very nice job. but four things concern me, one the water that came out of the tank, in order for me to use that tank I would preform a hydraulic test in order to validate the structural integrity of the tank. Two I would be cautious of using the old pressure switch, it might work for a bit but would fail down the road, I would end up replacing it with a new one. Three I would never paint the air pipes with the fins coming off the compressor, due that what helps cols the hot air coming off the compressor. And Four I would replace the quick connect couplers with newer ones so I can us them with any newer air hose and tools.

@worawutmonglampang3690

2 жыл бұрын

llllll

@alexanderzawydiwski9534

Жыл бұрын

I agree is this thing just be a big bomb

I admire the hard work but it seems you don't care about some details and I must agree with some comments about them. Still a good job: you saved an old air compressor, so many years still to live. Thanks for the video.

@Kofolix

5 жыл бұрын

I rather call that a WASTE of TIME, him doing things he had done and us all watching it...................... lets use real names for real things otherwise we all end up as that poor compressor - artificiall

Rusty pressure tank ... what could go wrong?

@JosephArata

5 жыл бұрын

If you think that was rusty, you haven't seen rusty oilfield gas pipeline that hasn't been maintained properly.

@acespark1

5 жыл бұрын

you don`t worry the explosion will be in the next village

@bratanbaraban

5 жыл бұрын

@@JosephArata зз$бббббббббббббббббжзббббзз$з$бббббббббббббббз$бббббббббббббббббз$бббжзбжхбббббббббббббббббббббббббб$з ббббббббббббббббббббз$бзбзбзбббббббббббббббббббб$з бзззз$ббббббббббзбжббббббзбзбзббзбзбзбзбззббзббббббббббббббббббббзбзббзбззббббббббббббббббзббззззз$збз№ззззбззбзббббзбзз$бббббббббббббббззззхззззззззз$ббббббббббббббббббббззбзбзз$збзбззббббзхззбзбззбббббббббббзбзббббббзбзбзззбзхз$ззззбззбббббббббббббббзззхзззз

@kenbar4761

5 жыл бұрын

Nothing. He released the pressure.

@Nando_

4 жыл бұрын

you know it gethers water and rust from inside too, right? please check your life insurance

Já fiz esse serviço em um compressor de ar, é um bom aprendizado de como tudo funciona e seus ajustes. Parabéns!

When he sprayed water into the crankcase I had to cry.😭

they have not been opened and checked: engine, valves, ball bearings and fittings. most importantly, no air leaks have been checked from the tank and at the beginning of the video the water is rust-colored, it is not a good sign, probably the inside is worse than the outside. advice on painting: do not paint the cylinder dissipation slats otherwise the heat will not be disposed and there will be a risk of breakage due to overheating.

@mrdis58

5 жыл бұрын

It's clear he doesn't have a clue what he's doing.

@ShainAndrews

5 жыл бұрын

do not paint the cylinder dissipation slats otherwise the heat will not be disposed and there will be a risk of breakage due to overheating. That is inaccurate. Heat dissipation is the same painted or not. They are painted from the manufactures.

@giampierodipietrantonio2847

5 жыл бұрын

@@ShainAndrews the manufacturer's painting is specific to have a high heat exchange, the one used in the video is a normal discount paint shop. there are different types of paints, some tend to block the temperature (surfaces treated for thermal insulation) others resistant over 600 degrees (car brakes, turbo covers).

@ShainAndrews

5 жыл бұрын

@@giampierodipietrantonio2847 You bumped your head if you think that budget compressor came from the factory with some special heat conductive paint and anything he applied is going to block that thermal exchange. Paints you mentioned have nothing to do with thermal conductivity.

Anyone who puts hate in these videos I want you to think about how you would feel if you were the person getting the hate. You "adults" need to grow the hell up and stop sending so much hate and start commenting nice things. I guarentee that most of you who comment hate can't do anything in this video or any of the other restoration videos on this channel. I seriously hope that you people learn that nobody cares about all the hate and that you just need to treat others as you would treat yourself. Excellent work. Keep it up. I support you all the way on your restorations!😁

@stevenakn1

5 жыл бұрын

Nice job 👍

Watching that painting hurts so bad 😂

@TobiasHinz1992

5 жыл бұрын

It´s a tool, it doesn´t have to be super shiny.

@royk007

5 жыл бұрын

@@TobiasHinz1992 nope just have to be perfect ;)

@OGKILLa9365

5 жыл бұрын

its a old ass compressor not a car.

