While your there grab u a quick ratio steering box out of a 96-98 keep grand Cherokee 12.7:1 box . 💪🏻 the 94 and down jeep Cherokee has a upgraded steering shaft for the Gbodys to .
@87SSBOI
5 ай бұрын
Got the shaft and box already…thanks 💯
@PENNYLS110 ай бұрын
It’s good you took the Hub bolts. The new hubs don’t come with bolts. Mine didn’t anyway.
@87SSBOI
10 ай бұрын
Whewww, glad I did cause I didn't know...hubs, rotors and pads supposed to be here tomorrow😃
@tredog8610 ай бұрын
I knew where you was at when I heard them jets flying. Good Find 💯💪🏾
@87SSBOI
10 ай бұрын
😂😂😂…man them thangs annoying af
@willierebuildz918210 ай бұрын
Nice work the back not hard just have to pull the axles👍🏿
@87SSBOI
10 ай бұрын
Word!!! I’m on it!! All brake parts on sale this week at my yard for $15…I’m going back tomorrow
@Weekend_Warrior_DMW10 ай бұрын
That yard boujie.😂 They have stands under all the cars. Yards up here cars be on the ground or random car rims under them.
@87SSBOI
10 ай бұрын
😂😂😂 that’s why I like that one the best
@t.l.robinson216210 ай бұрын
Clamp a pair of vice grips to the cotter pin then use a hammer or a pry bar against the vice grips.
@87SSBOI
10 ай бұрын
Them thangs gave me 🤬🤬🤬
@javarislofton17263 ай бұрын
U can use the front and rear of a blazer and I think you can use the rear from a Camaro 98-02 I believe
@87SSBOI
3 ай бұрын
Facts! Yes I have the rear blazer as well just haven’t installed yet
@t.l.robinson216210 ай бұрын
The calipers will clean up, easily.
@marcosponce44224 ай бұрын
Man trying to find 2wd spindles where im at in michigan feels like ill lever find any. Even went to the pull and save nothing but 4x4s. But i did find set of 4 camaro calipers and brackets. Even get a posi and backing plates for rear end.
@87SSBOI
4 ай бұрын
Nice
@CatlocosGarage10 ай бұрын
Good job bro. Been on that run a few times. :)
@87SSBOI
10 ай бұрын
🫡
@mr.g.d.i.y10 ай бұрын
Good vid brah! My first video was me getting the blazer setup I still got it 😂 I’ll eventually switch to them I think it will barely clear my rally’s that’s why I didn’t go right off the bat. you got 24s so you good lol. Looking forward to the next video! 💪🏾
@87SSBOI
10 ай бұрын
Yessir!! Ay bro I’m pretty sure they fit with the factories cause the rotors are the same size and if I’m not mistaken, the blazers came with 15s
@mr.g.d.i.y
10 ай бұрын
@@87SSBOI yeah. but hell I want brembo too 😂 or camaro brakes either way i need to stop lol
@87SSBOI
10 ай бұрын
@@mr.g.d.i.y 😂😂😂…yea u go Brembo u gonna need 17 or 18 at least
@mr.g.d.i.y
10 ай бұрын
@@87SSBOI yeah that’s why I gotta wait until I get some 24s lol.
@jemelmonger10 ай бұрын
6.0s out there Fa shoooo.
@87SSBOI
10 ай бұрын
Yessir
@PENNYLS110 ай бұрын
Notification squad 💪🏾
@87SSBOI
10 ай бұрын
Yessir 👌🏾✊🏾✊🏾
@87SSBOI
10 ай бұрын
Appreciate that feedback earlier too
@MaXpeedingRods_Coop10 ай бұрын
keep your work
@87SSBOI
10 ай бұрын
🫡
@baims83675 ай бұрын
U want a 5.7 vortec headed sbc. There on 96-99 trucks and Escalades.
@criskyro5 ай бұрын
Thanks for thre info! heard the G Bodys are the same as 1st gen s10s How much did the spindles and calipers end up costing you boss?
@87SSBOI
5 ай бұрын
What’s up! I paid $60
@keegottifoster233110 ай бұрын
And also i had got my hubs new off ebay too
@87SSBOI
10 ай бұрын
Yea same I did, went with Detroit Axle…didn’t wanna trust the yard hubs
@flipmode92367 ай бұрын
what size socket where those castle nuts. gotta make sure i got the right size
@87SSBOI
7 ай бұрын
I’m sorry, I can’t remember for sure but I think 18 or 19mm
@DMDAUTOLLC10 ай бұрын
What did that all cost?
@87SSBOI
10 ай бұрын
$60
@DMDAUTOLLC
10 ай бұрын
@@87SSBOI ohhh bet to the junkyard I go
@87SSBOI
10 ай бұрын
@@DMDAUTOLLC 😂😂😂…gotta go back and get the rear…$60 for that too
@SHyYL0n2 ай бұрын
What does this do?
