Scag Tiger Cub mower deck spindle hub/pulley removal and installation
This video shows how to remove the hub and pulley from a Scag Tiger Cub mower blade spindle.
Жүктеу.....
Пікірлер: 24
@deeboy437810 ай бұрын
I'm so glad I seen how you broke those bolts. . Before I did the same thing
@chrisMcG172 ай бұрын
I really can't thank you enough for this. Thank you so much. I got my mower fixed thanks to you
@aggiejet
2 ай бұрын
Excellent. Glad it helped.
@fernandomendoza24214 күн бұрын
❤ thank you so much
@madischulz Жыл бұрын
Very informative !
@stovar11822 ай бұрын
Thank you. That's good stuff.
@robertwilcox89029 ай бұрын
Thanks. The other video you refer to was missing all the pics of how it looks. This fit the bill. Thank you!
@aggiejet
9 ай бұрын
Glad it was helpful!
@robertwilcox8902
9 ай бұрын
@aggiejet I broke one bolt as well. Ended up having to drill and retap the hole. I found another video where they tightened the bolts and hit the pulley at the same time. Once I did that, it fell right off.
@kurtdussander4944
3 ай бұрын
My hub and pulley keep sliding down the spindle resulting in belt flying off. I know it’s just had so much use that it’s worn and won’t grip in place when I move it back up and torque it back down. Thought I’d check KZread and see if anyone else had this problem. Suppose I’m off to get spindle , hub n all for my 20 year old Scag.
@robertwilcox8902
3 ай бұрын
@@kurtdussander4944 This is a interference fit, so I can't see the spindle shrinking, but I could see the hub expanding. Maybe a new hub first? Lot cheaper. :) Good Luck.
@kurtdussander4944
3 ай бұрын
@@robertwilcox8902 you could be right on that. I definitely don’t see the spindle shrinking. I could see the metal wearing. The whole setup on eBay is $60ish and I will probably go that route. On another subject about how the gentleman spoke on measuring from top down for proper pulley placement,, sometimes you got to watch measuring from top down if it’s a secondhand mower because the spindle could’ve been replaced with one that has a different length shaft.
@jeffvanrobertson297016 күн бұрын
How hard was it to remove the screwdriver from the taper lock?
@aggiejet
16 күн бұрын
@@jeffvanrobertson2970 very easy
@bigdaddyhill7110 ай бұрын
I broke one of mine too! How did you get it out!
@aggiejet
9 ай бұрын
I was able to use a needle nose vice grip. It unscrewed easily.
@kennymacdowell12577 күн бұрын
How far do you set the pulley down the shaft?
@aggiejet
3 күн бұрын
20mm
@MelsML558 ай бұрын
His voice and draw reminds me Forrest Gump........not to be disrespectful at all.
Пікірлер: 24
I'm so glad I seen how you broke those bolts. . Before I did the same thing
I really can't thank you enough for this. Thank you so much. I got my mower fixed thanks to you
@aggiejet
2 ай бұрын
Excellent. Glad it helped.
❤ thank you so much
Very informative !
Thank you. That's good stuff.
Thanks. The other video you refer to was missing all the pics of how it looks. This fit the bill. Thank you!
@aggiejet
9 ай бұрын
Glad it was helpful!
@robertwilcox8902
9 ай бұрын
@aggiejet I broke one bolt as well. Ended up having to drill and retap the hole. I found another video where they tightened the bolts and hit the pulley at the same time. Once I did that, it fell right off.
@kurtdussander4944
3 ай бұрын
My hub and pulley keep sliding down the spindle resulting in belt flying off. I know it’s just had so much use that it’s worn and won’t grip in place when I move it back up and torque it back down. Thought I’d check KZread and see if anyone else had this problem. Suppose I’m off to get spindle , hub n all for my 20 year old Scag.
@robertwilcox8902
3 ай бұрын
@@kurtdussander4944 This is a interference fit, so I can't see the spindle shrinking, but I could see the hub expanding. Maybe a new hub first? Lot cheaper. :) Good Luck.
@kurtdussander4944
3 ай бұрын
@@robertwilcox8902 you could be right on that. I definitely don’t see the spindle shrinking. I could see the metal wearing. The whole setup on eBay is $60ish and I will probably go that route. On another subject about how the gentleman spoke on measuring from top down for proper pulley placement,, sometimes you got to watch measuring from top down if it’s a secondhand mower because the spindle could’ve been replaced with one that has a different length shaft.
How hard was it to remove the screwdriver from the taper lock?
@aggiejet
16 күн бұрын
@@jeffvanrobertson2970 very easy
I broke one of mine too! How did you get it out!
@aggiejet
9 ай бұрын
I was able to use a needle nose vice grip. It unscrewed easily.
How far do you set the pulley down the shaft?
@aggiejet
3 күн бұрын
20mm
His voice and draw reminds me Forrest Gump........not to be disrespectful at all.
They are bolts, not screws .
@aggiejet
Ай бұрын
So educate me. Whats the difference?
WOW, not the correct way .
@aggiejet
Ай бұрын
Care to elaborate?