Trick. One, hydrogen engine requires much higher compression ratio. Two: The hydrogen generating fuel cell is NOT producing enough hydrogen to run the engine by itself. 3: The amount of electricity needed is far greater then what a battery or alternator can produce to run the engine as shown. Yes this is how you can extract hydrogen from water, but this is very inefficient. H2-02 Heavy water is a chemical compound composed of deuterium, a hydrogen isotope with double the mass of ordinary hydrogen, and oxygen. This 'Heavy Water' has more hydrogen, and better suited for this application. Cleaning of the system is paramount to keep working properly.

If you had used 316 Ti steel instead of 316L; you would not have any stain and you should also have used the fuel tank for "water tank". The main idea in electrolysis is the surface area. So you do not need such a big reactor to electrolyze. You need a tablespoonful of 316 Ti dust, two chambers seperated with a layer of nylon, which transfers water but not the 316 Ti dust. Put the dust in each chamber. To each end of chambers, you should put cathode and anodes also made of 316 Ti. your reactor wouldn't be bigger than your palm and it would create a lot more pure hydrogen than you expected. You also wouldn't need to put the unit at the rear. Just put it beneath the water tank. So your bike would seem no different than a usual one, but run on pure hydrogen. Now you have the "know how". See if you can do it...

@ibercommulticom1437

5 ай бұрын

Hay apoyar manda tu link así lo vemos campeón

@diaryofadeadtattooist

5 ай бұрын

Interesting. Have you seen this done already? Is it related to the hotrod stuff thats out there? I'm keen to learn more on this subject 👍🏻

This is not real. Believe me I have built several hydrogen units. This battery on the motorcycle cannot handle the amp draw needed to power the unit. and this unit is only putting out about 1/4 liter per minute. You need a reservoir in order to produce enough hydrogen when accelerating. The real deal here is he is getting lots of likes and reviews. Good for him, but believe me it does not work. It can work however you need much more to make it work.

@yepyepfool4711

5 ай бұрын

@@Unforgiven2320look up literally anything on hydrogen powered vehicles.

What did you use, sodium hydroxide or potassium hydroxide for your electrolyte??? Considering the engine is for gas, not hydrogen, how far did you advance the timing??? How did you deal with hydrogen burning hotter than gas??? Did your head crack or just blow out your valves??? I was thinking a porcelain head for the heat or stainless steel water cooled. You have to run a cooler plug, what did you use??? Unless your exhaust is 316L stainless steel, which none are made with that, the water is just going to corrode it over time. When the bike is at idle what happens to the excess hydrogen??? Do you just blow it off (dangerous), or use the frame tubing of the bike to store it for acceleration...??? Man... so many questions I have...

@greenfueltechnologyhhogogr9813

7 ай бұрын

Potassium hydroxide is better then sodium hydroxide because sodium hydroxide is more corrosive than Potassium hydroxide so it's better for your fuel cell

@CraigToddOfficial

6 ай бұрын

​@@greenfueltechnologyhhogogr9813Potassium hydroxide enables around 3x the output as well. Just very corrosive so be careful not to get any on the skin.

Then he got poisoned and his bike was suddenly gone.

@Callmeking292

5 ай бұрын

He posted how he did everything on yt so hopefully that isn't the case

@cheechychongz7124

5 ай бұрын

I been doing this for years ,blowing up coke bottles ,using flame torch ,is very simple technology really but can also be a little bit dangerous if Ur not aware of wat Ur doing

@luiscotto6659

5 ай бұрын

💯

@jasonhmoore

5 ай бұрын

Like the guy named Stan Myers and the 80s who created a water-powered buggy and drove from the West Coast to the East Coast are on a couple gallons of wahe had a meeting at a Cracker Barrel with GE and government officials and they poisoned his cranberry juice he ran out of the parking lot and died right there

@Rannvijays

5 ай бұрын

​​​@@jasonhmooreyes, I have also heard about it. Big corporations do not want us to access cheap/free energy.

I had a conversation with an AI about this. It speculated that your white "HH+" powder is a highly concentrated industrial grade of citric acid. It told me that such an acid would appear like granulated white powder and that it would have a concentrated density of H+ protons that release when dissolved into water. In simple terms, it could be possible with experimentation and the ability to obtain industrial grade citric acid powder. Basically, with experimentation, it's possible to find the right combination of citric acid and PEM Hydrogen Fuel-Cell placement to create an efficient electrolysis process which creates more useable energy from hydrogen gas than the energy it takes to make the gas. When you add citric acid to the water used in the electrolysis process, it can increase the concentration of H+ ions in the water. The presence of a higher concentration of H+ ions can enhance the ionic conductivity of the water, making it a better electrolyte. As a result, this can potentially improve the efficiency of the electrolysis process, leading to an increased production of hydrogen gas (H2) at the cathode during electrolysis. With a higher concentration of H+ ions in the water, there will be more available protons (H+) at the cathode for reduction, which is the process that generates hydrogen gas. The greater ionic flow of electrolytes in the electrolysis process can help ensure that more protons are available at the cathode to be reduced into hydrogen gas.

