Samsung Top Load Washer Won’t Stop Filling Diagnosis and Repair. (DC97-15459G)
Call us today with you model number and we will make sure you get the right part
888-655-8569
In most cases we can get you the part the next day if ordered before 4pm central time.
---------------------------------------------------------------------------------------------------------------------------------------------------------------
Donations are appreciated as well you can donate here - www.paypal.me/...
Here is a link to the water valve if you need it.
----------------------------------------------------------------------------------------------------------------------------------------------------------------
Link
Water Inlet Valve- amzn.to/2LClm5H
----------------------------------------------------------------------------------------------------------------------------------------------------------------
Stop by our Amazon store to pick up must have tools for appliance repair
www.amazon.com/shop/beardedappliancerepair
---------------------------------------------------------------------------------------------------------------------------------------------------------------
This samsung top load washer will not stop filling with water. The only way to turn it off is to cut off the water valve at the wall. 9 times out of 10 the issue is going to lie in the water valve. If you want to be sure all you have to turn is run the water valve and unplug the unit if it does not shut off you are looking at a water valve problem.
To be more clear. There are 5 different valve on this unit. To test them all you go into diagnostics. Hold “spin” and “soil level” and press power on. Let go of the other two and you will see all lights lighting up. This indicate you are in diagnostic. Once you are there you spin the dial clockwise twice. You should see “Tst” on the display. This is the service test portion of diagnostics. If you touch temp it will turn on the cold valve. Once again the hot so on and so fourth. When all the lights turn on, in the temp section all the valves are on. When they are out then all valve should be off. If you still have water coming through when the valve should be off than you have a bad water valve. Go ahead and swap it out. To be sure go ahead and unplug the unit. Again if water is still coming though than you need a new water valve.
Good Luck!
Thanks for watching, Like and subscribe!
Disclaimer:
I am a proud affiliate/sponsor of these products/services. All opinions and recommendations are honest and expressed with the good intent that you will find them of value. Purchasing through these links will not affect your check out process in any way, but it will support this channel and allow me to keep making valuable videos for you. Thank you for your trust.
Пікірлер: 122
Flawless instructions! Thank you sir, you saved a disabled veteran a couple hundred on this repair. 🙏🏾
My wife and I cannot thank you enough for making this video! Water was coming out the rear of our washer and also the water would turn on unexpectedly and fill the drum even when we weren't washing clothes. My wife discovered your video and put me to work. Saved us quite a bit of money and time. We are back in business. Much appreciated!
Your video, Samsung Top Load Washer Won't Stop Filling, helped me diagnose and repair my washer. Thanks 😊
2 years after posting your video and it's still being a game changer!! Great video, excellent instructions and problem solved!! Thanks again!!
@sarahabtom7849
2 жыл бұрын
Pq
@clintonscheible3146
16 күн бұрын
4 years plus now!! Saved me a good amount of money so I had to throw him a little cash. I think more people on here should. A visit alone from a repairman costs $60
These instructions were so good I feel like I could have just taken them and applied them to probably what is a basic valve system in washing machines. Basically, a standard "how to replace your washing machine water valve (probably)"
Very clear and informative. Repair cost me $35 for the part and 20 minutes of patience.
Thank you!!!! I fixed this all by myself and I feel unstoppable!!!!!
Found this video through a Google search, was able to confirm the diagnosis, ordered the part through your Amazon link and swapped it out in less than 20 minutes. Thank you so much for such an informative and short How To video.
Thank you! Great instructions. I clicked on your link for the part, but I was able to find one for 1/3 the price just letting you guys know. Thanks again!
@clintonscheible3146
16 күн бұрын
Yeah, that one is an OEM.... made the mistake of ordering it and finding a generic for 1/3 the price on amazon (1/4 buying local). Just google the part number. I could go through three generic valves before it costs me what the OEM costs.... Samsung has ALWAYS been like that (as much as I love their products and at the end of the day, most OEMs do this....
Super helpful tutorial!!! You just saved myself hundreds of dollars, sir. Problem FIXED! Thank you so much!!!
@BeardedApplianceRepair
3 жыл бұрын
Great to hear!
Have the same washer but my symptom was water was slowly leaking out the back of the washer even when the washer was off. Noticed the water was coming from below the external hose connections. I would also get water pooling in the detergent tray. Replaced this part and I am good to go! Thanks a million for the video - saved me a ton of time.
