You guys are doing great, keep it up. I am a biker in GHANA

wish you guys where over here in the uk, im having trouble setting up my cvt. but learned alot from this video and all your others. thanks guys

@wsmaga

3 жыл бұрын

Don’t you guys have a lot of scooter shops out there.

@degsy5000

3 жыл бұрын

@@wsmaga we used to , scooter tuning is not as popular as it used to be unfortunatly.

@wsmaga

3 жыл бұрын

@@degsy5000 oh didn’t know that. That sucks. I know a few places there and a couple people out there that build and tune bikes.,

@landmonkey22

3 жыл бұрын

@@degsy5000 mark savage is in the UK

@Scooterswapshop

3 жыл бұрын

Glad to help we have many cvt videos

So cool. Thanks for all the evil dead movies too mate

I've tried out a 1500 contra spring, it doesnt sacrifice much top end while increasing full throttle and half throttle acceleration. Rollers arent changed. The problem with heavier contra springs is that you need to open the gas wider from a dead start but once you get going its good. It starts at higher RPM from dead stop.

Nice video greetings from Italy ✌️

@Scooterswapshop

3 жыл бұрын

Hey, thanks!

Less talk more showing

It’s that fat weld in the rear pulley that doesn’t allow the belt to travel down all the way 🤙

For a tool. I use an old brake rotor works great to simply extend your foot position.

@Scooterswapshop

3 жыл бұрын

It does I’ve done that too!

I want to use CVT in my electric bike. I'm using Mid Drive motor currently running via chain in rear sprocket. Can we retrofit CVT ? Guidance required.

Hi I dunno if you could help or know anything about peugeot speedfights 100cc, but I can't get my cvt set up right I can't find a belt that fits properly there all rubbing on my cvt cover I have no washer in the variator and using malossi multivar variator with 9g roller, I don't know if the clutch and assembly that's on there is Original, the belt sit right at the top of the clutch but doesn't seem like it's reaching the top of my varitor where I have marked

Hey how's it going I have a 2021 Tao Tao and I was trying to take of restrictor ring but when u disassembled scooter there isn't one how do I get this scooter un restricted

The washer was in between nut and housing and its supposed to be there

I need advice, I want to get a high topspeed without sacrificing the initial acceleration, do you think crossing the heavy roller and the light roller on the CVT can help?

@Scooterswapshop

2 жыл бұрын

call tlak to Paul he can get you what you need

Hi by adding the shims to the front vari. You lost low end. And gained it back in the rear clutch ? A longer belt ? It's my first scooter .

@Scooterswapshop

Жыл бұрын

Hi we have several cvt videos I’d just watch them all to make more sense

How often do you get drops? Or do you just go out of stock real fast on the parts for the Zuma?

@Scooterswapshop

2 жыл бұрын

We order weekly, if there’s someone you want and we don’t have message us on the app. We can get it fast, or let you know if it’s on backorder. Italy closes for all of august so items are flying off the shelf

Do you guys have any tips for cvt tuning? I have a peugeot 2stroke 50cc scooter that revved really high had great take off and top speed on 13mm carb and 5.5g rollers it was pretty stock with a sport exhaust but it seized and the rear pulley tore apart so i upgraded while changing everything else now it has a stage 6 intake manifold, 17.5 carb, malossi multivar. Ive fiddled with the cvt a ton with rollers from 5.5g to 11g and alot of different contra- and clutch springs. It just doesnt pull like when it was stock if i put any lighter than 7.5g rollers on it, it will rev really high and it wont accelerate and top speed suffers greatly, feels like the clutch is slipping but im not sure. the belt sits pretty high on the rear pulley but it could be higher, ive also replaced the belt many times. Thanks in advance.

@Scooterswapshop

2 жыл бұрын

look up ScooterSwapShop cvt we have several videos

Hey! Love the videos! They help out a ton! Quick question for you or anyone in the comments. How much play or space should be within the clutch pads and bell? Thanks!

@Scooterswapshop

Жыл бұрын

There’s no spec really just make sure you run the right bell and clutch meant for your bike. When the pads look thin replace it

@nblaubach8378

Жыл бұрын

@@Scooterswapshop Thanks for the response man! Appreciate it!

what foot pegs are those?

Honda sh 125i 2009 original roller weight and dimension pls

One question please My 125cc yamaha lost its top speed. Start is soft and quick till 80kmph but after 85 it stops pulling :/ top speed was 95-98kmph jps checked Variator, rollers, sliders, band belt, and 1000rpm cintra spring and 1500rpm torque springs. Are the clutch shoes dead? 28k on clutch. But the 5hing is even with sport clytch shoe it wont climb to 95

@pakoyvlogofficial6011

5 ай бұрын

try using 1000 Clutch spring and 1200 Center spring, what yamaha 125cc you have?

I wish you guys would Stock parts for the New Honda PCX 157cc 4valve engine. It's a beast for a 4T.

@Scooterswapshop

Жыл бұрын

If you provide us with a list of available items we will. As of now I don’t think anything exists. Just a drive face and exhaust.

