20 years in the transmission industry i have to say that it hurts to watch you guys take off the snap rings. I just know that 20 years ago i was the same way.

@SomewhatHaggard

Ай бұрын

Yeah it was rough! We did another gear reduction a few weeks later and it went a lot smoother. I bought better pliers and it made a huge difference.

best video ive seen yet, good for you two! This is how most of everyone is going to be preforming this type of modification. in their home with an old cutting table and two guys that say "fuck it! Lets do it!"

@SomewhatHaggard

3 ай бұрын

Thanks!! We appreciate it!

Awesome video. Great advice by you. Where did you get that little airbag

@SomewhatHaggard

3 күн бұрын

Thanks for watching!! That was an Amazon special!

great job guys

@SomewhatHaggard

Жыл бұрын

Thanks!!

Ugh. I followed all your guidance and recommendations, but you said nothing about needing the AA alignment tool. Am at the rebuild phase and just paid for expedited shipping. Definitely do appreciate all the tips you did provide! Hope this comment helps others.

@SomewhatHaggard

Жыл бұрын

Dude attempted to buy the tool but they sent the wrong one. We did some research and talked to a guy that does gear reductions all the time and he said it’s not necessary. All the bolts align the motor and trans. On the non-turbo machines it’s absolutely necessary from my understanding. Ultimately we did both gear reductions with no alignment tool and had no issues

@RedSound2011

Жыл бұрын

@@SomewhatHaggard OK, thanks man, I'll move forward to close this up, and fall back to the tool if needed.

@SomewhatHaggard

Жыл бұрын

No problem, we wanted to double check as well but when they sent the wrong one we started looking into it more. It’s probably the safest way to do it, just to be sure.

Cracked up when you patted the piece of bread 🤣

@SomewhatHaggard

Жыл бұрын

Haha yeah it was a long battle with that clutch! I was happy it was over!

Great job are you and dude brothers 🤔

@SomewhatHaggard

Жыл бұрын

Thanks!! Haha no we’re just 2 bearded fellas.

What lift do you have it up on? That would make life much easier than wood blocks and jack stands.

@SomewhatHaggard

Жыл бұрын

Yup it sure does!! It’s the tusk utv lift.

When will you do a review on it?

@SomewhatHaggard

Жыл бұрын

I plan on going over what we think once we use it in some real terrain, we’ll be in Tackett creek beginning of April so I’ll be sure to address it then. It’s not on the channel yet, but since this video we did it on the other pro xp on the channel as well.

Boring af but watched every minute good info man

@SomewhatHaggard

Жыл бұрын

Haha thanks!! I know it’s not the most exciting subject. I wanted to try and cover everything, I know there’s some people that may not know where to start on a project like this.

Where did u the gr and how much was it?

@SomewhatHaggard

Жыл бұрын

I don’t remember where Dude got his set up. I got the same gears as him from partzilla and I got the high speed shim and pinion retainer plate from xit off road. I think all of the parts were around $560.

@craigwoll5041

Жыл бұрын

@Somewhat Haggard gr on my to do list, but next is rsc cage. Thanks for the info

@SomewhatHaggard

Жыл бұрын

No problem!!!

How is it the wives are clear as day throughout most of the video but Dude doesn’t say a word? Lol

@SomewhatHaggard

Жыл бұрын

Yeah it’s a special talent of his lol. Even when he does speak it’s soft. He says stuff and it doesn’t even show a waveform while editing lol.