwadhams1518

Жыл бұрын

@@carthageclassiccars Thanks your thoughts, I agree lead has been used for years successfully, I wondered if it was used by manufacturers as was much simpler and quicker to apply in factory conditions than 'cut and butt'. Great work by you, will look forward to future videos.

@carthageclassiccars

Жыл бұрын

I think your right, the cheapest and easiest way to fill any slight fitment differences between how each car fit up between the roof and quarters.

@brianwadhams1518

Жыл бұрын

@@carthageclassiccars 👍

What do you do if you open the trunk and rain water gets inside

@carthageclassiccars

Жыл бұрын

it sounds like the seal is cracked or damaged or there is a rust hole in the drip rails. Look closely and find the hole and seal it up. There are many ways to do that job depending on what you find. Good luck.

@BeefandEggs

Жыл бұрын

Thank you

First :)

Put the phone and the address

@carthageclassiccars

Жыл бұрын

Carthage North Carolina 910-722-9552

Dear Lord , my car is going to look like crap compared to your work.

@carthageclassiccars

Жыл бұрын

Thanks a lot. I would say this is not the standard, but hang in there if you want it this way all it takes is time and effort. If not just build and enjoy it how you want too.

Why not use brazing to add material for your gaps? It's easy to add and shape.

@carthageclassiccars

Жыл бұрын

I do TIG braze on these cars every now and then. I actually have done in on some of my videos to show where i use it. Mostly in seam areas or filling gaps. Personally I like traditional weld fusing the panels together if I cut the door, put a slice in a panel to relief it back and even building up an edge a fused weld is far superior in strength. Thats why you really should be butting panels and brazing them to hold then together. That is not saying brazing wouldn't work as you described more of a personal preference. The only benefit I see to brazing is less heat input and easier to sand down. The downsides I see is where i weld on the edges I don't have to worry about the heat and the cost factor of brazing rod is just so high compared to its mild steel counterpart. To me there is no enough benefit to justify it.

@chiefwraps7711

Жыл бұрын

@@carthageclassiccars thank you for your knowledge.

@carthageclassiccars

Жыл бұрын

you are welcome thanks for watching!