Amazing work with Rhino without Grasshopper. Great process is demonstrated.

Thanks to this video I learned what record history does :D

@yakupkaraer

10 ай бұрын

hahaha evet, güzel bir özellik aslında 😊

really great video !! thanx a lot for helping me out

@yakupkaraer

11 ай бұрын

I really appreciate your kind words. Thank you.🙌😊

Nice Vid !

@yakupkaraer

2 жыл бұрын

Thank you 😊

Kindly add subtitles about the steps and commands. It'll be easier to understand the workflow.

@yakupkaraer

Жыл бұрын

Thank you for your comment. Subtitles will be added. 😊

@alalalus7692

8 ай бұрын

Still no subtitles@@yakupkaraer

Thanks you for the great tut. I was wondering if you can show us how to lay them flat ( Nesting ) later on and maybe numbering the pieces to get them ready for CNC production.

@DJ-ll2ye

5 ай бұрын

each section needs to be aligned to 1 plane. if each part has a lot of draft, make sure the side with the most surface area sits on the plane so you can run a ball nose contour path around it. Align a face of the body to the plane you want so it sits flat

@yakupkaraer

4 ай бұрын

Check out the video where I prepare the cutting list from grasshopper.🙌🙌 Link: kzread.info/dash/bejne/X22IqquehJPAdLA.html&ab_channel=YakupKaraer

@yosofya

4 ай бұрын

Appreciate your Response and Support. I have watched it, looks exactly what i was looking for. I hope your next videos will be with voice recording and more explanations. that would be awesome. thanks @@yakupkaraer

thank you ! but how did you close the right and left with the surface after extruding the lines?

@yakupkaraer

Жыл бұрын

With the cap command. I did it at 6:07. Did I understand the problem correctly?

@shamimvahdat6232

11 ай бұрын

Can you explain more please?

Hello! At 3:43 when I extruded the curves, the surfaces haven't created, just the edges are looking. Did I wrong thing?

@yakupkaraer

Жыл бұрын

After entering the "ExtrudeCrv" command, the "Solid" option in the command bar above should be set to "Yes." 😊🙏🏻

selam, bu yanda loft ayarlarını düzenlediğiniz seçeneklerin çıktığı bilgisayar simgeli arayüz bende bulunmuyor? atrı bir eklenti mi eklemeliyim? nasıl açabilirim? teşekkürler.

@yakupkaraer

2 жыл бұрын

O kısıma sağ tıklayın. Display diye çıkacaktır. Display'i aktif edin olacaktır. Sorunuzu doğru anladıysam..😊

@eliftk4201

2 жыл бұрын

@@yakupkaraer teşekkürler :)

Hi, how do you select the isocurves and move them then the loft changes automatically ?

@yakupkaraer

2 жыл бұрын

Activate record history before loft. If you look at 2.02 minutes. 😊Then click surface. Then click f10. 👍

@MR.credent1al

2 жыл бұрын

@@yakupkaraer It worked

@casaproductoramejia

9 ай бұрын

​@@yakupkaraer THANK U! I had the same question

@eliir5720

7 ай бұрын

thank you same question @@yakupkaraer

I can't understand 2:24 min point After clicking on curve u have drag is front side & after that what u did to make a curve bench plz tell me..

@yakupkaraer

Жыл бұрын

Open Record History. Select the lines and enter the loft command. The lines will slide. 🙏🏻🙏🏻

@marabelsito4270

3 ай бұрын

can u explain that part in a different way? it still doesn't work for me@@yakupkaraer

@yakupkaraer

3 ай бұрын

@@marabelsito4270 Keep only the lines. Enable the Record History option below. Select all the lines. Enter the 'Loft' command. After changing the positions of the lines, the object's position should change instantly. -- Did it work for you? -- 🙌

great video. Now , if we were to make this. How would we get the sections for each contour?

@yakupkaraer

Жыл бұрын

The easy way is to do it from Grasshopper. But if you don't know Grasshopper, you need to extract from Rhino one by one.🙏🏻🙏🏻

@yakupkaraer

Жыл бұрын

Nice question 😊😊

@susurrosjoe6817

Жыл бұрын

​@@yakupkaraerHow It would be on Grasshopper? I'm very interested cause maybe It could apply to pollar arrays too. Thx very much.

@yakupkaraer

4 ай бұрын

Check out the video where I prepare the cutting list from grasshopper.🙌🙌 Link: kzread.info/dash/bejne/X22IqquehJPAdLA.html&ab_channel=YakupKaraer

Thank you so much ❤. But how i can export cutting template of this kind of shapes ?

@yakupkaraer

5 ай бұрын

There are fabrication videos related to Grasshopper available on KZread. I'll also have a project soon. But unfortunately, it requires using Grasshopper. 🙌

Nice. How much cost the Software?

@yakupkaraer

4 ай бұрын

You can look at this link. Link: www.rhino3d.com/en/sales/europe/Turkey/all/

bRAVO .. ,.

JK,

Bir de anlatım yapsaydın daha güzel olurdu. Teşekkürler.

@yakupkaraer

2 ай бұрын

Global'e izlenmesi için anlatım yapmıyorum. Biraz Rhino bilgisi olanlar için aslında videolar. Teşekkürler.

@ahmetnurikok5674

2 ай бұрын

@@yakupkaraer öğrenmeye devam o zaman. Teşekkür ederim.

Good idea. Nicely done… never the less The worst music ever

@yakupkaraer

11 ай бұрын

Thank you for your comment. The music is subject to copyright issues, which is why finding good royalty-free music can be difficult. 🙏🏻🙏🏻

А чё так медленно всё делал? Надо было бы побыстрее, чтоб ещё больше непонятно было. Мне же так хочется постоянно перематывать назад и смотреть со скоростью 0.5

@yakupkaraer

9 ай бұрын

Thank you for your comment. I'll make a faster version of it in a video for you as soon as possible.🙏🏻🙏🏻

@rooferspb

9 ай бұрын

@@yakupkaraer thanks