Replacing rocker cover gasket and injector seals on a Hilux (1KD ENGINE)
Автокөліктер мен көлік құралдары
Replacing rocker cover gasket and injector seals on a Hilux (1KD ENGINE)
To fix the 2009 toyota hilux/tacoma oil leaking issue coming from the top of your engine, follow these steps in replacing the valve cover gaskets. This is an in depth guide showing you what to remove as well as tips in replacing your rocker cover gasket.
*Disclaimer
We are not responsible for property damage or injury incurred as a result of any of the information contained in this video. Information given in this video does not guarantee the desired outcome. Any injury, damage or loss that may result from improper use of the tools, equipment, or the information contained in this video is the sole responsibility of the user and not carfix
Пікірлер: 42
I would give the area a thorough clean before undoing any fuel pipes, there's risk of intruducing contaminates into the injectors
@Mad21X
2 жыл бұрын
Exactly, I was like 😧
Exactly what I needed to see. Thank you for sharing.
Wow, in 27mins we all know exactly what need to happened when Hilux/Fortuner valve cover need some TLC. Thanks for sharing!
What about packing sealant in specific areas of valve cover?
great video
Great job
Thank you for this video. Very helpful.
Thanks mate 🍺
I DIDN'T see the moment when you took off the top of the electrical injector from the cover, I can see you cut off the video in that moment. Why? Because it's really hard to remove.
@carfix1993
2 жыл бұрын
It's very easy it just connector Press and pull back
شكرا لك من مصر
How did you seal the half moon plug at the end of the camshaft
can you please show how to bleed the fuel lines? Or the engine started even without bleeding?
@carfix1993
25 күн бұрын
Engine can start without bleeding
@dominicco2136
24 күн бұрын
@@carfix1993 Thank you Sir It was very helpful.
What adaptor was used to tighten the nuts of the pipes
@carfix1993
2 жыл бұрын
17 mm crowfoot wrench
What was the reason for replacing the gasket and seals? Was oil leaking??
@carfix1993
2 жыл бұрын
Yes it was bad oil leak
my friend, what torque do you use to tighten the valve cover?
@jemmy5720
2 жыл бұрын
You already have the answer? Because i just broke my bolt nut inside. Now im fck up
@jemmy5720
2 жыл бұрын
I thinks its need specific torque because if too loose , it will still leak. If too tight the bolt broken.
Where did you get the injector seals from? Thanks.
@carfix1993
Жыл бұрын
Toyota dealer
Hi friend, does this also fit the engine of a Land Cruiser 2012 3000 190 horse power draft? Same engine model is the work the same?
@carfix1993
Жыл бұрын
This 1KD engine hilux
@user-ql8ff1he1o
Жыл бұрын
Do you have a spare part for the Land Cruiser 2012 1kd as well?
Captain Bodg😅
After you did the job did you have any lights come on the dash
@carfix1993
2 жыл бұрын
No any light
@nickwinters3657
2 жыл бұрын
Thank you for your reply I have a 120 series if I do it it should OK then yeah
@carfix1993
2 жыл бұрын
Yes you can do it
@niloyu105
2 жыл бұрын
@@carfix1993 for the fuel line injector tight 22nm is this standard for other like Innova thank you new subscriber watching from Al Khafji Saudi Arabia Ads completed...
@carfix1993
2 жыл бұрын
Yes it standard
Im so disappointed in toyota for making a plastic valve cover.have to replace mine cause of cracking
@kudamuyun3173
2 жыл бұрын
Plastic ?? How come.? Its a type of silicone rubber man !
@SonjanetGouws
Жыл бұрын
It's pewter and plastic. Mine cracked after replacing the gasket
@user-yy1cg4qd5n
26 күн бұрын
Jeez ya musta put some tension on it 😂
No no no no es real cortaste ala hora de sacar la tapa de los inyectores y activaste cuando ya está desprendido así no juega Peru
ইনজেকটার খোলা লাগানো ভিডিও বাবান
et tu met pas de silicone dans les 2 coins et au plan de joint des carter ! tu es ouf !