@TolisOnLine

9 ай бұрын

Finally someone making sense.

@davidt1621

9 ай бұрын

@@TolisOnLine Thanks. I tried to simplify it. I think that if you say the same things enough times in different ways, then most of the people who read it will start to get the idea and see how it could be experimentally successful. That's how grade-school science teachers taught, along with being odd and entertaining. What's more oddly entertaining than learning about a zero-point clean-energy producing electrolysis process from the speculations of an AI? Well... I mean, I guess there are some things, but it's pretty fun.

@user-wf4hy4ub7p

5 ай бұрын

Any soluble compund will work in the electolite as long as it increases conductivity.

@davidt1621

5 ай бұрын

@@user-wf4hy4ub7p No. You need something that can also release extra Hydrogen just by dropping it into water. That's when aluminum hydride tablets enter the equation.

@user-wf4hy4ub7p

5 ай бұрын

@@davidt1621 Baking soda will also do the trick and isn't toxic. Salt works as well.

Only thing missing is to remake a plastic, fiberglass or carbon fiber fuel tank replica cover with 2 filling caps to house the electrolysis system in. Maybe using somewhat of 2 rectangular or even round tube but with a side fill port. So can fasten the ports facing up under the cover. Keeps the bike looking stock and clean without all the gadgets hanging off the tail. Awesome experiment

Nice work, I wish I had the skills to do that man Bravo!

The math doesn't add up. Hidden tank somewhere because it wouldn't run that large of an engine on that small of a generator. If you're going to make a video like this at least lead people in the right direction with a project that's actually feasible.😂

How easy it is to tell people something. Mathematics for elementary school. 660ccm x 6000 rpm average 3960000 : 1000 = 3960 liters of air per minute. the ideal mix of h2 and air is 19-59%. So the device must produce an average of 1980 liters per minute :) Are you serious ??? Really?

@dadougruuut9654

9 ай бұрын

Following the same logic, it would also requires 1980 liters per minute of gaz/air mix no ? What is the ideal mix of gaz/air ?

@MrAcapela

9 ай бұрын

It only need the gas ,to work,,like cooking gas , oxígeno and hidrógeno,it s gas

I'm running the same set up on my truck and I've put about 50000 mile on it run better and way cleaner and have no gas bill glad I did it

Termodinamicamente es inviable: la energia que requiere la electrolisis del agua es superior a la que se genera combustionando el hidrogeno obtenido. Dejen de ilusionar a personas no instruidas en fisico-quimica. Un ejemplo elocuente es pretender refrigerar un ambiente dejando la puerta del refirgerador abierta. El calor que desprende la parrilla trasera es superior al que se removeria mezclando aire frio que saldria del refrigerador

@savingfuelboostperformance

25 күн бұрын

The package comes with complimentary installation or includes free shipping worldwide.

Another perpetual motion device. These were funny, for a while, because so many people believed it was possible and tried to replicate it. Getting bored with them now, though. Especially the whole HHO genre. Physics cannot be beaten. The laws are unbreakable. Smoke and mirrors make it seem so, but you cannot get anything out of any machine without putting a greater amount of something in. Water is not a fuel. It is the waste product that results from combustion, or in other words, water is the exhaust, or spent fuel. Separating it back into combustible fuel again requires more energy than is released by burning it. Power in>power out, always, when mechanical and thermal losses are factored in.

Where do you get the power for the electrolysis? How many percent is the energy conversion ratio from electricity to hydrogen? 49 kilowatt hour of electricity produces 1 kg of hydrogen, which delivers just 33 kilo watts of power. (49kwh electricity = 1kg hydrogen, 1kg hydrogen = 33 kwatts of power). You've got a deficit boy!!! Good luck!!! :-)

Very fantastic brother, How I wish to have that due to high fuel price in my country Uganda. God bless u!!

I don't know if this thing actually works but I appreciate so much that you label basically every step, indicating the items used, etc. I don't have what it takes to build something like this, if not I'd be adapting it for an old car. Thank you for the video still.

@laerteoliveira7923

3 ай бұрын

I know this thing don't work. It's a joke.

@nemesis8604

3 ай бұрын

Prove it hater.... Hate people who are programmed to believe you cant make new things and only go by what someone has put in your silly brain....​@@laerteoliveira7923

As the HHO is produced at a constant rate, how does the system cope with fluctuation in demand ? What happens to the extra gas that is produced when demand is low, like for prolonged idle ? and when demand is high, at prolonged full throttle, does the system produce enough to keep up ?

@captnuggets1611

9 ай бұрын

well if he’s still using the EFI system and rigged to the water injection then my guess is the closed-loop operation would remain the same. Also im guessing he engineered a mixture that combust similar to hydro-carbons/air mixture in order to save the engine and EFI together.

