hey sam, did u not put any sealer on the corners of the head, just were the seams are? i was under the impression even with a new gasket this had to be done, or it will leak again bud

@sampaddyprojectz

Жыл бұрын

Thanks for the heads up! I’ve pinned the comment to the top so others can know this 🙏🏻

@daz918

Жыл бұрын

@sampaddy, nice 1 bud, just the 4 corners need a little, im sure if u watch your video back, u will see some of the factory sealer, kinda orange in colour i think, i did the same as urself many years ago, but no sealer, and it leaked after a few days, dab of honda bond, all good😄👍

@XRayXI

Жыл бұрын

@@daz918 Combined knowledge sir. Great respect that you also want to help others. 💪

@daz918

Жыл бұрын

@xrayxl all us honda lovers have to share hints and tips in the community, im a cl9 owner, learnt a lot from these kinda how to videos, from reseting vsa/abs, to timing chains and tensioners, to some of the easier things, cam covers, valve lash etc, its a great group to be part of, 😄🏴󠁧󠁢󠁳󠁣󠁴󠁿👍

@XRayXI

Жыл бұрын

@@daz918 I can't agree more with you, absolutely 100%. And the world opens up, if you search for FN2 videos. Amazing knowledge share based information. Actually, you don't know where to start haha. Dynodaze Honda videos is a good start and what can be modded. Not to advetrtisement for them, but how many lovely people there are in their community too. Just top notch and honest. Just like you are 🙂

Wish i had watched this yesterday before i did mine! Great video!

sick video lad!

Yes Sam great video bud easy to watch content my man keep it up… looks 100% better..👍🏻🏎👌🏻🤛🏻

Good job 👍

Nice vid man, just bought an FN2 so will subscribe!

@sampaddyprojectz

Жыл бұрын

Cheers! Plenty more mod vids to come 🤝🏻

Hey Sam Good job it improves the look 100%. I would like to do mine but not really competent enough. When are you free lol

@sampaddyprojectz

Жыл бұрын

Hahaa nah you’ll be fine mate, scariest bit is worrying about it! Actually doing it isn’t to bad 👍🏻

Hey dude great vid, what spray can did you use for gold and was it high temp also were from? Thanks

Great video! That looks so good. I just wonder if you could have done the valve clearance with it too? You had it off and could check for specs. Anyway, alway snice to see DIY videos about the FN2. Got mine last month of the 10th. Got a nice list of a to do list, lol. Btw, check @daz question below. Even though you used a thin layer as a sealer. Just keep an eye on it ;-) (sure you do!)

@sampaddyprojectz

Жыл бұрын

Cheers! I should have done the valve clearances I even have a feeler gauge 😅 I’ll pin daz’s comment so other people can be aware of this, I may have it off again when I do the chain so noted!

@XRayXI

Жыл бұрын

@@sampaddyprojectz Looking forward to your next videos sir and thank you so much! 👏

Man like Sam paddy 🔥🔥🔥🔥 that is looking sexcy fam

@sampaddyprojectz

Жыл бұрын

My broo 🙏🏻 wanna see you do your engine bay next 🏎💥

@damiowolana5432

Жыл бұрын

I’m ready message me when you free this month

Hi sam the rocker circle rubber seals how far in after banging do they go. Like is it all the way down? Mine stuck half way after hitting them in. Please advice ASAP thanks?????

@sampaddyprojectz

Жыл бұрын

Should be seated well enough after a few taps with a rubber mallet, have a look from the top of the rocker cover, as long as there sitting evenly when you tighten it down they will go into place 👍🏻

Great video dude! What paint did you use?

@sampaddyprojectz

Жыл бұрын

Thanks! Gold caliper paint link - www.ebay.co.uk/itm/162685433574?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=4VMhS1_vS6K&sssrc=2349624&ssuid=zCg5FDsJRVa&var=&widget_ver=artemis&media=COPY

Mate amazing video Appsalutally brilliant 👏 thanks mate brilliant direction on how to do it you've made it so easy Can I ask you a question have you done the damper bypass as there's some videos on here the have done it but they don't do things step by step as you do mate they skip alot of things ! I want to do mine Are you going to do it or have you done it thanks mate Gerry 👍

@sampaddyprojectz

8 ай бұрын

Nice one Gerry! I’ll defo look into that, I’m back on the tools and the camera so happy to look into it and make a video if I can brother 🫡

Hi pal Do you think that your car needs valve clearence at this milages? Or not nessesary yet? Mines got 169k and im thinking to do it

@sampaddyprojectz

6 ай бұрын

Yeah deffo do them at that milage bro 🫡