@2stepsaway820

5 жыл бұрын

Ikr it was a bit slap dash

@ricotheque

5 жыл бұрын

And watching the crappy water running on the floor...😸

Зачем разбирал непонятно, мог бы просто всё краской облить, тоже самое бы вышло!! И красить надо было в розовый, мы хоть поржали бы :D

@user-accept

5 жыл бұрын

Это называется. ,, Ревизия,, .

@killr69

4 жыл бұрын

@@user-accept А видео называется реставрация-зачем наебывать?хайпа ради

... no pressure test, no new ball bearings, did not open motor, did not check valves... ... it was not restoration, it was a cleaning and paiting job. ... a lot to do ...

@iKaktys

5 жыл бұрын

and look like fake olded

@imperialpresence3331

5 жыл бұрын

cleaning and painting is how american tools stay in american shops...there is a diy base that doesn't have access to warehoused and high tech machines...some have to shop out pawnshops and harbor freight...my first table saw was a cast off

@bigornafilmes

5 жыл бұрын

@@therestoration2r878 , thanks for your initiative recovering an old compressor. Good luck ...!

@AlaskanPotHead

5 жыл бұрын

@@therestoration2r878 If you don't do restorations, then the name of your channel is very misleading.

@isolophilia12

5 жыл бұрын

Grow up

Como dice Marcos Marques, podría haber sido mejor, pero considero que con la limitación de recursos fue bastante buena. Felicitaciones!!

I'm a car guy and I love taking stuff apart I take in lawn mower engines apart before and I just absolutely love this video

Ржавый фигня) пускового конденсатора нет, цилиндры с ржавчиной) ресивер надо бы на давление проверить после такого простоя)

Такое ощущение,что компрессор специально ободрали от краски и бросили в воду, чтобы потом типа отреставрировать

@user-tx5ej3fv5d

5 жыл бұрын

iceman86 я тоже так подумал))))

@alknis

5 жыл бұрын

Оригинальный цвет был лучше. Да и не стоило его обдирать. Просто внутри всё перебрать и этого хватило бы.

@DRAGUNOFFWORKSHOP

4 жыл бұрын

так оно и есть. Среди блогеров такого формата это известный прием. Как говорится ничего личного, это бизнес...

Excelente!!! Gracias sos una inspiración para empezar a restaurar mi compresor.

Very good restoration video. I prefer these slightly longer restorations of complex machinery.

Channel should be called " 5 year maintenance" and not restoration as it fell quite short of restoration. Not enough in depth work went into this project. I can appreciate the effort to make this a better working machine but it still falls short of a FULL RESTORATION. Much more attention to detail needed to actually call it a RESTORATION.

Painful to watch...

@cereal_qilla

5 жыл бұрын

Why

@GGigabiteM

4 жыл бұрын

@@cereal_qilla Because it's an obvious looking death trap restored into a disguised death trap.

@rzerizrz

4 жыл бұрын

another expert :D

@1badpete999

4 жыл бұрын

@@GGigabiteM the rust was just surface rust if you open any new compressor tank nowadays imported from China they have as much rust inside their tank as this one had on its outside ! But the paint job was awful just a fews can of spray paint would have brought it to the next level ,spending so much time in taking it apart and ruining it at the end , also probably a new set off new cheap bearings would have made it quieter !

@teomaster32

4 жыл бұрын

@@1badpete999 what does the rusty interior do ?

Just wondering about how safe the tank is; it sure looks rusty! I understand you can get them water pressure tested?

i want know machine oil how to clean , and what liquid you used ?

To use that compressor is like having a time bomb in the garage.. and the paint turned out ok btw 😉

@dhcraft9472

5 жыл бұрын

kzread.info/dash/bejne/fYqEwaNwlaq_qNo.html Air compressor explosion safety video footage of actual explosion

@just_a_norwegian

5 жыл бұрын

@@dhcraft9472 the amount of pressure in a tank like that is quite impressive.. so In my garage that thing would not be "restored" might part it out until a better specimen had turned out with a blown engine or something like that.