@87SSBOI
2 ай бұрын
Better braking and upgrade to wheel hub
@shuntubbs268210 ай бұрын
No cutlass parts or parts for the other vehicle?
@87SSBOI
10 ай бұрын
Oh nahhhh NEVER cutlass parts…
@Mr.Frost18110 ай бұрын
I'm getting mine off the same blazer
@87SSBOI
10 ай бұрын
🫡
@t.l.robinson216210 ай бұрын
When are you going to put your gas saver on the road?
@87SSBOI
10 ай бұрын
Pretty soon but look like it ain't gonna be mine any more...my son getting his license soon...guess I gotta find me another one
@baims83675 ай бұрын
F slotted rotors there really just for looks I’m not a fan of them because they create many edges for the pads to rub on and imo causing excess brake noise. I’m not a fan of any unnecessary brake squeaks / noise, and I find that the slots on the rotors do just that so stay away from slotted rotors just go with drilled if you can find them or honestly just a regular solid rotor is all u need the drilled and slotted are manly just looks if your worried about cooling run you a brake duct from allstar performance or summit etc
@87SSBOI
5 ай бұрын
Word 👌🏾
@baims83675 ай бұрын
Where’s your caliper hardware man ? Should have kept all the caliper hardware right in them u gonna need the bracket bolts and the pins .
@87SSBOI
5 ай бұрын
All that was in my bag…lol…Preciate ya
@1godgodgodgodgod7 ай бұрын
Umm. No one ever mentions that you will get an inch lift and wider front stance with these
@87SSBOI
7 ай бұрын
Weird, because I didn’t…but I also didn’t install the spindle and brakes until I installed my upper and lower tubular control arms and QA1 coilovers so that’s probably why I didn’t notice but this is the first time I’ve heard it 🫡
@87SSBOI
7 ай бұрын
And front is lowered like 2.5 inches now on the coilovers on 24s
@1godgodgodgodgod
7 ай бұрын
@@87SSBOI dumb me. I forgot a had gbody drop spindles on. so that explains the ride height. but the stance is wider about an inch. I had to run spacers to clear end links now i dont.
@87SSBOI
7 ай бұрын
@@1godgodgodgodgod word!!!
@GSM21510 ай бұрын
Go ahead and put you an LS in that Monte Carlo
@87SSBOI
10 ай бұрын
Maybe later
@waynegreen67896 ай бұрын
Grab me a set bro
@user-vg5bu5dj9s10 ай бұрын
Pull that 6.0 up outta there, break me up!
@87SSBOI
10 ай бұрын
😂
@user-vg5bu5dj9s
10 ай бұрын
@87SSBOI keep up the good content I injoy your channel
Пікірлер: 73
Every little project makes a big difference.
@87SSBOI
10 ай бұрын
Yessir🫡
While your there grab u a quick ratio steering box out of a 96-98 keep grand Cherokee 12.7:1 box . 💪🏻 the 94 and down jeep Cherokee has a upgraded steering shaft for the Gbodys to .
@87SSBOI
5 ай бұрын
Got the shaft and box already…thanks 💯
It’s good you took the Hub bolts. The new hubs don’t come with bolts. Mine didn’t anyway.
@87SSBOI
10 ай бұрын
Whewww, glad I did cause I didn't know...hubs, rotors and pads supposed to be here tomorrow😃
I knew where you was at when I heard them jets flying. Good Find 💯💪🏾
@87SSBOI
10 ай бұрын
😂😂😂…man them thangs annoying af
Nice work the back not hard just have to pull the axles👍🏿
@87SSBOI
10 ай бұрын
Word!!! I’m on it!! All brake parts on sale this week at my yard for $15…I’m going back tomorrow
That yard boujie.😂 They have stands under all the cars. Yards up here cars be on the ground or random car rims under them.
@87SSBOI
10 ай бұрын
😂😂😂 that’s why I like that one the best
Clamp a pair of vice grips to the cotter pin then use a hammer or a pry bar against the vice grips.
@87SSBOI
10 ай бұрын
Them thangs gave me 🤬🤬🤬
U can use the front and rear of a blazer and I think you can use the rear from a Camaro 98-02 I believe
@87SSBOI
3 ай бұрын
Facts! Yes I have the rear blazer as well just haven’t installed yet
The calipers will clean up, easily.
Man trying to find 2wd spindles where im at in michigan feels like ill lever find any. Even went to the pull and save nothing but 4x4s. But i did find set of 4 camaro calipers and brackets. Even get a posi and backing plates for rear end.