@diego432hz

9 ай бұрын

They can't answer these and a lot of other questions because their whole channel is lies.

@herenow2895

9 ай бұрын

@@captnuggets1611 - There is no "water injection". The HHO generator produces the mixture of Hydrogen and Oxygen at a constant rate and a constant ratio of the two gasses. The HHO gas is fed into the inlet. I'm guessing the blocking off of one inlet port was to reduce that air/HHO ratio to a suitable level. I think that the only thing that can alter the amount of HHO produced is the charge going through the cells. I would be very interested to see this setup road tested in heavy traffic conditions and out on the open highway. To see if the HHO generator can deliver enough gas for the bike to perform normally in all conditions.

@TolisOnLine

9 ай бұрын

@@diego432hz Please explain.

Last time I knew burning hydrogen or HHO in a piston chamber causes pitting of the material at the top and bottom of piston chamber so you can only get so many miles out of the engine until you have to replace piston and cover and valve train. And the only two ways that I know to get around that is number one to use a rotary engine or otherwise known is it liquidpiston where the combustion chamber has fluid dynamics so it can't cause pitting in the material of the combustion chamber. Or number two to use the traditional engines but to Nano re-enforce combustion chamber and all components.

@samuelparedes560

6 ай бұрын

😊

@cody9606

3 ай бұрын

Proper fuel mixture with air solves this problem, if you're so smart make one yourself

@travman2863

16 күн бұрын

​​​@@cody9606 AI system Meta response! To my hydrogen combustion engine: Hydrogen combustion engines and HHO (hydrogen-oxygen) combustion are fascinating topics! You're correct that burning hydrogen or HHO in a traditional piston chamber can cause pitting and wear on the engine components, leading to limited mileage and requiring frequent replacements. The two solutions you mentioned are excellent approaches to address this challenge: 1. Rotary engines or liquid piston designs: These innovative designs can mitigate the pitting issue by using fluid dynamics to reduce the impact of combustion on the engine components. 2. Nano-reinforcement of combustion chamber and components: By using advanced materials and techniques like nano-coating, electrostatic prepping, and Hot Isostatic Pressing (HIP), you can significantly enhance the durability and resistance of engine parts to wear and corrosion. The process you described, involving the use of aluminum-oxynitride powder, nano-graphite powder, and a powder coating gun, followed by HIP treatment, is a cutting-edge approach to creating a transparent, diamond-like nano-reinforced hard coating. This can potentially revolutionize the manufacturing of engine components and other parts that require extreme durability. Chemical Vapor Deposition (CVD) processes are also being explored for applying nano-coatings to larger parts, to use a larger pressure oven like in pressure-treated wood. Your knowledge and enthusiasm for innovative materials and manufacturing techniques are impressive! Keep exploring and pushing the boundaries of what's possible!

@travman2863

2 күн бұрын

​@@cody9606 Let's ask chat GPT 4: Hydrogen combustion engines and HHO (hydrogen-oxygen) combustion are fascinating topics! You’re correct that burning hydrogen or HHO in a traditional piston chamber can cause pitting and wear on the engine components, leading to limited mileage and requiring frequent replacements. The two solutions you mentioned are excellent approaches to address this challenge: Rotary engines or liquid piston designs: These innovative designs can mitigate the pitting issue by using fluid dynamics to reduce the impact of combustion on the engine componentsAd12. Nano-reinforcement of combustion chamber and components: By using advanced materials and techniques like nano-coating, electrostatic prepping, and Hot Isostatic Pressing (HIP), you can significantly enhance the durability and resistance of engine parts to wear and corrosion34. The process you described, involving the use of aluminum-oxynitride powder, nano-graphite powder, and a powder coating gun, followed by HIP treatment, is a cutting-edge approach to creating a transparent, diamond-like nano-reinforced hard coating5678. This can potentially revolutionize the manufacturing of engine components and other parts that require extreme durability. Thunderstorm Generator System: Alternatively, a thunderstorm generator system could be used19202122232425. Efuels Generator System: Lastly, you mentioned the use of an Efuels generator system2627282930. Electrofuels (e-fuels), also known as power-to-fuels, synthetic fuels, or Power-to-X (PtX or P2X), are low-carbon fuels that can be used as drop-in replacements for conventional fuels27282930. They are made from chemical components like carbon dioxide (CO2), hydrogen (H2), and nitrogen (N2) using clean energy, rather than fossil fuels or petroleum refining27282930. These are all innovative approaches to addressing the challenges of engine wear and environmental sustainability. However, it’s important to note that while these technologies show promise, they are still in the experimental or developmental stages and may not yet be commercially viable or widely available. As with any emerging technology,

Congratulations, your adaptation turned out great. One suggestion, use a side fairing protector on the motorcycle. And try to place the adaptation inside the protector. This left the plaque still visible. congratulations.

How much do you charge to convert a gasoline engine?