@dhcraft9472

5 жыл бұрын

@@just_a_norwegian That is how I'm fixing two compressors now. I bought them as new/delivered damage to motor parts but the tanks are undamaged. Silly thing is that the brass fittings which are broken are an uncommon size to find and the manufacture rep wants over £20/$26 for an 10mm x 3/8" compression to male threads which is £5 max part

болгарка с кордщеткой, покраска кисточкой .... эх как все просто и душевно, по гаражному ))

Neat trick to clear all the water from that tank is pour enough denatured alcohol in those tanks to be able to roll the tank around to saturate all the walls with the plugs in all the holes then take the plugs back out and dump out as much as you can and the rest of the alcohol will evaporate the rest of the moisture left

Saludos cordiales ing Felipe, espetacular tu mantenimiento del equipo de aires comprimido. Saludos

I've heard of rusty bottoms in compressors blowing out and leaving a hole in the shop ceiling.

@MH-df6zx

5 жыл бұрын

Not if it was a concrete ceiling.

Такое ощущение что он просто захерачил хороший компрессор пескоструем закинул его в воду на недельку и тип отреставрировал

With well over a million views somebody is doing something right. I for one enjoyed it.

@therestoration2r878

5 жыл бұрын

We are not experts in the field. There are many errors in the video. Very need your advice . Thank you

Ótimo trabalho!! Essa côr ficou melhor que a anterior. Parabéns.

21 minutes in you're using rusty bolts to assemble it?! And painting without primer?!

@lolthien

5 жыл бұрын

This was literally the thing that drove me to the comments. Glad to see someone beat me to it.

@jessemurray1757

5 жыл бұрын

lol, and yet almost 1.4 million views. Its a cruel and unusual world we live in.

@OmegaGamingNetwork

5 жыл бұрын

Glad I am not the only one cringing at this video. Let this video serve as a reminder that some people just don't know what they are doing. Also the complete lack of tape and general awful painting.

@deontaeb5466

5 жыл бұрын

OmegaGamingNetwork more like a repair than a restoration. He apparently had the tools to grind and sand the rust pits and parts clean. He masked a lot of clean up by throwing a thick layer of paint on it. The failure to keep paint off threads and masking of labels etc made me cringe.

@mans4104

4 жыл бұрын

This is and old compressor not a picasso.

lack of experience, so many things half way cleaned and poor paint job

great video. I just swapped tanks for my air compressor.

No gloves? Savage. Thanks for giving us some quality entertainment. Very satisfying to watch.

With so much water drained from the tank, one wonders about the condition of the tank from a safety standpoint. Is there weakness due to corrosion which might not be readily apparent? Good clean up, by the way. What was the coating which you used on the tank prior to painting? Was it a rust converter type of chemical?

@leinad2000b

5 жыл бұрын

I would say the same! A series of errors in this case!

@rogerjoiner2271

5 жыл бұрын

its a ticking time bomb just waiting to explode......too much pressure and then dead people.........

@thefretfiend

5 жыл бұрын

Agreed. That tank should be hydrostatically tested before it is pressurized. BTW, that rust converter was probably Ospho or something similar.

@rogerjoiner2271

5 жыл бұрын

@@therestoration2r878 ...before or after you kill someone???......

@meandyuotube

5 жыл бұрын

I agree, the condition of the inside of the tank is vital. Search KZread for “exploding compressor”. If you attach a warning about this to the video you might save lives. /Best regards M

The engine rebuild was great...but the painting was sloppy...try sandblasting the steel, adding a zinc coat primer and wet sanding, followed by a hammertone spray paint...but generally not bad, except for the gold paint on plastic looks tacky

great job, for a home gamer with little knowledge and simple tools, this turned out great.

Crappy restoration! Love the way you slathered the paint on! If that thing still works in a week I would be surprised!

1. Сомнения в старости компрессора от времени 2. Нахер разберал, так бы и красил 3. У меня бабушка в сарае так дверь отреставрировала, жалко видео не снял

Sorry this was just painting, not an restoration,- no changes of shaft seals, valves, ball bearings etc...

@iagoranieri

5 жыл бұрын

The reservatory is very damaged, because the water

@lyndelbeckwith1706

5 жыл бұрын

He changed the piston rings. In restoration, only change what needs to be changed. If you want to replace everything, knock yourself out.

@steffenreimer257

5 жыл бұрын

​@@lyndelbeckwith1706 Maybe the wrong languare, it need to be disassbled all parts, to have a look which one you need to change/repair. Secondly why he didnt paint all parts separetly, with a brush, sorry looks not that proffesional like it need to be. Off cause, you dont need to changes all bearings, e.g. but you need to check all of them.

