What's the name of the tool he used to pull the cb axle out?
@sigor201115 сағат бұрын
@@josemorales5117 forgot, sorry
@user-yy5zi4cv4l14 күн бұрын
thanks bro, just did mine 2012 mazda5
@darkbeach7220 күн бұрын
2 comments: First, I used Amazon description: 580mAh 3.7v LiPo Battery Replacement for Jabra Evolve 75 Bluetooth Headset, Evolve 75 UC Battery,Evolve 75 SE Battery Replacement,AHB572535PST Battery Upgarde Brand: AOLIKES This battery did not require any connector modification, it was completely plug and play for my unit. Second, the tab where the first T4 screw is removed, can pivot and rotate 180, according to gravity, such that the tab is not available upon reassembly, so keep an eye on that tab, and make sure the hole for the T4 is pointed UP when you reassemble the left earpiece. Thanks for the video.
@Kira-xv4te22 күн бұрын
This might be the most complicated to open car.
@kataklysmdlАй бұрын
An addendum to this problem. After replacing the roller I noticed the roller would fall out of the track. The track on my car was moving down as the door slid back. The reason was the nut was loose and allowed track movement and the sliding roller was falling off. So when you closed the door it pushed on the rubber. So I had to unsnap the plastic inside the car to reach and tighten that nut so the track would stay in place, solid. The door worked as new after that with tight track and a new roller.
@teoceknАй бұрын
Awesome video . helped me contributed 1 less item to e-waste.
@kurtengel60292 ай бұрын
i recognize those crappy tire screwdrivers
@thesmuler56272 ай бұрын
Circuit design usually employ resistors in parallel with capacitors to drain them almost immediately but that is a good practice when removing airbag just in case.
@nishadesai83562 ай бұрын
Which Screw Driver you have used to open to screw.? Any link for good screw driver which I can get from Amazon.?
@sigor20112 ай бұрын
www.amazon.com/dp/B00MUJU33S
@nishadesai83562 ай бұрын
@@sigor2011 Thank you so much @sigor2011 for providing Amazon URL. Which Screw driver generally you have used to open the screw in Jabra Evolve 75 headphone.? T3/T4/T5/T6/X ??
@sdrivegarage2 ай бұрын
Thank you. I can confirm that this fixes a sticky door. My rollers were not obviously broken like yours, but the door was extremely difficult to close. After replacement, it's smooth like butter.
@cssAldi2 ай бұрын
05:27 best part
@jeffcastillo90632 ай бұрын
I replaced my blend door actuator, but now my ac wont turn on. The ac light blinks.
@sigor20112 ай бұрын
Unless you did something wrong, those should not be related. I had the same, and ended up rhat A/C charge level was too low, ended up being leaking AC condesnsor.
@jeffcastillo90632 ай бұрын
@sigor2011 Thanks for the reply. I actually let it run for awhile, and then turned my truck off and on. It started working, probably just needed to reset.
@md.emdadulhaque2062 ай бұрын
Hi! I watched your KZread channel and your content is very good. I am a big fan of your. I have proven strategies for optimizing KZread content to rank higher in search results. Let's work together to optimize your video titles, descriptions, and tags for maximum visibility. Thanks
@CopperheadArcher3 ай бұрын
Thank you for this video it has solved a great problem for me!
@Jimiish3 ай бұрын
used this guide today on a 2014 ... thanks worked like a charm
@YoGhostface3 ай бұрын
Excellent video! That seemed like a lot of work (for me) but watching you do it step by step makes it a possibility for me. Thanks!
@sayedhofiani80413 ай бұрын
will this fix the issue with one side (the battery side) not working.
@sigor20113 ай бұрын
No idea. Your issue sounds more like a broken wire.
@Henrik196702024 ай бұрын
Thank you! You just saved another headset.
@jameslund2215 ай бұрын
Good job 👍🏻
@medaveon5 ай бұрын
Thank you! Great video, so helpful.
@Charles_-zw6zk5 ай бұрын
Does Mazda specify the torque for this anywhere? On my NKG plugs it illustrates the torque with the amount of turn you should do, but I rather had a number.
