Detailed walkthru on how to delete OPAS on a Seadoo using a delete kit from eBay
Жүктеу.....
Пікірлер: 23
@keithbegun3763 Жыл бұрын
Thank you, good video.
@chaddenton96412 жыл бұрын
I believe you’re supposed to leave the exterior boot flange exposed so that it mates/seals into the countersink located within the large block-off plate(s).
@jonparkmac
2 жыл бұрын
No. It will give a non flushed surface for the rest of the plate and even warp it. Needs to be %100 flush or risk a leak. Should use 3M 5200 tho and not rtv like I did.
@chaddenton9641
2 жыл бұрын
Ahh.. just did one for the 1st time. You are actually supposed to transfer the seals from the cylinder supposed assemblies (Rutter), to the machines recess in the block-off plate. That is per Riva Racing instructions. Not trying to be a “know it all”.. just to help others as well! Your video helped me! Thanks!
@jonparkmac
2 жыл бұрын
@@chaddenton9641 fair enough I don't recall mine having recesses. But what you've said makes sense.
@terrydegraw5040
Жыл бұрын
all you do is screw one screw into the block off and then take the plate holding screw out
@fedorov5549
10 ай бұрын
On the exterior large plates, there is an O-ring supplied for the big hole, and you use the rubber washer from the rudder mount that you tossed out for the small hole. Silicone works probably.
@626weekendwarriors93 жыл бұрын
How did the PWC perform after the OPAS delete? Noticeable difference?
@jonparkmac
3 жыл бұрын
Little harder to steer around dock and little better handling on hard turns
@NotSoSunshineState
2 жыл бұрын
Personally I would use 5200 sealant and never look back. Nice informative video.
@mikekixaxe5515 Жыл бұрын
Great Video !! Would you happen to Have part number for this Exact kit from Riva ? It look like it may also work on a GTI ? Again , very good Video , thank you
@jonparkmac
Жыл бұрын
Glad it helped. This is what I used off eBay. I don't know about a GTI. www.ebay.com/itm/Deluxe-Billet-Fit-SeaDoo-RXP-RXT-GTX-RXP-X-RXT-X-OPAS-Block-Off-Kit-215-255-hp/313395312248?_mwBanner=1&euid=bc84a0d358434fb7882e50b53a740305&bu=45303005606&segname=11050&crd=20210607085629&osub=-1~1&ch=osgood&sojTags=bu=bu,ch=ch,segname=segname,crd=crd,url=loc,osub=osub&mkcid=7&mkpid=0&emsid=e11050.m43.l1123&ufes_redirect=true&ul_noapp=true&pageci=512f13f7-1777-4f73-92e6-727eb78ce3ce
@peterboudreaux2 жыл бұрын
where did you get the kit
@jonparkmac
2 жыл бұрын
Off eBay. The ones you want need to have drill out cavity in the back to allow for the little hold screw head. Otherwise you can drill a recess if your careful
@jasonschneck36872 жыл бұрын
Can you just plug off the hose?
@jonparkmac
2 жыл бұрын
Goal is complete remove so you don't have 4 holes in your hull to sink the ski.
@JetEnvy_TV Жыл бұрын
SHAME ON RIVA!!! I always find old parts in seadoos when I work on them 🤣
@jonparkmac
Жыл бұрын
What's the shame on Riva?
@JetEnvy_TV
Жыл бұрын
@Jonathan McClure stuffing/hiding unused or old parts in the ski is a lazy way to do things "in my opinion". The easiest part of the job is removing those line which I would pull out with the rest of the assembly instead of leaving them behind. If you pay someone to do the job, which way would you prefer?
@aaronalanis48102 жыл бұрын
do you still have the opas?
@jonparkmac
2 жыл бұрын
If you mean for sale, I was going to keep it to sell with ski to next owner
Пікірлер: 23
Thank you, good video.
I believe you’re supposed to leave the exterior boot flange exposed so that it mates/seals into the countersink located within the large block-off plate(s).
@jonparkmac
2 жыл бұрын
No. It will give a non flushed surface for the rest of the plate and even warp it. Needs to be %100 flush or risk a leak. Should use 3M 5200 tho and not rtv like I did.
@chaddenton9641
2 жыл бұрын
Ahh.. just did one for the 1st time. You are actually supposed to transfer the seals from the cylinder supposed assemblies (Rutter), to the machines recess in the block-off plate. That is per Riva Racing instructions. Not trying to be a “know it all”.. just to help others as well! Your video helped me! Thanks!
@jonparkmac
2 жыл бұрын
@@chaddenton9641 fair enough I don't recall mine having recesses. But what you've said makes sense.
@terrydegraw5040
Жыл бұрын
all you do is screw one screw into the block off and then take the plate holding screw out
@fedorov5549
10 ай бұрын
On the exterior large plates, there is an O-ring supplied for the big hole, and you use the rubber washer from the rudder mount that you tossed out for the small hole. Silicone works probably.
How did the PWC perform after the OPAS delete? Noticeable difference?
@jonparkmac
3 жыл бұрын
Little harder to steer around dock and little better handling on hard turns
@NotSoSunshineState
2 жыл бұрын
Personally I would use 5200 sealant and never look back. Nice informative video.
Great Video !! Would you happen to Have part number for this Exact kit from Riva ? It look like it may also work on a GTI ? Again , very good Video , thank you
@jonparkmac
Жыл бұрын
Glad it helped. This is what I used off eBay. I don't know about a GTI. www.ebay.com/itm/Deluxe-Billet-Fit-SeaDoo-RXP-RXT-GTX-RXP-X-RXT-X-OPAS-Block-Off-Kit-215-255-hp/313395312248?_mwBanner=1&euid=bc84a0d358434fb7882e50b53a740305&bu=45303005606&segname=11050&crd=20210607085629&osub=-1~1&ch=osgood&sojTags=bu=bu,ch=ch,segname=segname,crd=crd,url=loc,osub=osub&mkcid=7&mkpid=0&emsid=e11050.m43.l1123&ufes_redirect=true&ul_noapp=true&pageci=512f13f7-1777-4f73-92e6-727eb78ce3ce
where did you get the kit
@jonparkmac
2 жыл бұрын
Off eBay. The ones you want need to have drill out cavity in the back to allow for the little hold screw head. Otherwise you can drill a recess if your careful
Can you just plug off the hose?
@jonparkmac
2 жыл бұрын
Goal is complete remove so you don't have 4 holes in your hull to sink the ski.
SHAME ON RIVA!!! I always find old parts in seadoos when I work on them 🤣
@jonparkmac
Жыл бұрын
What's the shame on Riva?
@JetEnvy_TV
Жыл бұрын
@Jonathan McClure stuffing/hiding unused or old parts in the ski is a lazy way to do things "in my opinion". The easiest part of the job is removing those line which I would pull out with the rest of the assembly instead of leaving them behind. If you pay someone to do the job, which way would you prefer?
do you still have the opas?
@jonparkmac
2 жыл бұрын
If you mean for sale, I was going to keep it to sell with ski to next owner
@andreakristy9750
2 жыл бұрын
u can have mine