Rocker Lockers Install 2014 Twin Cam FLHTCU. Rocker Locker Kit works very well.
Жүктеу.....
Пікірлер: 21
@jimirox19282 ай бұрын
I Installed Rocker Lockers on my Softail a few years. It used to sound like two skeletons screwing on a tin roof but now it's nice and quiet.
@stanwerner7484 Жыл бұрын
Nice job---but just as an FYI---you don't need to completely remove the rocker assy to install the "Lockers", just make sure there is "No load" on the Rockers and do one bolt at a time.--just an fYi.
@fishandgameman Жыл бұрын
Whatever you do, make sure the blind holes for the breather bolts are void of any oil. Swab the hole with a Q-Tip or blow it out with shop air. The hydraulic pressure from any remaining oil will blow out the underside of the head before you even get near the torque specs. Those breathers can be counter intuitive during assembly and it’s easy to get them wrong. Don’t ask me how I know. 😆 If you get confused, check out the video, “My Harley Blows” (It’s dipstick). Nice video! 👍
@goodboyringo971610 ай бұрын
Rocker locker didn't stop my Twin Ticker !
@rrmorris673 жыл бұрын
the 2005 Road King 88 I recently obtained is so loud on the front cylinder i can't believe it. I sure hope this fixes it. I've had a Yamaha V Twin for 25 years. I'm not prepared for Harley quirks.
@Richard58732 жыл бұрын
At 4:51 I do not have to put piston at top dead center before tightening base plate bolts down ? Just like when adjusting push rods. I'm doing thing project this weekend. Great video Thanks for Great information
@A70072 жыл бұрын
May i ask if the rocker locker have a life time ?? And for how long would last before i need to change it
@bm77603 жыл бұрын
I've a set on order. Hoping it cures the top-end rattle that's driving me nuts. Then I'll sell this POS and buy a decent bike.
@romesyoutubechannel5356
Жыл бұрын
I'm with you bro... and that's exactly what I'm going to do.
@efakter1 Жыл бұрын
How did you get that bushing out? Because that just happened to me
@smrtrbl86 Жыл бұрын
At 4:05. What do you mean radius on the pin?
@johnjohnson28556 ай бұрын
What years are these for
@matt88632 жыл бұрын
3:00 Is that camera trickery or are those bolts reverse thread??
@Christopher-cd3pc
Жыл бұрын
Must have been mirrored image or something
@smrtrbl86
Жыл бұрын
He used his cell phone is forward facing camera mode. Makes it all look reverse. You can tell by how he tightens the bolts reverse instead of clockwise
@dulian083 жыл бұрын
There is a better way !! You drill a hole on the bottom square to the pin and tap it then bolt down a Allen stopper to the pin !!! They will never move again.!!
@simplex4297
2 жыл бұрын
Yep ,the better way is called the Tim Stone method right here on U Tube.
@PkwyDrive134 жыл бұрын
Please tell me I don't have to drain the oil or anything to do this? I literally just did an amsoil 3 hole oil change yesterday..
@Rick-Williams59
4 жыл бұрын
Nope, you don't have to drain the oil, I've used them in the last 2 Harleys I've owned.
@jimscycleandautotn8508
3 жыл бұрын
Um.... Nah just turn the bike upside down and all the oil will float to the top
@fagen22223 ай бұрын
if you got a longer bolt could you not press it in in situation or am i worn
Пікірлер: 21
I Installed Rocker Lockers on my Softail a few years. It used to sound like two skeletons screwing on a tin roof but now it's nice and quiet.
Nice job---but just as an FYI---you don't need to completely remove the rocker assy to install the "Lockers", just make sure there is "No load" on the Rockers and do one bolt at a time.--just an fYi.
Whatever you do, make sure the blind holes for the breather bolts are void of any oil. Swab the hole with a Q-Tip or blow it out with shop air. The hydraulic pressure from any remaining oil will blow out the underside of the head before you even get near the torque specs. Those breathers can be counter intuitive during assembly and it’s easy to get them wrong. Don’t ask me how I know. 😆 If you get confused, check out the video, “My Harley Blows” (It’s dipstick). Nice video! 👍
Rocker locker didn't stop my Twin Ticker !
the 2005 Road King 88 I recently obtained is so loud on the front cylinder i can't believe it. I sure hope this fixes it. I've had a Yamaha V Twin for 25 years. I'm not prepared for Harley quirks.
At 4:51 I do not have to put piston at top dead center before tightening base plate bolts down ? Just like when adjusting push rods. I'm doing thing project this weekend. Great video Thanks for Great information
May i ask if the rocker locker have a life time ?? And for how long would last before i need to change it
I've a set on order. Hoping it cures the top-end rattle that's driving me nuts. Then I'll sell this POS and buy a decent bike.
@romesyoutubechannel5356
Жыл бұрын
I'm with you bro... and that's exactly what I'm going to do.
How did you get that bushing out? Because that just happened to me
At 4:05. What do you mean radius on the pin?
What years are these for
3:00 Is that camera trickery or are those bolts reverse thread??
@Christopher-cd3pc
Жыл бұрын
Must have been mirrored image or something
@smrtrbl86
Жыл бұрын
He used his cell phone is forward facing camera mode. Makes it all look reverse. You can tell by how he tightens the bolts reverse instead of clockwise
There is a better way !! You drill a hole on the bottom square to the pin and tap it then bolt down a Allen stopper to the pin !!! They will never move again.!!
@simplex4297
2 жыл бұрын
Yep ,the better way is called the Tim Stone method right here on U Tube.
Please tell me I don't have to drain the oil or anything to do this? I literally just did an amsoil 3 hole oil change yesterday..
@Rick-Williams59
4 жыл бұрын
Nope, you don't have to drain the oil, I've used them in the last 2 Harleys I've owned.
@jimscycleandautotn8508
3 жыл бұрын
Um.... Nah just turn the bike upside down and all the oil will float to the top
if you got a longer bolt could you not press it in in situation or am i worn