@lyndelbeckwith1706

5 жыл бұрын

@@steffenreimer257 Thats true Steffen, but I'mnot sure this guy hasaccess to all of that kind of equipment. He does pretty well with what he has, I think. :)

The work you did is similar to what is done by those who go to your house. you pay a fortune, they do it in a hurry, and it is left with a bungling finish. What time have I lost watching this video

@alwaysopen7970

5 жыл бұрын

I should be outside putting brakes/rotors on my car.

Great project to see. I've got a German compressor, built in 1979 whitch I converted to my wishes. If I'm looking over this project, I think you forgot to connect the earth/ground to the compressor and motor. how much power does the motor have?

Хоть бы болты новые поставил а то ржавые назад прикрутил типо так с завода !

faltou pintar por dentro do tambor .......

Besides just painting over everything, I was a little surprised that with the cylinders off he didn't do a quick hone. You could see it was just put back together. There was even paint over the oil check window. I refurbished an older compressor and even used a rust converter inside the tank to hopefully slow down the rust. He has done a nice job with other projects, but feel this one was just a rush job to get a video out.

@therestoration2r878

5 жыл бұрын

We are not experts. There are many flaws in the project. Need guidance from viewers. Your suggestions are great encouragement for us . Thank you very much

Do you sell your overhauls or keep them? I’d have a tough time letting them go

Poderia ter ficado muito melhor... mas parabéns pelo esforço

@WagnerGoncalves.

5 жыл бұрын

Poderia fazer um serviço bem melhor. Ficou muito mal restaurado.

What kind of painting is that? My kid can do that

良い仕事してますね！ 見入ってしまいます。これからも頑張ってください。

Thanks so much for making this. I’m about to do the same thing so you give me good reference.

you should fill the interior with rust remover too.

Speed Video x2 👍👍👌

Best entertainment ever....I’m at awe at the ability of this man restoring things. I might’ve learn something today. Keep it going.

@therestoration2r878

5 жыл бұрын

Thanks for your comments. Your feedback is a great encouragement for us . Thank you very much

Cara é fera rapaz.

not a restoration but a clean up and paint

@dash9048

5 жыл бұрын

That's what a restoration is

@cmayb1343

5 жыл бұрын

Half ass paint and clean up at that

@ahmeedalaa3787

5 жыл бұрын

@@dash9048 د

I consider that this work is not a restoration. it's a repair only

@jt9498

5 жыл бұрын

Not even a good repair!

Внешний вид - словно ржа рукотворного нанесения. Как оно в естественных условиях так ровненько и тонко ржой покрылось?

A rolling time bomb for the home garage, or what about the rust in the tank? For me it's more appearance than its, I would be afraid to be in the room where such a compressor is running.

А вы не заметили,что он специально ржавчиной покрыт?

It is not restoration, just reassembly with cleanup and painting. And at the end it rises pressure quite slow for two cylinder compressor.

I have a similar compressor, I bought it and found it was seized, took the heads off and found it had water in one cylinder, I let Evaporust sit in the cylinder overnight and that freed it up enough to take the cylinder off. I found the top ring seized in the groove and I broke it trying to un seize it.. The cylinder has deep pitting and seeing as I couldn't find any place that has parts, I cleaned up the cylinder and took the broken ring off, put it back together and it now runs and runs well. In saying that though, I need parts. Where did you buy the rings from and do they sell other parts for the compressor?, ie cylinders.

Good job🇬🇧🇬🇧🇬🇧🇬🇧🇬🇧😍😍😍

Thank you for the entertainment But ,You didn't coat the inside of the compressor with ANY kind of enamel paint against the rust it would have helped its longevity.

The condition of the compressor raises too many questions... Why the receiver is so rusty relative to other components. The piston supercharger is possible in oil, and the electric motor is also in oil? But like there is no. The cover on the electric motor is generally as new. Why do fittings and pressure gauges then look in good condition? The receiver in General how could there be rust? I have the feeling that with him first, especially chemistry washed off the paint, and then direct pour acid or salt solution on it straight rust STAINS. Note that when he removed the electric motor and the piston supercharger, the pads on which they are installed in the MOUNTING PLACES also have an even layer of rust. How is that possible? Was he in the water all the time? If it was in such an aggressive environment that it was covered in rust, why did nothing happen to the sticker on the side of the receiver? Around the sticker you can even see a flat strip, as if it was sealed with something. The paint on the piston supercharger is all in lumps, as after applying the paint remover. All threaded connections are unscrewed easily and naturally, and this is in this state.... By itself, the compressor may not be very new, but not exactly vintage. Don't take people for fools. (google translate)

@MrWolfSnack

5 жыл бұрын

Yes, paint thinner and salt mixture.

