Restoration Burnt Rusted 3 Phase Motor // Restore Stuck 3 Phase Electric Motor
Restoration Burnt Rusted 3 Phase Motor // Restore Stuck 3 Phase Electric Motor
Жүктеу.....
Пікірлер: 49
@rbyaldrzee66579 ай бұрын
Beatiful 👍💯💯
@sheep1ewe2 жыл бұрын
You did the right thing by leaving parts that are not brooken untouched. Nice cleaning and it looks realy nice with the new paint!
@paulfellows2094 Жыл бұрын
great restoration
@Tatal.b2 жыл бұрын
Espetacular !!! Muito bom, belo trabalho. 👏👏👏👏👍👍👍🇧🇷
@antonhajdu8464 Жыл бұрын
in the name of the video you say "burnt motor", but you did not touch the winding?
@larrykelly28382 жыл бұрын
Always replace bearings and did you test the windings? What was wrong with the motor?
@eduardotorres72842 жыл бұрын
El sonido que tiene es de no aber puesto los rodamirntos o cajinetes nuevos por lo demas muy 👍
@davidheidbrink11352 жыл бұрын
Now he has a matching boat anchor to go with the one from last night. You cannot try to clean ball-bearings it just doesn't work, I could heat them whine after he shut the power off
@jeromewhelan6723
Жыл бұрын
Agreed. I was concerned when he gave the bearings a solvent bath withou any scenes of re-lubrication.
@marianbalaz91952 жыл бұрын
Tie loziska nedavaj stare kup nove to neni velka polozka inak vyborne pozdrav zo slovenska🇸🇰🇸🇰🇸🇰🇸🇰🇸🇰🇸🇰🇸🇰
@scorpioneskaju69412 жыл бұрын
what was the restoration? Rust remained on the shaft, the bearings did not replace, but washed in some kind of liquid, it was not easier to put new ones in short, everything through the ass
@robertobezerra83762 жыл бұрын
Fantástico 👏👏👏👏👏👏👌👌👍👍🇧🇷
@DennisFreitas-bn7nh4 ай бұрын
Wow! Coke is cleaner chemicals product 👏👏👏
@williamscheuner60932 жыл бұрын
Never use old bearings, wtf bro
@multitechartelectronicsand54502 жыл бұрын
Super work
@olivierhecbard56102 жыл бұрын
Hey, you are not serious : where is the ground wire ?!!
@wingnut96662 жыл бұрын
might work for about 5 days then seize back up again. almost made a nice rust removing video though.👈🤔
@rechangable44932 жыл бұрын
Great job
@abderrahimhaddanitankioupr93672 жыл бұрын
TAHANKIOU IRMANO
@garggank90836 ай бұрын
You should change the bearings. It would be better. Because the oil inside was damaged. You also need to measure the motor current values. How much current does it draw when operating under load and idle? Are the bearing covers damaged or is there any gap? is checked as
@rogerandlyndabeall38402 жыл бұрын
Just taken out of service pulley still shiney
@richardwyattjr44082 жыл бұрын
That awesome 😎
@nguyenjtuyenhhkgk77572 жыл бұрын
thế này thì có gì mà quay video đâu ! vì ai mà chẳng làm được nó quá là đơn giản chỉ là làm sạch gia công bề ngoài coi như là đồ mới thôi chứ có gì đâu???
@user-wm4yk5tc1e2 жыл бұрын
굿 잡
@fakirkulsofitv15332 жыл бұрын
Süper 💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯
@KOKO-jo6ty2 жыл бұрын
lasy job!!!
@nthuy1892 жыл бұрын
việt nam à
@user-qu6uj6ko2o2 жыл бұрын
베아링을 신품으로 교환해야지요
@KOKO-jo6ty2 жыл бұрын
cleaned and painted!!!!! not restored!!!!!