You just saved me time and money. Thank you for the simple breakdown and instructions. Nice work!
Thank you that was great information. Great education. He did a great job explaining everything.
Great video, very easy to follow. I was able to determine what the problem was and fix it myself. Just so you know, I’m no handyman. I have one screwdriver and a pair of pliers, thankfully that’s all I needed.
@BeardedApplianceRepair
4 жыл бұрын
Heck yeah! I love it. Appliance repair is not bad. Most calls anyways. Some give you trouble but most are fairly easy if you know what to look for. Glad we could help man!
Hey there! I had this same issue, where one of the valves wouldn't close and the washer kept filling. I looked up the problem online and found this video. After confirming that it was indeed the issue (by following your troubleshooting steps), I ordered the replacement part. Your walkthrough was perfect, and I'm happy to report that the inlet valves have been replaced and the unit is working again. Thanks so much for the helpful video! That really helped me out. =)
@BeardedApplianceRepair
4 жыл бұрын
Man yeah. Got the donation. Thanks so much!
Very good video! Your instructions were SPOT on now the washer is fixed!!!
4 year old video so helping! Thanks for the video
Hreat troubleshooting video. Unfortunately, I'm still habe an issue with the water not shutting off. All valves shut when tested but during operation, the water won't stop for the designated load amount. Any other tips?
You communicate really well. Keep it simple. Thanks.
Thank you for this great video, spot on and easy to follow!
This was an excellent video. It is exactly what I needed to fix my washing machine. Thank you for this! Just subscribed!
Thank you so much.
Can't say enough thanks man. You're a pro
Hey thank you for the help I have this exact washer and I’m having problems with the I think water level sensor? It fills up fine and when I push pause it stops but it fills up to the top and doesn’t stop any input?
The problem is not with filling the washer. The problem is that it fills and empties then repeats in a continuous cycle and then pauses with an 8B error code.
Thank you!!! 🎉
What tool are you using to unscrew?
Thanks to your video i replace the part today and good as new!! I really appreciate this tutorial!
@BeardedApplianceRepair
3 жыл бұрын
Great to hear!
hey thanks man the video really helped got the peace today and it took 5 mins to install
So mine is a bit weird. It drips water for like 5 seconds randomly then stops. I ignored it for like two days until today I just looked in the washer and it had a pool of water 😢 Would I still do this kind of repair? The water shuts off when I tested it like you in this video. :(
Thanks!
Would changing the inlet valve apply to the blue colored spout where the rinse water comes from? This is the only spout that doesn't stop running sometimes
Thanks for the advice!! Worked out great!! Saved me serious $$$$$$$$
Thank you for this. It helped me a lot.
Thanks for the help!
I'm having the same problem, water not shutting off. I'm going to replace that water valve to see if that fixes it. Good video.
@BeardedApplianceRepair
3 жыл бұрын
Did it work?
@raulvega1623
3 жыл бұрын
@@BeardedApplianceRepair Yes it did, thanks, awesome video to about 45 minutes. You're awesome saved me time and money, only paid about $40.00 from amazon.
@maurice6288
2 жыл бұрын
@@BeardedApplianceRepair I just ordered one I was getting am nf1 error code
Thanks so much - this video saved me a bunch of money! So, Roll Tide, I guess 😂
the part the valves go into are cracked. could you tell me the name of the part to replace?
I have same or similar machines but my display leds are not lighting correctly zones so I can't read time or select mode what if a fix
I tried pressing both spin and soil, then the power button. (All together) Mine will not go into that test mode. I did some more research and went to 17h delay (start for 10 seconds) then it went to a whole test mode. No leaks no issues. Could this have been a random fluke? It was a lot of water seemed like it came out over the top. I did follow the water trail.
Great video...Everything went exactly as you said and the water turns off with the test, however no hot water comes out at all now ...suggestions?
@BeardedApplianceRepair
3 жыл бұрын
Make sure you have good hot water pressure. If you do than I would think you have a bad water valve.
very helpful. roll tide!!
Hello thank you for the video my washer is doing exactly that. Where can I find the part ? Amazon or where. Thank you 🙏
I followed these steps worked great but now when water goes to the softner it will not stop flowing and this is with new water inlet valve, any suggestions?
