Amazing power of resonance: the same place of circuit turns red both thick copper wire requiring dozens of amperes to glow, both thin tungsten wire, requiring dozens of volts to glow.

I like this very much. I was going to bu one, but i had the parts to build. Only experimented with it for 2 hours. I tried 0.40uf to 1uf but little change in performance. I parallel IGBT's for use of 4, again little difference. Next i will try different coils but circuit seems tuned well as is. Used 13 volt motorcycle Lithium battery.

this is the most simple ZVS oscilator i've ever seen, it works but it seems that the standby curent is high, perhaps you can create another version with lower standby current, it will be awesome

You do some of the best builds of skeleton circuits on the planet, literally. Well done!! Truly interesting circuit with no diodes, resistors or inductors (other than all the copper). I look forward to your next video!! Thanks!

@ZAFERYILDIZ52

2 ай бұрын

Many channels will use this design closely :) Thank you for your comments and support.

@m.hasanyavari.s4083

Ай бұрын

دمت گرم❤

@alimahmoodi8322

Ай бұрын

سلام ، مدار های الکترونیکی که شما ارائه می‌دهید، هم خلاقانه است ،هم ساده و قابل فهم و هم کاربردی است .احسنت به این خلاقیت شما .متشکر .❤❤❤

@BayuRahmanan

18 күн бұрын

​​@@ZAFERYILDIZ52Can this concept also be applied to the induction door lock method? Thanks

شكرا لك استاذنا المحترم

В конце видео один транзистор сгорел. Ток был 2.7 ампер, потом подскочил до 9 ампер. Полевые и IGBT транзисторы имеют ограничения по напряжению на затворах. Не более 20 вольт.

@MsAndru79

2 ай бұрын

стабилитроны в затворы не ставил и транзюки на радиаторах

@ZAFERYILDIZ52

2 ай бұрын

Причина горения в том, что провод катушки был намотан слишком тонко и нагрузка находилась на одной стороне.

@mmikrik

2 ай бұрын

@@MsAndru79 зачем так, контента не будет. Народу нравится мощщ..гром и молнии)

@mmikrik

2 ай бұрын

@@ZAFERYILDIZ52 нет, как раз причина в сгоревшем транзисторе. он сгорел в тот момент когда ток подскочил очень резко! смотри внимательнее

@donramonramirez5141

Ай бұрын

La tensión de puerta del IGBT, no debe superar los 12 Vcc, en el peor de los casos ... Y encima, puso a trabajar los IGBT SIN RADIADOR, sin el soporte correcto, en alta frecuencia y potencia ... No podía pasar otra cosa que TERMINAR ROTO ... Un trabajo de mierda ... 🤦🤦🤦

I love watching your videos. I was particularly intrigued to see how you would create an induction heater without a coil... until 2:44 when you started to wind a coil!! 😂😂

@ZAFERYILDIZ52

2 ай бұрын

the aforementioned babon indicator

Kkolay gelsin zafer bey, verdiğiniz bilgilerden faydalanıyoruz teşekürler.

Спасибо Вам за ваши видео! Очень интересно и приятно смотреть ваши разработки.

@ZAFERYILDIZ52

2 ай бұрын

Благодарю вас от всего сердца за поддержку и искренний комментарий.

Finally I got new knowledge from this video

J'ai essayé le montage, ça fonctionne bien, pas oublier des refroidisseurs sur les transistors, bravo !

സൂപ്പർ ആയിട്ടുണ്ട്. നന്ദി സാർ❤

@ZAFERYILDIZ52

2 ай бұрын

നിങ്ങളുടെ അഭിപ്രായത്തിനും പിന്തുണയ്ക്കും നന്ദി.

‏‪3:42‬‏ رائع برافوا عليك ❤❤❤❤❤❤❤❤❤

Top demais parabéns 👏👏👏👏

It's possible for testing purposes, but definitely need a heatsink for IGBT .

Teşekkürler Zafer bey

Ive always waiting for new video definitely im new at electronics but i am a ac tech when im out of work i xopy all your piece more power from Philippines here I copy some of ur piece and im keep improving my skil...

@ZAFERYILDIZ52

2 ай бұрын

love to the philippines

GREAT VIDEO!!! On a standard induction heater, the peak output is about three times as much as the input, however, on the IGBT induction heater it is about three times LESS. Is this correct?? THANKS MUCH!!!

Good work Thanks for sharing

@ZAFERYILDIZ52

2 ай бұрын

Thanks for the nice comment and support.

хороший пример того для чего используются наборы пластин в трансформаторе, чтобы не пораждать токи фуко и не нагревать сердечник)))

Zafer hocam datasheete baktım bundan inverter yapabilirmiyiz? Pc 300W diyor bize yeter ufak bir şeyler çalıştırmak için. Yalnız bir sorum var trafo kullan madan yapabilir miyiz?