@ahmeedalaa3787

5 жыл бұрын

@@MrWolfSnack ذ

Parabéns rapaz por esse trabalho lindo de restauração, ficou perfeito. 100% novo. Ja me inscrevi e com notificações ativadas, tenha de mim 1000 likes. Abraço forte...

may i ask u...before epoxy(silver paint)...what u give before...black color??????

it looks like it wash sprayed with acid, not sat outside for 20 years.

Компрессор современный ! Его , что кислотой облили ? Как-то не серьезно ...

@user-bg1we5hq5b

5 жыл бұрын

Сразу подумал о том же ))

@misha954

5 жыл бұрын

да ты прав, скорее всего компрессор перед видео был обработан уксусом (Оцет)хз как правильно, но реакция на лицо

I found an old air compressor similar to this one with a belt drive on it. I powered it up slowly with a variac and was really surprised to find it had compresson and ran lol. Its gotta be from the 40s lol. I couldnt find any markers on it to tell me the make or model. Ive restore and build tube amps and radios in my spare time and love a good restoration project but im trying to decide if this compressor i found is worth the effort. Still undecided.

Definitely subscribed here. Could I suggest that you check all the bearings... Particularly given the amt of muck on the pistons, it is likely that the bearings have suffered. If they are open frame, then clean and repack. If they are sealed, chuck them and fit new ones.. Looking forward to more restorations. AND. definitely find some way of being certain that the tank is sound.... otherwise you risk... BOOM. Cheers

Хм....такое ощущение, что ты его СПЕЦИАЛЬНО состарил....)))

Когда шлифуешь, полируешь, чистишь детали, то отверстия надо заглушать, иначе пиздец резьбе.

Si la parte de la pintura la hubiera hecho con más ganas le metía el like....

You should have tested the tank in pressure with watter and an hydraulic pump before even starting. At 12-15 bars. Pumps to do the test can be found for around 35-40€. And once you have it you can test your tank every year to make sure it doesn't explode your house (and you) search videos of compressor tank explosion you'll see the results. I would have sandblasted, it's cleaner than what you did, it can be sandblasted for around 20-30€ i think. But it seems like you've applyed some phosphoric acid so it may be good enough.

240v plug WITHOUT GROUND ?!!?!!!!!?!?!!!!!!!?!!????????? 23:15

@roadweary5252

5 жыл бұрын

Or you could have worded it: “Hey man, with a 240v plug you really, really should have a ground on it”

@tomasnovak6177

5 жыл бұрын

Sorry

Nice restoration but very low attention of details

@carlosbalasz5599

5 жыл бұрын

I think the same

@mehdipersian2896

5 жыл бұрын

Very

@zawszeedek

5 жыл бұрын

This is NOT a restoration, this is only clean and paint (nasty paint, I'd say)

@rimmersbryggeri

5 жыл бұрын

@@zawszeedek It's like painting your grandma like a 14 yearold trying to get into a night club? Making up not restoring.

@maxshaila

5 жыл бұрын

@@zawszeedek Agreed... It should have used new bolts, a new strap, brushed the metal, and made a better paint job... new hoses...etc

Good Work😀

16:00 давай, лей воду в цилиндры, не жалей. Вообще то такую очистку проводят заглушив все отверстия.

Почему манометр не закрасил, не понятно?

How rusty is the inside of that bomb if the outside was that rusty

@vaahtoperse18

5 жыл бұрын

3:10 It doesn't look good

@kpb711

5 жыл бұрын

@@vaahtoperse18 must be in a 3rd world country to be wasting time on a 65 dollar compressor with a tank that could explode look up rusty air compressor explosion not pretty

@jeangade5809

5 жыл бұрын

@@kpb711 kan du selv gøre det fjols

@kpb711

5 жыл бұрын

@@jeangade5809 in English?

@blackscreen7812

5 жыл бұрын

@@kpb711 you can do it yourself the danish guy said it to you. And its not about wasting time. You have fun learn stuff and i dont think many of these exist anymore. It will end up on a museum

Really did a disservice to that crank by leaving it in while you cleaned around it.

Not bad. Some work went in and the end product looks a lot better that what you started with.

У вас что дожди кислотные что ли?Как так мог заржаветь?

I left after the really bad paint job...

