No video
Replacing Cabin Air Filter in 2012-2013 Mazda 5
Replacing Cabin Air Filter in 2012-2017 Mazda 5
Sorry, but windows movie maker introduce noise.
If you like this video please support with purchasing parts below:
This is the Cabin Filter I used: amzn.to/2JH7sQG
Пікірлер: 23
I found you don't have to disconnect the wire connectors. They pull away with the filter panel. You DO need the stubby screwdriver for that very difficult 4th screw which I am not putting back.
What kind of evil MONSTER designed this to be so difficult? I’ve got broad shoulders I can’t even fit in there to find the screws!!!!
Thank you! I relied on this video to replace the cabin air filter on my 2012 Mazda5. It was a PAIN! I will NEVER again replace the filter myself. What a pain!
WHO EVER DESIGNED THIS IS INDEED A MONSTER I work at a dealership (not Mazda) but had to do these filters since it was a trade in. Just so you all know the labor time for this is 50 min and that's for experienced technicans who you would expect to do it fast than at home jobs. If you are doing this at home good for you and good luck, expect it to take more than an hour.
Thank you for the video. Have. 2014 Mazda 5, can confirm that it’s 4 screws and the electrical as are not necessary to remove (although if you did, you’d get a bit more room to get that annoying 4th screw at the top). Hand screwed the 4th one back in and then tightened with a stubby. Fortunately I’m still young enough to get down in that very uncomfortable position). Paid $25 for the filter and put in 15 min for the install. Versus the $85 dealer was charging! Will do again in the future
After owning several Toyotas, I must say... this some bullshit. LOL
Great video of the change😊
Sometimes I have to remind myself that engineers are people too and not just demons sent up from the depths of hell to torment me.
@wetcarpet7537
2 ай бұрын
They retards for sure
Great video! Thank you very much. I'm attempting this soon so wish me luck with less than an hour. Sidenote - I've always thought stubby's should be called chubby's too 😅
Great directions, thanks! But an awful job, kept thinking I should have paid the dealer to install it! lol But I did get it done and all screws back where they belong. There are 5 screws, btw.
No. there are two push latches the you can release at the front and the panel will drop down. It is held in at the back by a slot fit, so no latching.
Thank you. I'll check that area again and let you know.
my question is i ordered the TYC 800023P2 as per your video , but it says it is not the correct filter did your work!
@sigor2011
10 жыл бұрын
Ya, Stupid Amazon parts identifier is not working correctly. It is listed as Mazda 3 part but not Mazda 5, even though they use the exactly same filters. Don't worry, as long as you get that part number, it will work.
Comrade! My 2013 Mazda5 has 4 screws, more or less just like yours, bot with one more. However, when all 4 are out, the cover is loose, but something else has snagged it in the top forward corner! Any ideas?
@sigor2011
5 жыл бұрын
There is a small screw on the top. I can't recall now if 4 or 5 screws total. Top screw was the worst, I did not bother putting it back in.
This job is a BEAR to do. Accessing all the screws is challenging enough, but the video skips the most difficult part - installing the bottom filter while holding the top on in place. There is no guide inside the housing to hold the filters in place. They basically just get pushed up against the internal fins. I used a screwdriver to hold the upper one while guiding the lower filter into the upper filter groove. All while face up lying across the door threshold and arms jammed into footwell. When I get out of traction I’m going to pay Mazda a visit....
Did you remove the glove compartment door first to get under the panel?
Thanks for the info!
Thank u sir
That top right screw ...
Same as the old mazda 5