Nice 🙂🙂🙂

@Scooterswapshop

3 жыл бұрын

yeeeee

I’ve just recently bought a aerox 50 with a 70cc kit. Bike runs and idles perfect but struggles at top end as struggles to hit 35 to 40 mph just wondering if anyone would know anything that could be wrong with it. Thanks

@Scooterswapshop

2 жыл бұрын

cvt or carb tuning

Great tips as always, was gonna build a spring compressor for my clutch but now know I can just stand on it. Even got to see they're a pain if I did. That sure looks exactly like a Honda pulley

@Scooterswapshop

3 жыл бұрын

Glad to help

If u look at the video at 6:50 I believe the washer was on the outside. It looked like it was there when u took the nut off

@Scooterswapshop

3 жыл бұрын

cool

Hi, i just broke 1 of the 18 blades that the variator fan has. Does it unbalance the variator or can have any issue? Thanks in advance

@Scooterswapshop

2 жыл бұрын

It’s likely Not a big deal

@walterboczula8774

Жыл бұрын

@@Scooterswapshop could you please tell mi the inner size of the fixed sheave, because I just bought a Yamaha Axis fixed sheave which it is 16 mm and as far I know it has to be 13 mm. Thanks

I got yamaha aerox with one variator multivar mhr, what polie should i use? I've searched for a polie mhr but how do iknow if its the right one for me? Could u tell me wich one u used on that vídeo please!?

@Scooterswapshop

2 жыл бұрын

polie?

@piguita9261

2 жыл бұрын

I'm not sure if its that the name " rear pulley" but i meant the thing on the rear that gets the clutch where the belt work like variator but from the back. I was thinking getting the polini speed drive evoluton 3 but idk if it work, could u ginne ant tip please? Also my scooter still 50cc

When are we going to get to see the aerox again?

@Scooterswapshop

3 жыл бұрын

We had some major issues with the company who we got the bullet cases from. Delayed the project 6 months

how much grams rollers are in your varriator?

@Scooterswapshop

2 жыл бұрын

this was long ago its gonna depend on a bunch of variabbles buy a tuning kit from our website that will help you tune yours we have a whole video on CVT tuning

what type of speedometer you use?

@Scooterswapshop

3 жыл бұрын

on this koso

I woulda paid for the clutch spring to have broke Paul’s nose lol.

Isn't your clutch tool upside down? Put the pressing bolts on the other side of the clutch.

@Scooterswapshop

Жыл бұрын

No it’s correct, you can’t use it the other way or the pegs contact the clutch and the open section wouldn’t touch the nut

11:16 isnt that good ? i got the same problem there... clutch engages then in idle i guess| ???

@Scooterswapshop

2 жыл бұрын

hmm

There may be a lot of mods available for the Zuma prebug, but none of them make it less ugly. I'd like to see more stuff on your website for the Zuma 50F.

@wsmaga

3 жыл бұрын

Hahahahaha, the bugeye is the ugliest zuma yet. They should’ve called it something else but def not a zuma, and being a 4stroke 50 is completely worthless 😂.

@Scooterswapshop

3 жыл бұрын

Not to be the bearer of bad news but tue 50f is a really bad bike to build. Very little items for it not many people build them and it takes thousands just to get mild gains. They’re reliable but a major uphill battle

@burnone716

6 ай бұрын

lol pretty sure i don't know a soul that would consider the 50f better looking xd

Where did you get the red bolt's?

@Scooterswapshop

2 жыл бұрын

Off the shelf at our store

Does malossi clutch fit on original clutch bell

@Scooterswapshop

2 жыл бұрын

105 fits 105, 107 fits 107

@auuuajdoma139

2 жыл бұрын

@@Scooterswapshop thanks

@howdareyu

2 жыл бұрын

What's the stock size?

I made a torque spring compressor if you want to see it dm me

Hi there guys, just to say that as a matter of fact a washer should be placed between the clutch and the bell,I happen to recently have noticed that exactly when I was going through the instructions book of my Polini ceramic speed drive Evo 3 and I happen to have seen this technical drawing where it's clear enough that a washer with specific given measurements is advised to go in there.I was in awe as I happen to not have placed a washer in there after finishing the recent restoration I did on my Zuma. So I went and could only get a washer with a slightly minor thickness than the one mentioned in the instructions book of the Polini ceramic speed drive. Maybe the washer isn't supposed to be used when the scooter is equipped with a 105mm original (or not) speed drive like we see in the video. Please reply back to me on this issue as soon as you can.

@Scooterswapshop

2 жыл бұрын

message our app for support on products we can assit there or on our live tonight

Moral of the story: do your research and use the right parts..

Why the background music ? too much bass and interfering

@Scooterswapshop

Жыл бұрын

The guy editing the music is no longer with us there won’t me any more music

Aerox please

@Scooterswapshop

2 жыл бұрын

Coming soon

This video was just picking up random calls wasting my time lol i idc bout that im just trynna learn quick the guys was helpful but i had to be skipping a lot

@Scooterswapshop

7 ай бұрын

Yea we got rid of the guy who used to edit our videos lol

@Lil_eee

7 ай бұрын

@@Scooterswapshop oh man I feel bad but it was a nice video for y'all a little memory video/ tip video for us 😆

Paul’s hands are soft and supple and weak? 🤣 I’d imagine shaking hands with Paul would be like shaking hands with a seal 🦭

@Scooterswapshop

3 жыл бұрын

lol

I also got soft weak hands, because they're are mad to caress a woman cheek

@Scooterswapshop

3 жыл бұрын

women like rough hands hahah

Evil dead kinda country😂

Always talking crap in between.

@Scooterswapshop

Жыл бұрын

If you don’t like it don’t watch, it’s free media

@SkengManNZ

3 ай бұрын

Nar it's advertising for your overpriced parts

Hey bro, i'm India. I have 125cc suzuki scooter i need maximum top speed, so how i need to modify it