Good work HOWEVER! never remove the rear brackets from the car, this will knock the tracking out needing an expensive 4 wheel alignment!!!! The best way to do it is to pull the bolt out till it touches the fuel tank, then cut it off with a grinder, then pull the rest out. once you have changed the bush and pushed the axle back into the bracket all you have to do is to insert the bolt from the wheel side and put the nut on the inside. It does not matter which way the bolt goes on this part as long as its tightened after your finished! and always always always USE BRAND NEW BOLTS as part of the change, Its them two bolts that holds the whole back axle to the car, If you have had this work done at the dealer have a look under your car and you will see that they fit the new bolts the other way round! Also there is an upgraded bush that is not polly, its a much better bush than the standard ones, part number is (6Q0501541E) or (1ML501541) or (febi 31694) any of these are much better heavy duty bushes but are not quite as hard as polly bushes which are shite on the back end of a golf.

@LarcsWorkshop

Жыл бұрын

Thanks 👍

@05glisedan

10 ай бұрын

I'm in the process of changing the bushing. Drive side, easy. Passenger side, my reaction "What the heck, the gas tank is in the way." This video was very helpful, along with this comment. Thanks to you both.

@toiletgaming2005

7 ай бұрын

great tip about the bolt 👍

Superb video and plenty of good ideas of the use tools most of us have in our garage. Apart from having to either borrow or buy the bush puller it all seems quite easy to do. Thankyou you have probably saved me a small fortune doing it myself instead of letting the MOT garage do the job . I look forward to more VW video jobs .

@LarcsWorkshop

Жыл бұрын

Thanks, no problems 👍

Great idea of yours, i loved these ideas to make work replacements of parts without have to take apart half the car, great please keep making these videos, thank you sir

@LarcsWorkshop

Жыл бұрын

Thanks very much, I'll try🤞

Thanks. Just bought the parts, new nuts and bolts and a mini hack saw!! 😜

@LarcsWorkshop

Ай бұрын

Thanks, no problems. Good luck sorting it out 🤞.

A lot of thanks gor this great video. It is the better about vw rear suspensio bushes. Best regards from Chile 💪😎

@LarcsWorkshop

4 ай бұрын

Thanks, no problems 👍

Well done mate. Just done my mot today and there was advisory regarding this bushes. I'm gonna buy them ASAP and of course buy/ hire the removal set. Anyway great video.

@LarcsWorkshop

2 жыл бұрын

Thanks 😃. Good luck with the repair 🤞. Cheers Larcs 👍

@robinsonlabs

Жыл бұрын

dont get the standard bushes, (6Q0501541E) or (1ML501541) or (febi 31694) any of these are much better heavy duty bushes but are not quite as hard as polly bushes which are shite on the back end of a golf, always use new bolts!

This was the video I was looking for - unfortunately I learnt the hard the way by repairing the rear brake lines and knocking the rear alignment out ;-) - I found Poly Bushings didn't make much difference to the comfort, but super easy to install and do not require aligning. I also replaced rear suspension top mounts and springs. Really like the way you implemented the scissor jack and hydraulic jack, highly recommend 4 wheel alignment after any suspension work.

@LarcsWorkshop

Жыл бұрын

Thanks 👍

Lucky for me the cross member broke from rust and the the new one already came with bushings installed 😅

@LarcsWorkshop

3 ай бұрын

Oh blimey 😳. At least you got it sorted 👌

GoodLord,that's such a tough work for a solo work man XD,especially carry a camera. Enjoy your work and attitude towards life,Larcs. Salute！

@LarcsWorkshop

2 жыл бұрын

Thank you so much, that's very kind😃. Cheers Larcs 👍.

replacing mine with 80 durometer polyurethane next week! along with all other bushings too same poly, cant wait! i love my MK4 Jetta VR6 Sedan so so much, and i have the same wheels! BBS Montreal II! but wrapped in Hankook RS-4 tires (sticky because she gets pushed down b-roads very often)

@LarcsWorkshop

2 жыл бұрын

Sounds great😃. I'm sure you'll feel the difference once you've fitted all of those poly bushes, it'll be like it's on rails👌. I went for 'soft & comfortable' 'old git' rubber bushes 😂. Good luck fitting them🤞. Cheers Larcs 👍

Glad to see a local person on KZread I have a mk4 1.8t golf estate and will be doing the same only I will be polly bushing them. Shame I don't have your workshop 😀. I have subscribed to your channel and now off to find you on Instagram