@87SSBOI
4 ай бұрын
Nice
Good job bro. Been on that run a few times. :)
@87SSBOI
10 ай бұрын
🫡
Good vid brah! My first video was me getting the blazer setup I still got it 😂 I’ll eventually switch to them I think it will barely clear my rally’s that’s why I didn’t go right off the bat. you got 24s so you good lol. Looking forward to the next video! 💪🏾
@87SSBOI
10 ай бұрын
Yessir!! Ay bro I’m pretty sure they fit with the factories cause the rotors are the same size and if I’m not mistaken, the blazers came with 15s
@mr.g.d.i.y
10 ай бұрын
@@87SSBOI yeah. but hell I want brembo too 😂 or camaro brakes either way i need to stop lol
@87SSBOI
10 ай бұрын
@@mr.g.d.i.y 😂😂😂…yea u go Brembo u gonna need 17 or 18 at least
@mr.g.d.i.y
10 ай бұрын
@@87SSBOI yeah that’s why I gotta wait until I get some 24s lol.
6.0s out there Fa shoooo.
@87SSBOI
10 ай бұрын
Yessir
Notification squad 💪🏾
@87SSBOI
10 ай бұрын
Yessir 👌🏾✊🏾✊🏾
@87SSBOI
10 ай бұрын
Appreciate that feedback earlier too
keep your work
@87SSBOI
10 ай бұрын
🫡
U want a 5.7 vortec headed sbc. There on 96-99 trucks and Escalades.
Thanks for thre info! heard the G Bodys are the same as 1st gen s10s How much did the spindles and calipers end up costing you boss?
@87SSBOI
5 ай бұрын
What’s up! I paid $60
And also i had got my hubs new off ebay too
@87SSBOI
10 ай бұрын
Yea same I did, went with Detroit Axle…didn’t wanna trust the yard hubs
what size socket where those castle nuts. gotta make sure i got the right size
@87SSBOI
7 ай бұрын
I’m sorry, I can’t remember for sure but I think 18 or 19mm
What did that all cost?
@87SSBOI
10 ай бұрын
$60
@DMDAUTOLLC
10 ай бұрын
@@87SSBOI ohhh bet to the junkyard I go
@87SSBOI
10 ай бұрын
@@DMDAUTOLLC 😂😂😂…gotta go back and get the rear…$60 for that too
What does this do?
@87SSBOI
2 ай бұрын
Better braking and upgrade to wheel hub
No cutlass parts or parts for the other vehicle?
@87SSBOI
10 ай бұрын
Oh nahhhh NEVER cutlass parts…
I'm getting mine off the same blazer
@87SSBOI
10 ай бұрын
🫡
When are you going to put your gas saver on the road?
@87SSBOI
10 ай бұрын
Pretty soon but look like it ain't gonna be mine any more...my son getting his license soon...guess I gotta find me another one
F slotted rotors there really just for looks I’m not a fan of them because they create many edges for the pads to rub on and imo causing excess brake noise. I’m not a fan of any unnecessary brake squeaks / noise, and I find that the slots on the rotors do just that so stay away from slotted rotors just go with drilled if you can find them or honestly just a regular solid rotor is all u need the drilled and slotted are manly just looks if your worried about cooling run you a brake duct from allstar performance or summit etc
@87SSBOI
5 ай бұрын
Word 👌🏾
Where’s your caliper hardware man ? Should have kept all the caliper hardware right in them u gonna need the bracket bolts and the pins .
@87SSBOI
5 ай бұрын
All that was in my bag…lol…Preciate ya
Umm. No one ever mentions that you will get an inch lift and wider front stance with these
@87SSBOI
7 ай бұрын
Weird, because I didn’t…but I also didn’t install the spindle and brakes until I installed my upper and lower tubular control arms and QA1 coilovers so that’s probably why I didn’t notice but this is the first time I’ve heard it 🫡
@87SSBOI
7 ай бұрын
And front is lowered like 2.5 inches now on the coilovers on 24s
@1godgodgodgodgod
7 ай бұрын
@@87SSBOI dumb me. I forgot a had gbody drop spindles on. so that explains the ride height. but the stance is wider about an inch. I had to run spacers to clear end links now i dont.
@87SSBOI
7 ай бұрын
@@1godgodgodgodgod word!!!
Go ahead and put you an LS in that Monte Carlo
@87SSBOI
10 ай бұрын
Maybe later
Grab me a set bro
Pull that 6.0 up outta there, break me up!
@87SSBOI
10 ай бұрын
😂
@user-vg5bu5dj9s
10 ай бұрын
@87SSBOI keep up the good content I injoy your channel
@87SSBOI
10 ай бұрын
@@user-vg5bu5dj9s I appreciate the love 💯
not an airplane,,its an AirForce F35 fighter jet.
@87SSBOI
8 ай бұрын
Does the Navy fly AF jets?
@brianmathew09
8 ай бұрын
same F35 Phantom@@87SSBOI
Good job bro. Been on that run a few times. :)
@87SSBOI
10 ай бұрын
✊🏾🫡