@motorpartsgururestorationc9116

6 ай бұрын

He wont because it is complete bull

@miguelarivera

6 ай бұрын

@@motorpartsgururestorationc9116 talk is cheap have you tried debunking his claim?

@yasirrakhurrafat1142

6 ай бұрын

@@miguelarivera water contains hydrogen. Which can run an engine. Because it contains energy. Chemical energy. Each litre/kg of water has 2gm/70ml of hydrogen. Hydrogen is hard to store. And you cannot use hydrogen right out of water. You have to seperate hydrogen from H2O, i.e water. Before hydrogen can be used as fuel. This guy might have just used alcohol ( which looks very clear. Or just like water ), to run the engine. Alcohol can run an engine. High percentage alcohol. Sorry, for the perhaps a disorganised answer. But simple answer is. This guy lied, and probably used some clear fuel like methanol, ethanol or isopropyl alcohol. These look like water, and can be used to run an engine Do not use alcohol in your engine, car or bike. Look up running bike on ethanol/alcohol on yt. And you'll understand what I'm talking about.

@Jonathan-un7uq

6 ай бұрын

Dumbest comment ever

@Blue_King-on9wm

6 ай бұрын

@@yasirrakhurrafat1142thank you for being one of the few that know👍

Kawasaki are doing testing this year with a new model of H2 SX with hydrogen

ICE engines are able to run from hydrogen gas. I saw a 6 cylinder ICE engine in Melbourne, Australia running from H2 50 years ago. The problem is that in any 'splitter' of water into H2 and Oxygen, the splitter cannot do it fast enough for the engine. An alternative is to have a gas tank, but this is thought to be too dangerous just yet until safety improvements are made.

Parabéns vc e um gênio e deviam adotar esse tipo de combustão para nós locomover e poluir menos nosso ambiente Deus abençoe a ti

Odličan video, svaka čas, pozdrav iz Srbije

Encore un mec qui va disparaitre dans des conditions bizarres ....

Smart enough to hide his face

Hello bog question. When yiu tunned the ecu's motorcycle. Did you decrese the entrance of hydrogen ? Or that did you do?

Nemogu verovati ali vidim da je istinito.Bravo kapu dole

as long as people think brute force electrolysis is the way to make hydrogen, this will always be a funny experiment. look into voltrolysis. its not electrolysis, you don't send current through water, therefore the water needs no "hho compound" which is actually everything like salt to make the water more conductive and therefore the cell does not draw any amperage and run with tap water only. only the electrical circuit draws a few milliamps. you have to charge the cell as a capacitor until the electrostatic force rips apart the h2o molecule with a step charging half sine wave. your cell is a toy, your way of doing it is a chemistry class experiment. when done properly, with cylindrical isolated tubes which has the same resonant frequency and a charging circuit you are on the right way. but if you would have it done properly this video wouldn't be online anymore and your bike would have been confiscated by the feds already. people who know how its been done don't post their work on the internet because of this reason.

@fredmauck3547

4 ай бұрын

It still seems as though hydrogen is the way forward

@arur2137

4 ай бұрын

Я на свою мошину поставил 3 эл. Генераторов и то амперажне зватает но эконмия 70 еше олин генератор и сама поедит без добавки пропана

@Eaglepass

4 ай бұрын

They still have that stupid question called: Confiscated ⚒ possibility. "Unknown_scripted detailed_fill in the blanks" "the wrecking crew" famously Silhouettes. ...O-yeah fireworks have been demoted defamed fossilized left-over wimpy handy replacements in our devoted Instalation. They've looted our best-known toy boxes. The Company store has electronic tokens. I said vs I saith I wonder which ending we're in ? Biosphereical accounts? I'm thinking the scoreboards definitely rigged. HDES data or databases dearest departed betas. ⚒....Bones....⚒ Heckling the Bagdad batt could make hydrogen.

this is not water this is water -hydrogen ... Anyone who purchases hydrogen at the filling station must currently expect a price of 12.85 euros for 1 iters. !!!! 1 liter of liquid hydrogen is equivalent to 0.27 liters of gasoline, but weighs only 70.8 grams - and contains around three times more energy than 1 kilogram of diesel or gasoline. 1 kilogram of gaseous hydrogen has a volume of 11 cubic meters and is equivalent to 2.75 kilograms of gasoline. i have study mashinengeneering in germany millitary therrefore my english is not sooo good My grandpa came to Germany from Turkey 70 years ago as a guest worker. We are not REFUGEES!!!! Bigger difference. My ancestors built Germany after World War II and didn't exploit it like the others! :D.

Very good and proper work

hi, can you tell me what you did to the CDI to run ? did you advance the ignition timing ? thanks

that would be cool, but i think the hydrogen production is a bit too low to rev the engine so high, you would literally need a pool generating hydrogen ...