@LarcsWorkshop

2 жыл бұрын

Thanks, good luck doing the polybushes. They should be easier to fit than the original style 🤞. Mk4 1.8t estate must be a bit rare? Cheers Larcs 👍

@s114rky

2 жыл бұрын

@@LarcsWorkshop they seem to be a rare horse it needs a bit of TLC to bring it up to show room. I am hoping to get into making youtube videos with the repairs/upgrades. Probably see you out and about 👍

@LarcsWorkshop

2 жыл бұрын

@@s114rky nice one👌

Hi, also the bolt that fouled on the fuel tank, this is the same with the Mk7 Fiesta, suggestion when replacing, put back in the other way so the bolt can freely be removed if needed in the future

@LarcsWorkshop

Жыл бұрын

👍

@toiletgaming2005

7 ай бұрын

on the fiesta the brackets dont have adjustment IIRC so its OK to remove them, but on the golfs they have adjustment and you should avoid altering the alignment of them

Well done, I’ve got same job to do on our Jetta and Golf.

@LarcsWorkshop

2 жыл бұрын

Thanks, good luck sorting yours out🤞. Cheers Larcs 👍

@robinsonlabs

Жыл бұрын

dont get the standard bushes, (6Q0501541E) or (1ML501541) or (febi 31694) any of these are much better heavy duty bushes but are not quite as hard as polly bushes which are shite on the back end of a golf, always use new bolts!

Im about to do mine next week just order the bushes and new bolts and the bush install tool. Octavia estate mk1 1.9tdi I fitted new rear shocks now the rear feels like worn out shocks so the bushes are getting replaced hopefully it will feel more stiffened.

@LarcsWorkshop

3 ай бұрын

Good luck sorting it out 🤞.

tricky job u did well pat on back for that one ==good vid

@LarcsWorkshop

2 жыл бұрын

Thanks 👌. Cheers Larcs 👍

Brilliant mate thx for that ....👍

@LarcsWorkshop

2 жыл бұрын

Thanks, no problem😃. Cheers Larcs 👍

Very informative video thank you

@LarcsWorkshop

Жыл бұрын

Thank you very much 👍

I’ve just done the rear bushes on my VW T5, done the arb bushes as well. What an absolute ball ache on a gravel drive. Brake pipe snapped both sides trying to get them out..didn’t have a removal tool like you so set the bushes on fire & then knocked the inner casing out (one took 2 hours as it was rusted to the arm 🤦🏻‍♂️) I was putting poly bushes in so they went back in a lot easier than the standard bushes.

@LarcsWorkshop

Жыл бұрын

Good work sorting it out 👌. They can be a right pain sometimes. I did think about fitting poly bushes but was worried they might be a bit stiff and noisy. How do you find them now they're fitted, any better? Cheers Larcs 👍

@gandhi1078

Жыл бұрын

@@LarcsWorkshop my van is lowered on coilovers so it’s stiff anyway, that’s why I opted for poly bush. Just ordered a set for the front (hopefully easier than the rear 😜)

@LarcsWorkshop

Жыл бұрын

@@gandhi1078 . It'll all be brand new once you've done 👍

Good job chief

@LarcsWorkshop

Жыл бұрын

Thanks 👍

Thanks for the great info video Going to do the job soon so was good to see your job what size spacer did you use to drive in the bearing ?

@LarcsWorkshop

2 жыл бұрын

No problems 😃, thanks for the comment. Sorry, I can't remember what bits I used out of the kit now, it was a while ago. Cheers Larcs 👍

@markcobby8523

Жыл бұрын

Bushing is normally 69mm so anything over 70mm - poly-bushes only require a rubber mallet to tap into place

Thank you from your only Dutch fan.

@LarcsWorkshop

2 жыл бұрын

Thanks 😂👌👍

@markpons7406

2 жыл бұрын

Second dutch fan here.

@frednetherlands887

2 жыл бұрын

@@markpons7406 eindelijk!

@LarcsWorkshop

2 жыл бұрын

@@markpons7406 Whoop, whoop thanks 👌, truly international 🥳. Cheers Larcs 👍

@LarcsWorkshop

2 жыл бұрын

@@frednetherlands887 👌👍

Good morning. Can you tell me where you found the extraction kit, and what is its reference? Thank you for your great video.

@LarcsWorkshop

Жыл бұрын

Hi, I borrowed the kit from a friend but it didn't do the full job. I had to make the rest up with stuff I had around. Cheers Larcs 👍

Thanks for the video. How long did the whole job take you?