Bence nobel ödülünü hakediyor gercekten devrim niteliğinde bir buluş tebrik ediyorum

سيد ظافر شكرا لك هل يمكن صنع نفس التصميم بقدرة اعلى باستخدام igbt كبير جدا

Would this configuration work with an igbt like a Mitsubishi qm100dy-h igbt (or equivalent)module? 600v 100a would make for quite an inductive heater.

@RAM84655

Ай бұрын

هل تعمل جيدا برأيك

Very good!

Any one no of a good temperature control for that circuit

Гениально👍☝️

VEREY NICE.THANK YOU

Very nice information Great work for you Sir ji 🎉 bahut bahut shukriya Bhai Ji

@ZAFERYILDIZ52

2 ай бұрын

Thank you for your comment and support.

@1964.0

Ай бұрын

​@@ZAFERYILDIZ52какое сечение провода катушки? Заранее спасибо!

Nice Video and excellent wire forming skills! Every time I see people useing "Lead-Free" solder, I feel sorry for them having to use it instead of 60/40 or 63/37 eutectic solders.

@electrocat9

Ай бұрын

How do you know it is lead free?

@joeteejoetee

Ай бұрын

Because I did not want to say that the solder connections are/look awful, I blamed that on lead free solder instead of soldering skill. I have been Soldering for over 50 years, and I have used ROHS Solders before, and they are no where near is good as traditional solders still are. You should try it sometime! @@electrocat9

7:42 Not only the lamp lit up, the coil too 🙂

مشاء الله عليك مهندسنا العزيز بارك الله فيك تحية طيبة

@srrincekara9499

2 ай бұрын

🤲🤲🤲

@ZAFERYILDIZ52

2 ай бұрын

شكرا على التعليق الرائع والدعم آمين

Would this build work to heat a bolt (stuck) that fits inside the coil ? Ive been looking for one of the tools but the costs are too much for me (not a mechanic). I watched another video where they used an old twisty style light bulb and built one.

Eline saglik ustam bir de bunu kaynak makinasi ile yapabilir misin

Dose it work well with 220 volt DC? Thank you

Svaka vam čast gospodine, sve ste rekli .lp

bermanfaat banget boz..

I have subscribed to your channel. Tell me how much temperature can I gain with this heater so that I can melt some metals that can melt only at high temperatures. Thank you very much.

teşekkürler abi .

Sahi said bro

Is it possible to make induction heater using bjt?

All that stuff is basically a DC to AC converter that I assume has a pretty high frequency? That frequency would come from the value of the capacitor?

elinize sağlık ustam

@ZAFERYILDIZ52

2 ай бұрын

teşekkürler kardeşim

Good work I wish you all the best Can you make with

Nüve ile yönlendirme yapilabilrmi ?

❤❤❤ eline sağlık ustam

@ZAFERYILDIZ52

2 ай бұрын

çok teşekkür ederim kardeşim

Super Perfekt

@ZAFERYILDIZ52

2 ай бұрын

thx my friend

ماهي اقوى دائرة يمكننا صنعها لصهر المعادن

Bagaimana rara buat input 220 volt om?

bravo

Does Any inductor has a very high voltage or current across the copper coil,is it dangerous??

Can you increase the voltage to 36-48VDC to maximize the wattage?

Nice!

PEKİ HOCAM bu ebatlarda isitici max kaç mm kaınlıkları ısıtabilir ? mesela bi 5 mm ısıtabilirmi bıcak yapımında kullanmak için işe yararmı

@ZAFERYILDIZ52

2 ай бұрын

IGBT sogutucu ekleyin ve 24v 10 amperle besleyin 10 mm dahi ısıtmaya yeter bu arada bobin telini daha kalın sarın 2,5 mm telden

@1dayinthefuture101

Ай бұрын

Herhangibir ıgbt olurmu sizin kullandığınızı bulamadım intetnette

Great.

The circuit looks like a transistor based multivibrator. The IGBT needs to be on heat sinks since circuit current is nearly 6.8 Amps. Heating a blade is only for demonstration. If one wants to heat bigger objects the circuit should be scaled up with a good power supply , cooling fan etc. Good work.

Very nice job 👍 can you make this work without the centre tap coil ?

Cool! 😎 🔥

Super ❤

@ZAFERYILDIZ52

2 ай бұрын

thx my friend

Merhaba, + uç neden bobinin ortasından veriliyor? Başka bir yöntemi yok mu?

Title: no mosfet **mosfets**

@Ulai-ov2zh

Ай бұрын

WHAT THE?! NO NOTHING?!?!!

Bunun biraz büyüğünü yapsak evi ısıtırmı fatura çok gelirmi

please add a variable to adjust power of induction

What size is the magnet wire for the coil? Do I need heatsinks for the transistors?

@electrocat9

Ай бұрын

What is magnet wire?