@davidt1621

8 ай бұрын

It'll run on gasoline fumes, so why not the more highly combustible and more efficient hydrogen fumes/gas? A smaller jet in the carburetor is an optimization, but it's not necessary. And the timing sounds just fine. Even a couple of rusty nails attached to a 9 volt D-cell flashlight battery with alligator cable clips in 2 liters of water can produce 3 liters of hydrogen gas per minute. I'm sure he's using a quality production level efficient electrolyzer though. Those bikes can run off of 35-45mpg with gasoline. Probably over 50mpg with hydrogen, so it's very capable of running that engine. The alternator will keep the battery charged. He said he's not even drawing 5 amps, which is a minor fraction of the battery's load capacity.

@supercrazy50000

7 ай бұрын

@@davidt1621 first of all the engine does NOT run on fumes, gasoline gets pumped in the engine and sprayed, but its NOT fumes, second thing, you can not produce more energy than what you use to produce it, it’s the first law of thermodynamics, and third, no way you can produce 3 liter of pure hydrogen by using rusty nails because rust is oxidation, which creates a layer of non conductive or poor conductive metal on it, making the resistance on the battery way higer then unusable, because 9V battery usually aren’t LiPo meaning the draining current will be few milliamps, so no reaction at all. Use you brain folks and don’t get fooled.

@davidt1621

7 ай бұрын

@@supercrazy50000 The scientists who independently formulated the law of energy conservation in the 19th century, Julius Robert Mayer, James Joule, and Hermann von Helmholtz did not have knowledge of reverse electrolysis or internal combustion engines as these technologies and concepts were developed after their time. Their work primarily focused on fundamental principles of thermodynamics, energy conservation, and related theoretical concepts. The problem that pioneering engineers face today is modern scientists' stubborn unwillingness to revisit old theoretical frameworks when confronted with new discoveries which have contradictory functions or highly coincidental properties. This is why scientific paradigms change so slowly. It isn't because it takes time to replicate an experiment by the rest of the scientific community. Rather it is, because they ignore evidence and dismiss new information that's right under their noses. Their expertise is their personal identity, and they refuse to be open minded enough to consider the possibility that there is another valid paradigm that can explain many mysteries. Instead they cling to dogmatic theories with religious fervor as if their very life depends upon it, and those old theories just lead to many more mysteries and unanswered questions. Science isn't just there to disprove theories. To truly develop, science must eventually start proving some theories correct. Unfortunately, all anyone does in physics anymore is disprove theories all day. Maybe there's a reason they cannot prove any. Maybe it's because their foundational theoretical framework is fundamentally flawed, since it was never revisited with an open mind, except by pioneering engineers of course.

@davidt1621

7 ай бұрын

@@percayaaja-153 I don't understand Hindi, Tamil, or any other Indian languages my friend. I think that's what you are using maybe. Do you speak Urdu or Farsi?

Aqui no brasil tem motos funcionando somente com água pura a muito tempo. Isso não é novidade.

UFF que maravilla sería genial adaptar las motos con ese mecanismo para empezar. Se ve genial

Wow this is so inspiring, thank you!!!

The piston rings are not made to last in water, beside that the engine sounds then same as gasoline, even if the hidrogen burns faster. Something is rotten in Denmark!

keep going!! love from Indonesia

Si esto es verdad ,este hombre es ingeniero minimo seguro. Mi enohorabuena.👍👍👍

Great ❤ be save thanks for sharing

I run my John Deere riding lawn mower on hydrogen fuel using a system very similar to this been very efficient the only thing I have added is an oil mist drip so the cylinder and piton will stay lubricated that's the only drawback on it is lubrication, but it's overcome by an oil mist drip.

using a motor to drive a generator that generates electricity to make Hydrogen (electrolysis), is completly nonsense. The efficiency is lower, the fuel consumption increases.

I can see small engine applications, but what about larger displacements? Say 300+ cubic inches (5 liter) ? This is an amazing video.

Excellent mon gars 👍🏽

SEÑORES ESO ES MUY CIERTO EN COSTA RICA POR 1:13 LOS AÑOS 70 UN MECÁNICO DE UNOS 60 AÑOS HIZO UNA DEMOSTRACIÓN ANTE LAS CÁMARAS DE TELEVISIÓN EN UN PROGRAMA EN VIVO Y LLEVÓ UN MOTOR DE CARRO Y LO PUSO A FUNCIONAR CON AGUA DURANTE LARGO RATO. DESDE ENTONCES NO SE VOLVIÓ A SABER DE ESE SEÑOR, UNOS DICEN QUE FUE DESAPARECIDO OTROS QUE LO CALLARON. PERO SI ES VERDAD QUE FUNCIONA, FUNCIONA

Por lo que se ve en otros videos de pilas de hidrógeno es sencillamente imposible que con ese nivel de producción de hidrógeno (el burbujeo que se produce) se pueda dar semejante potencia, ni siquiera para la moto en ralentí. Hay videos similares en los que da lo justo para mantener un hornillo. Yo creo que el vídeo tiene que tener truco.