@AlaskanPotHead

5 жыл бұрын

I left before then, when he put new rings on a still dirty piston.

@ryanturner9778

5 жыл бұрын

Yup, This one was really bad.

@ryanturner9778

5 жыл бұрын

he made it worse than it was originally

@Garth2011

5 жыл бұрын

@@AlaskanPotHead Also didn't hone the cylinders.

@ohhhLuna

5 жыл бұрын

He also didn't clean the bolts before putting them back in.

Was not expecting that paint job

It's mind boggling how you remember how all those parts go back together.

You should replace the power cord with an earthed one, this is currently a death trap.

@netpok

5 жыл бұрын

@@therestoration2r878 Maybe it was not required in the old times when this device was made but now all device needs to be earthed except double insulated ones. If you check the video at 15:05 there is even a broken earth tab on the down-right corner of the terminal block. Just connect it to any holding screw of the electric box and you should be good. Also the power cord looks a little undersized, but that could be the video, just in case you should check it against the amp rating on the motor.

@MH-df6zx

5 жыл бұрын

@@netpok not all countries use the earth wire or have anything earthed.

"""vintage""" but the motor has a recent-looking plastic cover on it.

@brothyr

5 жыл бұрын

@H Biker not typical of electric motors of old. Plastic wasn't thought of as being useful on something that can get warm. Old motors are more likely to have a thin metal box (staring circuits, etc.) or a thin, shaped metal casing for smaller items (capacitor, etc.). Some electric motor companies opted for cast metal boxes but those are largely for big motors for specifically dirty industries where a thing metal box might allow intrusion.

@carlwheezerofsouls3273

5 жыл бұрын

@H Biker lol you just got fucking schooled.

Only second video I've watched. No talk, all work. I'm subscribing.

Very good restoration compressor🔥🔥🔥🔥👍👍👍👍

You forgot to paint the belt.

@Wawashington

5 жыл бұрын

Haytham BuKhadra best comment 😂😂😂😂

@Tyler-ub2bu

5 жыл бұрын

😂

Sempre um excelente trabalho

@therestoration2r878

5 жыл бұрын

Thank you for your encouragement. Hava a nice day

@rafaelaugusto7937

5 жыл бұрын

@@therestoration2r878 thank

@ninomaster4819

5 жыл бұрын

Faltou trocar os rolamentos...

@bryankeithguillory1355

2 жыл бұрын

@@ninomaster4819 al menos empaquétalos con grasa fresca.....

Buenas noches ¿Cual es la capacidad de ese compresor y la capacidad de su pulmón? ¿que liquido estás usando para el lavado de las partes y piezas? Gracias

Did yu do anything to treat the inside of the tank?

Nice final result. Thumb up!

17:16 когда так затягивают, обычно закручивают, например, трубу. Если сплющишь резьбу, горе мастер, то детали пиздец.

Parabens ficou dez 👏👏

c'est du très bon travail une rénovation pleinement réussie, chapeau l'artiste un pouce bleu et un abonné supplémentaire.

Nice! imagine what the inside of the tank is like. I wouldn't tRust it.

@Nando_

4 жыл бұрын

k-boom!

You can see the trails Of whatever chemical they sprayed on the tank to make it look rusty no doubt that's an older compressor but to try to enhance the rust to make it seem worse is a joke

@isolophilia12

5 жыл бұрын

What's the point of hate? Just enjoy the damn video and grow up.

@saknk1

5 жыл бұрын

dude i was thinking the same-thing ! this looks fake ! i like those videos a lot , but this guys ... dont know man ! the motor and compressor got oil all over them but nothing on the tank ,

@hippieconception1408

5 жыл бұрын

@@isolophilia12 cant enjoy a fake video

@hippieconception1408

5 жыл бұрын

@@saknk1 yeah this is a goofy video

@isolophilia12

5 жыл бұрын

@@hippieconception1408 your such a damn child

Good. One suggestion, clean up the nuts and bolts a little more, new cotter pins. Otherwise very nice.

I think you did a decent job of cleaning up and restoring the compressor to a better condition. I'm concerned about the integrity of the tank insides a hydro test would be in order for peace of mind. All in all this is a tool and the people that want to see everything polished to a mirror finish should realize that this is for a shop and not an art museum.

@MrVictorBaarn

5 жыл бұрын

Pressure test should be my first step ,and reading the information plate of the manufacturer. ( pressure testing you do with a inert liquid , not a gas. )