Awesome! 😁👍👍 I did my Axial Deadbolt 4 wheel steer

@UpperLeftRC

Жыл бұрын

Nice 👍

Yea v2 would be all around better as the ch3 switch is in a better spot too 👍

Everyone feels like that when trying four wheel steering for the first time, it seems like to much work and to hard to use fluidly. I recommend only use it when you really need it then you will slowly learn to steer the rear as accurately as your front. Great build man 👍🏻👍🏻

Maybe a self cantering control for the rear steer

So cool that you had all this stuff already outside to build on.

@UpperLeftRC

2 жыл бұрын

Thanks, it was lucky that my wife never used that flower bed lol 👍🏻

That opening was AWESOME😂😂😂😂

@UpperLeftRC

3 жыл бұрын

Glad you liked it 😄👍🏻

The wheel weights didn't work because the heavier ones you have are only made for stock wheel, its because the hex doesn't stick out is why it doesn't fit you'd have to grind down the part on the outside around the hex not bevel thenhex head if that makes sense

It would also be easier with a v2 then you could set the end points and set center

Nice installation thanks for sharing 😊👍

Put rear steer on baby digger to be like a real monstertruck.

@UpperLeftRC

3 жыл бұрын

That’s the plan once all the parts arrive 🤘🏼😎

Love it.. now I Am going to have to do it to my deadbolt/C10 project...😆😁 Great job on the outdoor course by the way RC sparks was also my inspiration in building mine..

@UpperLeftRC

3 жыл бұрын

Thanks bud! He inspired a lot of us I think 😎👍🏻

With the rear steering conversion you could run OD gears front and rear, finish it off with a brushless motor, that handy dandy furitek 3s main board and a 3s battery. 😂 I think that would be pretty interesting. A scx24 rock bouncer or racer if gears got done 😂

@UpperLeftRC

3 жыл бұрын

Well I got a couple furitek items on the way so I’m sure the Jeep will continue to change and grow haha I like your idea! 😄👍🏻

@jpyt7182

3 жыл бұрын

@@UpperLeftRC well thanks sir. Cant wait to see what it turns into!

Great video. I know I would mess it up turning too lol. You'll figure it out though.

@UpperLeftRC

3 жыл бұрын

Thanks bud, I’m glad I’m not the only one who kinda struggles with 4 wheel steer lol 😄👍🏻

Redcat has a radio set that is set up for rear steer and the receiver is tiny. I’m using one with my Gen8 with rear steer and one in my clodbuster. Puts the selector button under your thumb on the radio. 4 modes front steer, crab walk, four wheel, rear only.

@UpperLeftRC

3 жыл бұрын

That’s a dope set up! I might need to look into that for my Gen8 as well, hanks for the info 🤘🏼😎

@mattrogers8280

3 жыл бұрын

@@UpperLeftRC it’s a very tight fit. I got a servo on axle servo mount from shapeways made a bracket so the servo stands up on end in between the rear shock towers. And Stampede rear camber links for steering links.

Awesome mod,cool RC,subbed

@UpperLeftRC

3 жыл бұрын

I appreciate the support! 😄👍🏻

Really nice❗❗❗

😂 the jeep on the treadmill 👌

There has to be a way to splice the signal that goes to the front servo and send it to the rear one, that way it'll be proportional, like on the Rocksta. Although maybe you need to invert the signal?

@AlbertoNoys

3 жыл бұрын

Oh yeah! Got it. Splice the cable that is going to the front servo so that you can plug it into both servos. And in the rear servo, take out the screws and invert how the motor is soldered. That should do the trick :D

@UpperLeftRC

3 жыл бұрын

Excellent idea and suggestion but because I suck at 4 wheel steering I like being able to have the rear steer turned off, your idea would work awesome for a full time 4 wheel steering rig 😄👍🏻

@AlbertoNoys

3 жыл бұрын

@@UpperLeftRC yeah, I didn't want say anything but you have to get some practice man 😂

@docedits7294

2 жыл бұрын

@@AlbertoNoys Super complicated. Get a splitter and a reverse signal wire and you save yourself the hassle of souldering the worlds tiniest servo wires

@RobySVK

2 жыл бұрын

@@docedits7294 :) how would you reverse the signal wire? :) it's not as on the engine where it is "+" and "-" wires you are changing

Flysky gt5 has 4ws mix controls. Crab walk, 4w opposite steer, just rear and just front. It also has a dial to steer the rear wheels at the same time as the front. Did you figure this out eventually?

get a splitter and a reverse signal wire and itll all be on steering. No switches

What, did I miss something, what happened to Digger? Great work bro!!!🤘🤘🤘

@UpperLeftRC

3 жыл бұрын

Thanks bud and yeah Digger became a donor for parts since I have plans to mod and build it back up better than ever haha just waiting on some stuff for it 😄👍🏻

What port in the rear stear or you plug the rear servo in is it in the aux port

You are flippin hilarious

@UpperLeftRC

3 жыл бұрын

Thanks bud! 😄👍🏻

I get my furitek today. Now if I knew which brushless motor and motor mount to get

@UpperLeftRC

3 жыл бұрын

2FM RC has some great videos on furitek stuff, I should have mine by the end of April so if you don’t have any luck with info I’ll be doing a video with it as soon as I get mine 😄👍🏻

Can you help we got new ESC and is not labeled the same as old one

@lifewithlimitations9569

2 жыл бұрын

So I guess they sent the wrong ESC and are sending radio that will match the new ESC horizon has been great to work with. All parts have been free.

How did you mount the rear upper links to the stock servo tray?

@UpperLeftRC

Жыл бұрын

I don’t really remember at this point but I think I mounted them each on the outside of the center mount point with the screws meeting in the middle of the try holes

That’s cool an all.. But wouldn’t it shorten you’re runtime

@UpperLeftRC

2 жыл бұрын

I never noticed it shortening the run time, also I run 900mah batteries in it

What is rotating mass with the scx24s

@UpperLeftRC

3 жыл бұрын

Not sure I understand the question / not sure how to measure it?

Gain berham Lincoln

@UpperLeftRC

3 жыл бұрын

😂