@DennisFreitas-bn7nh
4 ай бұрын
Cleaned and painted ! = Restored 😂😂😂
@Mohd.Irshad-fl6lv Жыл бұрын
How much cost
@danielli42572 жыл бұрын
Os caras nem pra trocar o rolamento mds,ficou uma carroça o mais importante não fez
@zvonkoar Жыл бұрын
OK ❓❓👍
@user-tf9we3vb1l2 жыл бұрын
سبحان الله وبحمده سبحان الله العظيم عدد خلقه ورضا نفسه وزنة عرشه ومداد كلماته
@ernandoangelo58669 ай бұрын
10
@michael.h.bradley18659 ай бұрын
not spectacularo ! you should always fit new bearings. here endeth the lesson
@Mr.MasterChannel2 жыл бұрын
Playing 2x
@dariuscalitz97042 жыл бұрын
Really misleading tittle, makes you think the motor is burnt aka windings are burnt, and there would be rewinding of motor, and why but why did you "wash" those bearings, all you did was make it easier for small particles to enter and grease to escape, especially the bearing with only dust caps. The way to go if you really had to reuse those bearings is carefully remove dust caps\seals and thoroughly clean the bearings, if you spin it by hand and can't feel\hear any scratching noises, then they are clean and you can apply grease (multi purpose grease is fine if you can't get any bearing grease) and refit the seals.
Пікірлер: 49
Beatiful 👍💯💯
You did the right thing by leaving parts that are not brooken untouched. Nice cleaning and it looks realy nice with the new paint!
great restoration
Espetacular !!! Muito bom, belo trabalho. 👏👏👏👏👍👍👍🇧🇷
in the name of the video you say "burnt motor", but you did not touch the winding?
Always replace bearings and did you test the windings? What was wrong with the motor?
El sonido que tiene es de no aber puesto los rodamirntos o cajinetes nuevos por lo demas muy 👍
Now he has a matching boat anchor to go with the one from last night. You cannot try to clean ball-bearings it just doesn't work, I could heat them whine after he shut the power off
@jeromewhelan6723
Жыл бұрын
Agreed. I was concerned when he gave the bearings a solvent bath withou any scenes of re-lubrication.
Tie loziska nedavaj stare kup nove to neni velka polozka inak vyborne pozdrav zo slovenska🇸🇰🇸🇰🇸🇰🇸🇰🇸🇰🇸🇰🇸🇰
what was the restoration? Rust remained on the shaft, the bearings did not replace, but washed in some kind of liquid, it was not easier to put new ones in short, everything through the ass
Fantástico 👏👏👏👏👏👏👌👌👍👍🇧🇷
Wow! Coke is cleaner chemicals product 👏👏👏
Never use old bearings, wtf bro
Super work
Hey, you are not serious : where is the ground wire ?!!
might work for about 5 days then seize back up again. almost made a nice rust removing video though.👈🤔
Great job
TAHANKIOU IRMANO
You should change the bearings. It would be better. Because the oil inside was damaged. You also need to measure the motor current values. How much current does it draw when operating under load and idle? Are the bearing covers damaged or is there any gap? is checked as
Just taken out of service pulley still shiney
That awesome 😎
thế này thì có gì mà quay video đâu ! vì ai mà chẳng làm được nó quá là đơn giản chỉ là làm sạch gia công bề ngoài coi như là đồ mới thôi chứ có gì đâu???
굿 잡
Süper 💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯
lasy job!!!
việt nam à
베아링을 신품으로 교환해야지요
cleaned and painted!!!!! not restored!!!!!
@DennisFreitas-bn7nh
4 ай бұрын
Cleaned and painted ! = Restored 😂😂😂
How much cost
Os caras nem pra trocar o rolamento mds,ficou uma carroça o mais importante não fez
OK ❓❓👍
سبحان الله وبحمده سبحان الله العظيم عدد خلقه ورضا نفسه وزنة عرشه ومداد كلماته
10
not spectacularo ! you should always fit new bearings. here endeth the lesson
Playing 2x
Really misleading tittle, makes you think the motor is burnt aka windings are burnt, and there would be rewinding of motor, and why but why did you "wash" those bearings, all you did was make it easier for small particles to enter and grease to escape, especially the bearing with only dust caps. The way to go if you really had to reuse those bearings is carefully remove dust caps\seals and thoroughly clean the bearings, if you spin it by hand and can't feel\hear any scratching noises, then they are clean and you can apply grease (multi purpose grease is fine if you can't get any bearing grease) and refit the seals.
I am not like the way use coa goala
🔨🔨🔨🔧🔧🔧👷👷😮😮👍👍👍
Un
Pfusch. Alte Lager! :(((((((
What a joke
Шкив одел на вал задом наперёд. Неуч
💯%💩