@LarcsWorkshop

2 жыл бұрын

Thanks, it's hard to say really. Filming it always takes a lot longer, and getting bits together to fit the new bushes took a while. If you had all of the tools together, it could be done in a morning. I would set a full day aside to do it though. Good luck 🤞. Cheers Larcs 👍

Well done! But wouldn't you grease the new bushings before installing?

@LarcsWorkshop

4 ай бұрын

Thanks 👍. Shouldn't need to as the outer part of the bush is plastic (IIRC).

@steveforbes756

4 ай бұрын

@@LarcsWorkshop 👍🏼

Does anyone know if a manual bearing puller tool would work with removing these bushings? I gotta do this on my mk4 Vr6. i am relectant to buy the tool how important is it really?

@LarcsWorkshop

11 күн бұрын

@@user-qz6kt1dl7e . I don't know of a proper removal tool, they all seem to be advertised as fitting tools. Gotta love a VR6 btw👌.

Much respect for you bud,i own a mk4 golf,and my rear bushes are starting to look tired,i must say you made that look easy,how much did you pay for the hydraulic stand if you don't mind me asking,great video my friend..well done.👍

@LarcsWorkshop

Жыл бұрын

Thanks, they weren't too bad, just awkward and a bit time consuming. I got the QuickJacks second hand off Facebook market place for £750. Cheers Larcs 👍

@markcobby8523

Жыл бұрын

If it helps, I was able to get plenty of height with axel stands using two hydraulic jacks and blocks of wood. Brick the front wheels and combine jacks and axel stands for extra safety when clubbing the old bushings out. the plastic bush are easier to remove. Some have older metal housed busing, these take a bit more work but same process.

@LarcsWorkshop

Жыл бұрын

@@markcobby8523 👍

Hey! Can I replace rear bushes of 2 sides, without cut brake pipes? Thanks

@LarcsWorkshop

Жыл бұрын

Yes, just be careful. Cheers Larcs 👍

Hello Sir. Where do you buy this car elevator system ?. Congratulations for your video.

@LarcsWorkshop

2 жыл бұрын

Hi & thanks, they're called QuickJacks and I bought them used from Facebook Marketplace. I did a video about them ( kzread.info/dash/bejne/qZis1secYbfgXco.html ). Cheers Larcs i

What size of the flapper wheel did you use ? Thanks in advance fir reply

@LarcsWorkshop

Жыл бұрын

Thanks, I think it was a 60mm diameter flapper wheel. Cheers Larcs 👍

Hi Larcs just want to know, my back tires wore out the inside tread. What could be the problem? is it this axle bushes you replace here? I have a Golf 4 1.6i 2003

@LarcsWorkshop

2 жыл бұрын

Could be, best to have a visual of them and see if they are worn out. Good luck. Cheers Larcs 👍

@robinsonlabs

Жыл бұрын

dont get the standard bushes, (6Q0501541E) or (1ML501541) or (febi 31694) any of these are much better heavy duty bushes but are not quite as hard as polly bushes which are shite on the back end of a golf, always use new bolts!

Que diámetro tiene el buje metálico más chico con el que saca el buje de hule?

@LarcsWorkshop

2 жыл бұрын

Sorry, I can't remember what size it was.

They are 16mm bolts & nuts, not 17mm. Learned the hard way when rounded off bolt head using a 17mm...

@LarcsWorkshop

Жыл бұрын

Thanks👍

What do you think of the ride after a longer time of running with them new bushes?

@LarcsWorkshop

Жыл бұрын

Back to standard really. Felt a little more predictable when pushing on a bit. Happy with the results thanks. Cheers, Larcs 👍

Poly bushes would be / are far easier. Like the way you removed the bushes though.

@LarcsWorkshop

Жыл бұрын

Thanks, I agree about poly bushes but at my age I need comfort over sportiness 🤣. Cheers Larcs 👍

@robinsonlabs

Жыл бұрын

dont get the standard bushes, (6Q0501541E) or (1ML501541) or (febi 31694) any of these are much better heavy duty bushes but are not quite as hard as polly bushes which are shite on the back end of a golf, always use new bolts!

@LarcsWorkshop

Жыл бұрын

@@robinsonlabs Thanks 👍

should have put those bolts the correct way, from outside

@LarcsWorkshop

2 жыл бұрын

Thanks, I thought about it, but then just put them back the way I found them. Cheers Larcs 👍

🇳🇴👍🏻😊

@LarcsWorkshop

10 ай бұрын

Thanks 👍