@sigor20115 ай бұрын
Probably, I just use the turn count as suggested. Torque number hard to apply as long extension make it harder to reach. I don't kmow anyone using Torque wrench
@ankorot6 ай бұрын
thank you! btw, i use these headsets for 4 years and i replace them every 2 years because mic stops working: battery has never died but mics die regularly due to movements up and down and cable breaks
@lwrgbr6 ай бұрын
great video, our car has this problem, will take to dealer tomorrow
@sigor20116 ай бұрын
I you got the tools, parts are cheap enough to throw at the problem and hope for the best or just pay the dealer to do the work skipping diagnostic fee. So far I had no further issue with this message.
@Bignene6286 ай бұрын
Why not remove the booth easier
@sigor20116 ай бұрын
If works for you, go for it! I was not able to even afternremoving the retaining ring as seemed glued on and I did not want to rip it.
@agh0x016 ай бұрын
Procedure for Voyager V4220 is very similar to this, but the tiny battery is in the same side of the headset as the microphone, micro USB port, etc. The battery is different to the example in this video as it is has the code 1ICP4/25/38 (25 x 38 mm, I believe), and has 3 wires (red, white, black) instead of 2. Looks like the white wire could be related to battery temp monitoring, or validating that the battery is supported by the device.
@lspudpage7 ай бұрын
Thanks so much for your video. My speaker had stopped working on the battery side and I had no clue how to get inside to take a look. It was a broken wire, soldered in a replacement, all back together and working. You've saved me the cost of a replacement.
@Rikky20007 ай бұрын
Thanks for the video. Just replaced the battery on Jabra 75 which was completely broken. Now good as new, and the battery I ordered had the correct connector. Thank you!
@marcoflaviosolanorodriguez88165 ай бұрын
Hello my friend, Do you mind sharing the battery you bought that had the right connector?
@SK-qv5cm4 ай бұрын
Same question as @marcoflaviosolanorodriguez8816 said here, would you mind please sharing the battery info of the one that had the correct connector?
@TexaSurvival7 ай бұрын
My air blows cold but after a few minutes of startup, the air seems to get restricted at the vents and then blow behind the dash (sounds like defrost but I don’t feel anything up there). My set up is exactly like this one, no dual zone or anything, so which one needs replacing? Another video says my problem is the mode actuator and that it is on the driver side but your description here makes it seem like the one behind the radio.
@sigor20117 ай бұрын
There are a few actuators there. Often they are sold in a pack, can replace borh.
@slammedcc7 ай бұрын
Thank you! My 2003 CRV starts again. I struggled for an hour with the small screw on the back of the ignition switch until I ran to the hardware store and got a long, thin, phillips head screwdriver. Came right out.
@apkungen897 ай бұрын
You can also calculate it. P = U * I which leads to Wh = V * Ah -> Ah = 1,3/3,7= 0,3514 Ah = 351 mAh
@sdrivegarage8 ай бұрын
Thank you! Great job. You told me what I need to know without a lot of extra talking. I only wish I had replaced this part before I broke the handle trying to slam the door harder and harder. Sigh.
@reynierhernandez82608 ай бұрын
You do not need to remove the nut simply pull back on the arm and it gives you plenty of room to remove the blade
@sigor20118 ай бұрын
I did not have your luck. Broke the internal spring 1st rime. Removal prevented that issue on the 2nd change.
@Phalgun278 ай бұрын
what is the size of the heat shrink sleeve? what dia should we use?
@sigor20118 ай бұрын
Smallest you can get.
@raymondlaser8 ай бұрын
Thanks ;) Battery swapped. Everything works.
@user-mh1ey2pz9f8 ай бұрын
А при замене модуля надо ли снять клеммы с аккумулятора
@sigor20118 ай бұрын
I did not bother.
@lisamcbride55738 ай бұрын
Thank you so much. I have yhe sme washer with same problem!! This was a big help
@buddydudeguy58598 ай бұрын
There is no need to remove the blade arm assembly from the car. Once the plastic clip/cover over the nut is removed, you can pull the blade assembly away from the window and the blade can easily be rotated out of the arm.
@sigor20118 ай бұрын
I did not have this luck. Spring.inside the arm prevented this.
@iplparm9 ай бұрын
Awesome, thank you!
@jimcopeland40119 ай бұрын
That 8mm deep socket threw me for a loop! Thanks for specifying the size!
@user-xt8mr1cx8u9 ай бұрын
Nice work 🙏thanku ❤
@armandoramos19499 ай бұрын
Thanks for sharing, you made that look so easy.
@RottenTaco1879 ай бұрын
Thanks easy install. I could reach the camera from underneath the bumper.
@paulb4uk9 ай бұрын
Nice one mine would benefit from a new battery .