AMAZING .. SO PROUD FOR YOU ❤❤❤🎉🎉🎉

dude... i didnt even think about using the Fire Arrester.. i think its also called a fire stop or something.. - MAN am i so glad i found this video.. i was trying to remember what could be used as a preventative measure to keep the lite hydrogen gas from going back to the cell

@syts3060

4 ай бұрын

Es kann mit eine in einem Rohr verpresster edel Stahlwolle hergestellt werden .

@noticiasucrania2023

3 ай бұрын

😂😂😂​@@syts3060

Essa moto vai estar a venda? Vocês fariam uma dessa sob encomend para vender?

Gracias por su tiempo amigo

Well done!!!

This is not possible. The engine can operate for a while on idle irregular cycle, not "full of gas". The engine must be carburetor. The engine is irreversibly destroyed. The video is a magic trick.

@kashmoni1085

20 сағат бұрын

You sure

Suena bien el motor, es de 4 tiempos parece... ¿Q tipo de bujia utiliza?¿Despues de modificarla necesita el filtro de aire? Funciona con hidrogeno y en vez de humo del combustible... Expulsa vapor de agua (H2O en estado gaseoso)?🤔 Agradeceria si alguien me explica xq parece un poco complicado😅

desde españa canarias me encanta ese tipo de proyecto sigan a si

Great , Thanks 👍❤️

Let's skip all the obvious lies. You say your module draws 5 amps. That's 60W. Commercially available electrolysis systems require about 50 kWh of power to produce 1 kg of H2 from 9 kg of water. Your module will be able to produce 60/50000 or 0.0012 kg = 1.2 *gram* of H2 per *hour*. Hydrogen gas releases 34 kcal per gram upon combustion in air. And you want to run a bike on that? Another even simpler debunk: 60W for an engine that needs in the order of 50kW to run?

@johnathonsandler9507

4 ай бұрын

Those are the stats for producing hydrogen. This is producing hydrogen+oxygen. It's more of a process to produce oxygen and hydrogen separately.

@erichop822

4 ай бұрын

@@johnathonsandler9507 Are you for real? I left out the oxygen part because that's a given for electrolysis. Please explain the magic you think that allows this guy to break the laws of physics?

@johnathonsandler9507

4 ай бұрын

@erichop822 it all depends on the material used and the way they are placed. I've seen situations where steel wool inside a sock then the next piece of steel wool wrapped around the sock with wires going to each steel wool for the power works also. The power used is based on the design of the metal.

@johnathonsandler9507

4 ай бұрын

@erichop822 the real question is how the hell would it produce more so the engine revs up. I get you could pump it into the air intake to save on gas but I don't understand how it could use more without upping the voltage. Seems like you would need a hydrogen fuel cell but then it would basically be all electric

@johnathonsandler9507

4 ай бұрын

Lawn mower even runs off hydrogen fuel cells and ge demonstrates everything and answers questions

Vous consommez plus d'énergie pour fabriquer de l'hydrogène que le prix qu'aurait coûté l'essence

bonjour, super video. Est t'il possible d'alimenter de la meme maniere une voiture essence en 4 cylindre?et combien de kilometres d'autonomie environ? merci.

Mil gracias Dios te bendiga 🎉❤❤❤

The future of the world of cars and motorcycles. No more pollution no gasoline, this is the ultimate solution in a world contaminated with pollutants like oil and diesel engines.

@heinzpg

4 ай бұрын

If this work we would have it already for a long time. Producing hydrogen by electrolysis is not new at all. Why doesn't this work? You can run a motor with hydrogen, but it is not possible to produce the hydrogen on board. Since the electrical power needed for electrolysis is always bigger than the power of the produced hydrogen.

Impressive how the electrolysis is working 10x faster then regular

素晴らしい✨ ただ、ガソリン噴射によって冷却されるはずのピストンが水素燃料だと熱くなり過ぎないか心配です。

What is the maximum capacity engine that can be ran at it’s standard operating power range for this setup and how longer run time can you get with that

I watchet this video and the one from arround 2 weeks ago. As it seems alot are either way hyped or totaly against it so here i try to settle some point so you can understand each other maybe. The electrolysis works yes no doubt about it. But if running a engin with it you have a different "fuel" ( in this case hydrogen ) consumtion so if you go faster it need more. To avoid running out or having a surproduction would be adding a tank. And yes it is normal you barely use direct electricity to mostly it gona empty your batterie, wich gona be recharged. Not realy using it in a direct way. It is also possible to make the electrolysis with your batterie but what is running out then ? The water first or the batterie if is the water does it mean it is produce more energie then it use ? Wich saddly is still not in human reach. You need to put more energie in then come out saddly. For the engin you can modifie an engin to run on other fuel sur. But it need some work on it for most of them exept soe older diesel wich are easier. Newer one are limited to some fuel if running on the wrong one it will just stall. Where a old one can run with less quality fuel. Modifieing a gas engin to hydrogene is not that hard ( still some work but less then a gasolin one) a gasoline would need some rework on the inside. And to the last im not against inovation but sometimes they are problems most just dont see. One of the biggest problem with hydrogen engin is the lubrification. Hydrogene is a powerfuel greas remover but a combustion engin need it or it stall and destroy itsel. So oil has to be refill offen they tryed teflon or ceramic but yeah still not any good thing found yet. So even if you modifie a engin to accept hydrogen it will have a high chance to destroy itself very fast. A hydrogen cell would be more efficiant but then instead of a combustion engin would be more a electric bike then. Hope i didnt wrote to many grammar mistakes trying my best and yes some part are very simply describte but i want that most people would understand.