@GvIn2it

Ай бұрын

@@electrocat9 en.wikipedia.org › wiki › Magnet_wire

Good 💯

@ZAFERYILDIZ52

2 ай бұрын

thx my friend

Bravo Hocam 👏

@ZAFERYILDIZ52

2 ай бұрын

teşekkürler kardeşim

Merhaba Dhafer kardeşim. Bu yöntem IGBT'yi aşırı ısıtmıyor mu? Çabuk yanıyor mu, yanmıyor mu? Lütfen cevap verin. Teşekkür ederim.

@ZAFERYILDIZ52

2 ай бұрын

IGBT mosfetten daha dayanıklıdır ve farkındaysanız sogutucu koymadım ama uzun süre kullanım için sogutucu ekleyin tabiki

Good 👍👍👍🙏

Wow, flux used on a video like this. Congratulations! Would love to know how hot the transistors are running. I know the coil is crazy hot as that is normal and limits the duty cycle of induction heaters if you don't use tubing with cooling liquid.

For a 72 watt heater use for few seconds at a time that will work like that

Daha güçlü indüksiyon için bir bilgi alabilirmiyiz.

Where do I get a schematic

How long do you think those IGBTs are going to last with no heat sink?

Единственное несовпадение, которое я не могу объяснить, это когда осциллоскоп показывает без нагрузки 100 кГц, а под нагрузкой 180 кГц. При этом синусоида расширяется. хотя частота увеличивается.

@LeandroAndrus-fn4pt

Ай бұрын

Частота была 181 без «нагрузки»(повышения индукции) и 160 с дополнительной индукцией

Nice

Typically tank circuits will fry the transistors if you slowly bring the power up. [They won't start oscillating] They require instant voltage application to it ???

Mosfetli versiyonlardaki gibi şok bobini taksak iki çıkışlı olarak çalışır mı?

@ZAFERYILDIZ52

2 ай бұрын

Çalışır

How do I make one for 2000 watts

Good inovesan

I like bravo

HDD slow thaan but data recovery ku best ahh irukkum ji SSD damage aakiduchu apdinaa data recovery rombave kastam illa pannave mudiyaamalum pogalaam ji

So I’ve read a lot of the skeptical comments on this build so I thought I’d give it a try. I found the igbts, caps and got it built.The circuit functions exactly as shown in the video and circuit diagram and it 100% works as advertised. Really, very cool. Thanks again for this build!!

De todo lo que lleva es una resistencia calentadora

I don't find 0,27 uF ... Can I replace it with more uF or less? Thank you

@SoundsLegit71

Ай бұрын

I tried 0,40-0,80 uf and that worked about the same.

Интересно!👍

🎉 super

@ZAFERYILDIZ52

2 ай бұрын

thx my friend

Emeğine sağlık Trabzon Okan Elk'ten Selam

@ZAFERYILDIZ52

2 ай бұрын

Trabzona selam kardeşim

I made this for my bird house heater

Bikin yg bisa di jual di pasaran mas ?

Saya ingin tau kumparan yang lebih banyak utk menyalakan lampu 220v atau pake kumparan sekunder yang dimasukan ke dalam kumparan primer induksi tanpa ferit

@paruguh3907

2 ай бұрын

Tes tegangan pake dioda cepat diantara kumparan

@ZAFERYILDIZ52

2 ай бұрын

👌

Why did the coil start glowing as well?

Maşallah kanalın dahada gelişiyor kardeşim. Allah yolunu açık etsin hayırlı Ramazanlar herkese.

Ustam o güzel sesini özledik ya eskiden her videonda konusurdun

@ZAFERYILDIZ52

2 ай бұрын

👉❤👈

Can you modify this circuit to use a flat coil please?

@ZAFERYILDIZ52

2 ай бұрын

It's not a flat coil, bro, but you can wrap it on a core.

Excellent ❤❤❤

@ZAFERYILDIZ52

2 ай бұрын

thx my friend

I don’t understand the lightbulb. You get current drawn when you have resistance. Like a light bulb for instance. Powering the light bulb would be more useful with the minleaf variable power supply. Otherwise I was able to follow along to your build on a different take of induction coil heater. 😅

Так надо попробовать на МОП-транзисторах. Напряжения тут низкие!

Usta bunu biraz daha güçlü yapmak istersek voltajı arttirsak yeterli olur mu

@ZAFERYILDIZ52

2 ай бұрын

daha güçlü IGBT kullanmak daha iyi olacaktır

Как понять название , без транзисторов ?

İndüksiyon bobininin sarım çapını büyütebilir miyiz?

@b4dmblm705

2 ай бұрын

I'm glad you are asking cause I was wondering the same thing.

@ZAFERYILDIZ52

2 ай бұрын

evet cm kadar çıkabilirsiniz ancak sonuç için giriş gerilimi 30 volt olmalı ve sogutucu ekleyin