@linzeng65239 ай бұрын
Fixed mine with a piece of rubber tubing which I inserted over the piece of rod to reestablish the proper contact. No new parts, no visit to the dealers, took less than 10 min. It’s been months and working fine.
@cityhicks9 ай бұрын
I just did this exact thing yesterday. Super easy. I also bent the microswitch arm down a little so it makes better contact. It really seems like a waste of $ to replace the entire assembly.
@geezer53578 ай бұрын
Admire your diagnostic chops and ingenuity. Do you mean that you used the tubing as a sleeve over the lever/rod to make it thicker? Was this just some tubing you happened to have lying around...? 🥸 I think I've just about figured out what you mean, but I wouldn't know where to put my hands on exactly the right diameter and thickness of tubing to achieve this?! Any pointers gratefully received-- not mechanically inclined, or usually a tinkerer, but foolhardy enough to try!
@geoffrey12114810 ай бұрын
What’s the best radio can anyone give me the name on this radio thanks 😊
@dannydawson893410 ай бұрын
Where can I get this radio for my Mazda 5
@sigor201110 ай бұрын
I'd say Amazon or ebay. Place I got from.is closed. Maybe aliexpress?
@philliptoone10 ай бұрын
What about the camber angle? Is that affected when you remove the two strut bolts?
@sigor201110 ай бұрын
Not sure. It may be affected but I did not not check on the alignment machine after. They are not camber bolts, so I did not worry.
@philliptoone10 ай бұрын
@@sigor2011 Thanks for the info. I'll not worry about camber angle.
@user-nn9xn3vi8n10 ай бұрын
Do you have any videos of the wiring? I need to reattach some in my headset.
@sigor201110 ай бұрын
Sorry, no
@Catalinbut10 ай бұрын
thanks for posting this - very helpful. it would be a shame to have to change a perfectly working headset only because of the battery
@kenyoung422210 ай бұрын
After several weeks of frustration, this was finally repaired under the Voltec Component Warranty per Technical Service Bulletin 19-NA-206 at no charge by a "REPUTABLE" GM dealership, Dave Kirk in Crossville, TN. Shout out to Leteshia (GM's/BBB customer service representative" and the customer service staff at Dave Kirk Chevrolet!"
Пікірлер
What's the name of the tool he used to pull the cb axle out?
@@josemorales5117 forgot, sorry
thanks bro, just did mine 2012 mazda5
2 comments: First, I used Amazon description: 580mAh 3.7v LiPo Battery Replacement for Jabra Evolve 75 Bluetooth Headset, Evolve 75 UC Battery,Evolve 75 SE Battery Replacement,AHB572535PST Battery Upgarde Brand: AOLIKES This battery did not require any connector modification, it was completely plug and play for my unit. Second, the tab where the first T4 screw is removed, can pivot and rotate 180, according to gravity, such that the tab is not available upon reassembly, so keep an eye on that tab, and make sure the hole for the T4 is pointed UP when you reassemble the left earpiece. Thanks for the video.
This might be the most complicated to open car.
An addendum to this problem. After replacing the roller I noticed the roller would fall out of the track. The track on my car was moving down as the door slid back. The reason was the nut was loose and allowed track movement and the sliding roller was falling off. So when you closed the door it pushed on the rubber. So I had to unsnap the plastic inside the car to reach and tighten that nut so the track would stay in place, solid. The door worked as new after that with tight track and a new roller.
Awesome video . helped me contributed 1 less item to e-waste.
i recognize those crappy tire screwdrivers
Circuit design usually employ resistors in parallel with capacitors to drain them almost immediately but that is a good practice when removing airbag just in case.
Which Screw Driver you have used to open to screw.? Any link for good screw driver which I can get from Amazon.?
www.amazon.com/dp/B00MUJU33S
@@sigor2011 Thank you so much @sigor2011 for providing Amazon URL. Which Screw driver generally you have used to open the screw in Jabra Evolve 75 headphone.? T3/T4/T5/T6/X ??
Thank you. I can confirm that this fixes a sticky door. My rollers were not obviously broken like yours, but the door was extremely difficult to close. After replacement, it's smooth like butter.
05:27 best part
I replaced my blend door actuator, but now my ac wont turn on. The ac light blinks.
Unless you did something wrong, those should not be related. I had the same, and ended up rhat A/C charge level was too low, ended up being leaking AC condesnsor.