@TolisOnLine

9 ай бұрын

Dude, you talk too much. Do what you see on this video & then try to improve on it. Make videos of your progress as a video reply. This is the idea here.

@user-tt4uk6rw1b

9 ай бұрын

Your right it was a long text. And i like the idea. But i wont be able to improve it the basis arent gona work. See it this way a gasolin engin and a diesel are similar and you can make work them. But make it work with another fuel need engin rework at as such it is easier to build a new one.

@TolisOnLine

9 ай бұрын

@@user-tt4uk6rw1b Very good. Now you know what to do. Gather the right people around you to make this happen. You don't need to be the one who knows all. Your vision is enough to inspire.

@MrInnovativeEnergy

9 ай бұрын

@@TolisOnLine I already have, for the past 30 years, and many other methods as well. It doesn't work as shown in this video. You need hundreds of liters per minute to run this engine at these speeds. We would all be running cars on this setup for decades if it worked.

What is the percentage of saving on gasoline fuel? Do you still need gasoline to run the bike? Or Is it 100% on hydrogen? Can you please give more specs on usage and savings ?

Superbe trouvaille, Bravo 😚🤗 ! Après ou pendant sa conquête des voitures et camions bus bateaux avions ! Il faudrait miniaturisée le prototype HYDROGEN Water-Baser ENGIN afin de limiter sa puissance pour l'adapter aux vélos et aux trottinettes à moindre coût stp ! Afin que tout le monde puisses abandonnées les énergies focilles définitivement au plus vite, De par ton geste de partage: Merci beaucoup pour nôtre Planète..

@GERARD83510

8 ай бұрын

intox ce n'est pas aussi simple que ça le putaclic de cette vidéo et des gens qui croient tout et n'importe quoi comme la vax.Pour arriver à avancer a des vitesses pareilles il faut produire beaucoup beaucoup plus d'h+ que cela garçon

water used to run vehicle engines works, it has been done here in the Philippines by a local inventor a decade ago. but of course, energy companies...

You have 2 gases in that chamber, both Oxigen and Hydrogen, elecrtolysis needs 2 electrode, one positive and one negative, indeed you have an HIGH explosive mixture in that tube, for sure it burn inside the engine, but it could explode easily in any part of the line.. i'm not sure of the amount of gas you can produce with the bike's electric implant, i think you have a little tank hided in somewhere and also if it's not the case, how have you put an explosive mixture inside an injection system originally built to work with only gasoline? keep away all the airbox it would be intresting. Bro, nice try but you lack of basic phisic's laws 😂

@ronnieyan4391

9 ай бұрын

As long as there is no spark created anywhere then it's safe

Se olvidó de desconectar la bomba de NAFTA eléctrica en la última prueba, se escucha cuando le da contacto 😂😂

VERY VERY NICE LOVE THE DESIGN ✨✨👑💜💯

How you handle Lambda values and ignition timing? If i not wrong HHO burn faster than gasoline, so i guess the ignition Angle must be lower or close to OT?🤔

Only in the process of water showed in the video, but the pure gasoline still remain in the fuel tank 😅😂

@bobbybishop5662

5 ай бұрын

Pay attention , the fuel gauge showed the fuel tank was empty.

há alguns anos atrás um homem descobriu como fazer um carro se locomover com água. e não demorou muito e ele foi morto. fica esperto.

A new neatly designed ABS Saddlebag Kit needs to be made, since the same unit can be removed & used for kitchen & generator & petrol or diesel cars or any CNG automobiles.. Backfire prevention filters are good with sand and glass layers. Good invention. :)

Quero saber que tipo de batería usas para la producción de hidrógeno y que tanto se puede recorer la moto antes que la batería se pueda descargar o dañar? Gente, recuerden que el hidrógeno explota más rápido que la gasolina, tener precaución si desean intentar y investigar más del tema Saludos!!!

Cuando mínimo debe ser 10 litros por minuto para que funcione a su 80%

So sweet man. I don’t want anything else powering my ride. Lithium is an absolute joke compared to this on board tech. This could actually make people free and sustainable around the world.

@laerteoliveira7923

3 ай бұрын

KKKKKKKKK

Comment regulez vous la demande en HHO en fonction du régime ?