SONI did this but the water shut off when I unplugged it but it’s stuck on the wash cycle
MUCHAS GRASIAS POR EL VIDEO 😁
Where did you order part?
So I have this washer , same problem water keeps filling but when I did your diagnostics, at the last push my water did turn off, what does this meab
Great vid mate. 👌👍
Great video and roll tide
@BeardedApplianceRepair
3 жыл бұрын
War Damn Eagle! Thanks lol
I tried the test you detail. My issue is when cycling through all the lights don't turn on after pressing the temp button. The water runs on cold, hot, etc., but never all lights on as described. When I finish the last push the water does stop, after slowly running about 30 seconds. Does this mean I have a defective valve, and should I just replace the part?
@thatonefunnygirl1829
Жыл бұрын
That is also my issue. I don't want to buy a part that will not fix the issue.
Hello sir! I followed your video and I’m not sure this is my problem… My washing machine will rinse and spin repeatedly without really spinning… is that a fixable problem? Thank you!
I'm working on one that doesn't turn off while in quick wash mode but turns off when the power is turned off. Could that be the water fill sensor not working correctly?
I have the exact same Samsung model. My issue is that it leaks from bottom. I’ve checked the hoses (secured and clamped), the hot and cold inlet valves, and the detergent tray. My drain pump is good shape, no blockage. I didn’t know about the diagnostics feature. Will the diagnostics give me an accurate reading on the problem? As of now, I get a 4E error as well. Any further advice is appreciated. Thanks!
@BeardedApplianceRepair
4 жыл бұрын
If it’s filling with too much water you have a somewhat complicated issue. The pressure switch monitors the water level and it could be a number of different reasons why it’s not working right. Hopefully you just have a bad valve. So if you’re not getting water then it will be easier to diagnose. Make sure your water valve(s) are working and that the pressure is good. The leak can even be the cause of the error if it’s a serious leak. The water may be leaking as fast as the water is coming in. I think you would have been able to find that leak though. It’s probably small. Try and find the leak by just following the water trail. There is a panel in the back. You can take that off and look underneath the washer and see where the water is coming from. Looking for any drips would be the way to start. Gravity should show you the way.
@shirocp
4 жыл бұрын
@@BeardedApplianceRepair Thanks! I checked all my hoses and valves, I guess there was a hose that was loose, and I didn't catch it the first time around. I replaced the clamp so that the hose would be more secure. I ran a load and it was successful. No more leaks! I appreciate the feedback. Thanks for sharing.
Hello I replaced the water valves! Proud of myself! Great video, but it still overfills when the temp is on either eco warm, warm, or hot. Any other ideas of what it could be or how to fix? Thanks in advance!
@lisaschroth4097
8 ай бұрын
Did you ever find out what it was? Was it the pressure/Level switch? Mine is doing the same thing as yours and I want to avoid swapping out a part that I don't have to.
@WoodsyWoodson
7 ай бұрын
@@lisaschroth4097same here. Cold water shuts off fine. Hot does not, but they all shut off like they should when doing this test. Tells me it’s not the valve or pressure switch. I’m leading toward it being the control board but like you don’t want to just throw parts at it, process of elimination style.
Thank you SO much!!!!
You are awesome !!!
Do you have a link for the part?
Do you show how to repair other codes?
@barbarac3971
11 ай бұрын
I have the nF code
What if you can move the sensor buttons up or down
Where did you order the replacement part from?
Podria aser un video de como volver a programar una lavadora samsun como esta en español
Mine wouldnt stop filling and i changed the water valves and the pressure sensor and it still does it but now it throws a 4E code
@chels_reallife4816
Жыл бұрын
Same
Pro tip verify which water valve yours has because no matter how similar they look for whatever reason you can’t use the 15459g in place of a 15459h. Your machine somehow will know and it will take forever to wash and your wife will treat you like you’re stupid and broke her machine worse than it was prior and make you put the messed up valve back in it. Don’t ask me how I know this.. 😂
Bro... What do we do if the water pump doesn't stop pumping? What ever mode it's just pumping...
I’m not getting a code, it just won’t drain the water and it’s making a odd sound...thoughts?
What is the part number?
Thanks for the help. And ROLL TIDE!!!