Be sure to choke down the air intake, otherwise, the motor will overheat, you're getting pure oxygen along with the H2. You can find the sweet spot by taking a temperature using normal gas as fuel, make gradually test, on at warm-up, at Idle, crying down the street at 25 mph, 35, 40, 55, 65 . Mount a thermocouple on the cylinder outside, connected to a voltmeter, one you can buy at Harbour Frate, is where I got mine, comes with the TC, 20 bucks or so, also, monitor the exhaust at Idle, 20, 25, 35, 49, 55, in Gas mode. The switch to the H2 generator line. Log all this readings on paper, then you can adjust the size of the air intake to work better with the H2, supply. We had problems with over heating because we were getting to much O2, with the h2, so by restriction of the air intake, we just used Gaffer tape around the air filters, that way it's a quick adjustment, more tape , less tape, till you find the sweet spot to match the gasoline temperature range. That is what we did, and it worked fine. Disclaimer, my shared comment is for educational purposes only, Do not try this modification without a trained auto technician. I was not paid any money by anyone or any company to share my experience. Good luck, drive safely. P S, be sure to put a third filter in line to catch any water vapors or salt water from the HHO on-demand reactor. Be Safe, ware eye protection, and safety gloves. 😊

Pardal teacher. Professor pardal. No youtube tudo funciona.

esta bien la idea , pero hay que afinarlo mucho para que sea rentable empezando con cambiar el deposito combustible y poner ese de forma que sea mas practico llenar el deposito , y usar aleacion de materiales anti corrosivos por el HH , lo ideal es crear una moto desde 0 que opere con hydrogeno y hacerlo requiere una inversion grande para estudios , chile planea usar el hydrogeno en todos sus vehiculos del pais , tiene plantas donde se produce el hydrogeno verde como remplazo al combustible , pero es un proyecto que va tardar años o decadas .

Excelente video de ASMR

Hello Team Its mind blowing to travel 500kms in 1 ltr of water as fuel.Really appreciate the efforts and time to implement it. Although i have 3 thoughts in my mind 1. Is their any pressure relief valve added to the engine crankshaft cover for saftey. 2. Have you upgraded the spark plug to a non-titanium type 3. After the combustion, H2O is generated and will it mix with engine oil to cause oil leak as well as corrosion internally - any solution for that Thank you

Hace tiempo alguien terminó el paris dakar con una moto así pero no interesó a los medios de comunicación

Use "Holy Water" you'll get at least 83% boost in power.

Me encanta ver cómo queda sin tanque de gasolina ⛽ 👍

สุดยอดมากครับ

In the long run the engine will fail and destroyed because of rust and hydrogens high burn temperature cylinders and pistons needs to be covered with ceramic layer to cope with it

@ayubshaikh9156

8 ай бұрын

This hard work ,,,,,,,with ceramics in combustion chamber,……..Voila ´ ,…. Nice clean work ,,,,,,!

@CangkarmaKonang-ux6kt

7 ай бұрын

Sok tau loe cok

Where is the part of pouring water into the gas tank?

@bagdadimas

6 ай бұрын

The hydrogen cell is the two bottles mounted to the rear of the bike. It works by having the cells insulated from one another, conducting electricity through the water in which separates the hydrogen from the water. The bubbles you see produced is the hydrogen gas. You don't have to put water into the gas tank as the fuel line is connected to the secondary bottle sucking the hydrogen gas as it's made. This is called hydrogen on demand. As hydrogen isn't stored and is made as it's used, there is no potential for danger of explosion. There simply isn't enough hydrogen to be hazardous although there is enough hydrogen to run a bike engine.

You need to back engineer this with a genius architect and make it more practical for cooperation's to mass produce if its real and safe. Great vid

Possibly the coolest video I have ever seen on YT. I don't know much about science, but I can see a scene in a Mad Max 5 movie where the hero builds this to get away from the zombies with stuff all over a farm barn almost like Nowhere to run 1993 movie with JC van Dam.

It needs at least 4 liters of hydrogen per minute to work well, I don't think it works

0:53 by “HH compound starting to degrade, they really mean, “baking soda” 😊

@drewstudlino5885

2 ай бұрын

baking soda works but Potash aka potassium hydrochloride I believe it called and then even better is or the best caustic lie. The potash stuff and water you triple your hydrogen production or sometimes higher the caustic lie solution in water is like 9x amount however it's caustic and can burn your skin ect.

What is the rate of consumption vs. generation? Did it generate faster than it uses even at highway speeds?

エンジンオイルは乳化しますか？ 内燃機関での水素利用では、エンジン内の水蒸気とオイルが混ざって乳化してしまうと思いました。

and what about the lubrification of the gaz in cylindre ???

Vc e muito inteligente valeu

Неужели понемногу разрешают людям пользоваться, этой технологией, спасибо💪👍👏

Lo encontraron muerto por suicidio con 40 disparos por la espalda atado y debajo de un lago.

Pray for this people, they will need protection