@BeardedApplianceRepair
4 жыл бұрын
War Eagle!! haah
@maurice6288
2 жыл бұрын
hello there I just ordered a new water valve for it I got an nf1 error code hope that's the problem thanks for the video
Cam u tell what this error codes are 8b 0d
Where can you learn all those diagnostic mode?..very good job i watch all your videos
@BeardedApplianceRepair
5 жыл бұрын
Tech sheets. If you can get your hands on those it will tell you everything you need to know. Well everything you need to know in regard to how to test things. Samsung washers in particular the are in a bag located on the rear of the machine. A lot of times they will be missing, but heck yeah if they are there. Every brand is different on where the tech sheet is located. Starting this year whirlpool is not going to push tech sheets on washing machines. They are going away so if you really need them you can join appliantology.org/. If you’re a member you can either request or look up tech sheets for help. Even ask for advice on certain issues you’re experiencing. Glad to be of service C G. Thanks for the comment!
@cris.g4608
5 жыл бұрын
@@BeardedApplianceRepair thank you so so much
I have a washer very similar to this, but my issue is that it won’t turn on. It plays the chime of turning on, but no lights. I have attempted to fix it and see the main control board receives 120V. A green light flashes every 5 seconds on the board and when I attempt to turn on the washer on, another green light flashes for 3 times, on the third flash it seems to get cut off short. Any help would be greater appreciated.
@BeardedApplianceRepair
4 жыл бұрын
That's a good question. When it comes to these it could be either the panel or the board. The panel is what I would start out with. It is risky either way your gambling with it but us as techs do it everyday lol.
thanks for yours service sir ....x10
@BeardedApplianceRepair
4 жыл бұрын
Glad to help Flores Family!
So I have tested the water supply valve and it functions properly. I also checked resistance on it and it is within spec. The supply lines are clear of debris. The only thing left is the circuit board, that I’m aware of, is that pretty common?
@BeardedApplianceRepair
4 жыл бұрын
will it continuously fill like in the video? If so the control board is very rare to fail in that case. I am sure it can happen but I have not personally seen it in the field. Try again to see if the water valve sticks open when power is un-applied. sometimes you have to try it numerous times to get it to duplicate the issue.
@Aayala7685
4 жыл бұрын
I’ll have to try again tonight. But I ran it through the water valve test cycle 3 different times and it did shut off all 3 times.
Awesome
If I heard the instructions correctly you said "Of course you do want to unplug the machine BEFORE working on it"????
What's the part number for that valve assembly?
@BeardedApplianceRepair
3 жыл бұрын
part number is in the title of the video
Excellent video !!!!!
@BeardedApplianceRepair
4 жыл бұрын
Thank you sir!
@marka8486
4 жыл бұрын
ROLL TIDE !!!!
@BeardedApplianceRepair
4 жыл бұрын
Mark A we did! Compliments of Auburn on 11/30/2019. War Eagle!
What code is this?
I tested mine but the water stops. My mom said it was leakin yesterday and wouldn't drain. How would I test the motor? Just start an empty cycle and hope for the best? Lol
@BeardedApplianceRepair
3 жыл бұрын
Those pumps are notorious for going out. I replace a lot of them. Run a drain and spin and see if you hear the drain pump motor running. If you do likely it is the pump. Could also be something down in the housing. Take it apart to find out.
@ladyshalay6370
3 жыл бұрын
@@BeardedApplianceRepair I did. I fixed it. That little clear hose, that measures the water pressure or level, had come loose. I put it bad on and now it works. Thanks for the replies and help sir. Greatly appreciated
I have the same machine and it keeps giving me a 4e code
My machine wont let water in....is that same issue?
@BeardedApplianceRepair
3 жыл бұрын
Could be yes. Make sure you have good water pressure at the wall. Usually it is either the hot or cold that is not working. I reckon it could happen but if both hot and cold don't work it may be as simple as turning the water on.
My water don't turn off no matter what even when I turn both the knobs. 😔
@BeardedApplianceRepair
2 жыл бұрын
Need new valves on the wall then. You will have to shut the water off to your whole home to get it to stop.
Turn The feed water valve ALL THE WAY OPEN, that should "back seat" the valve to get it to stop leaking!
Error code 8b
Mines keep repeating rinse and spin these samsungs are a piece of junk
Thanks!