@sigor2011 Thanks for the reply. I actually let it run for awhile, and then turned my truck off and on. It started working, probably just needed to reset.
Hi! I watched your KZread channel and your content is very good. I am a big fan of your. I have proven strategies for optimizing KZread content to rank higher in search results. Let's work together to optimize your video titles, descriptions, and tags for maximum visibility. Thanks
Thank you for this video it has solved a great problem for me!
used this guide today on a 2014 ... thanks worked like a charm
Excellent video! That seemed like a lot of work (for me) but watching you do it step by step makes it a possibility for me. Thanks!
will this fix the issue with one side (the battery side) not working.
No idea. Your issue sounds more like a broken wire.
Thank you! You just saved another headset.
Good job 👍🏻
Thank you! Great video, so helpful.
Does Mazda specify the torque for this anywhere? On my NKG plugs it illustrates the torque with the amount of turn you should do, but I rather had a number.
Probably, I just use the turn count as suggested. Torque number hard to apply as long extension make it harder to reach. I don't kmow anyone using Torque wrench
thank you! btw, i use these headsets for 4 years and i replace them every 2 years because mic stops working: battery has never died but mics die regularly due to movements up and down and cable breaks
great video, our car has this problem, will take to dealer tomorrow
I you got the tools, parts are cheap enough to throw at the problem and hope for the best or just pay the dealer to do the work skipping diagnostic fee. So far I had no further issue with this message.
Why not remove the booth easier
If works for you, go for it! I was not able to even afternremoving the retaining ring as seemed glued on and I did not want to rip it.
Procedure for Voyager V4220 is very similar to this, but the tiny battery is in the same side of the headset as the microphone, micro USB port, etc. The battery is different to the example in this video as it is has the code 1ICP4/25/38 (25 x 38 mm, I believe), and has 3 wires (red, white, black) instead of 2. Looks like the white wire could be related to battery temp monitoring, or validating that the battery is supported by the device.
Thanks so much for your video. My speaker had stopped working on the battery side and I had no clue how to get inside to take a look. It was a broken wire, soldered in a replacement, all back together and working. You've saved me the cost of a replacement.
Thanks for the video. Just replaced the battery on Jabra 75 which was completely broken. Now good as new, and the battery I ordered had the correct connector. Thank you!
Hello my friend, Do you mind sharing the battery you bought that had the right connector?
Same question as @marcoflaviosolanorodriguez8816 said here, would you mind please sharing the battery info of the one that had the correct connector?
My air blows cold but after a few minutes of startup, the air seems to get restricted at the vents and then blow behind the dash (sounds like defrost but I don’t feel anything up there). My set up is exactly like this one, no dual zone or anything, so which one needs replacing? Another video says my problem is the mode actuator and that it is on the driver side but your description here makes it seem like the one behind the radio.
There are a few actuators there. Often they are sold in a pack, can replace borh.
Thank you! My 2003 CRV starts again. I struggled for an hour with the small screw on the back of the ignition switch until I ran to the hardware store and got a long, thin, phillips head screwdriver. Came right out.
You can also calculate it. P = U * I which leads to Wh = V * Ah -> Ah = 1,3/3,7= 0,3514 Ah = 351 mAh
Thank you! Great job. You told me what I need to know without a lot of extra talking. I only wish I had replaced this part before I broke the handle trying to slam the door harder and harder. Sigh.
You do not need to remove the nut simply pull back on the arm and it gives you plenty of room to remove the blade
I did not have your luck. Broke the internal spring 1st rime. Removal prevented that issue on the 2nd change.
what is the size of the heat shrink sleeve? what dia should we use?
Smallest you can get.
Thanks ;) Battery swapped. Everything works.
А при замене модуля надо ли снять клеммы с аккумулятора
I did not bother.
Thank you so much. I have yhe sme washer with same problem!! This was a big help
There is no need to remove the blade arm assembly from the car. Once the plastic clip/cover over the nut is removed, you can pull the blade assembly away from the window and the blade can easily be rotated out of the arm.
I did not have this luck. Spring.inside the arm prevented this.
Awesome, thank you!
That 8mm deep socket threw me for a loop! Thanks for specifying the size!
Nice work 🙏thanku ❤
Thanks for sharing, you made that look so easy.
Thanks easy install. I could reach the camera from underneath the bumper.
Nice one mine would benefit from a new battery .
Fixed mine with a piece of rubber tubing which I inserted over the piece of rod to reestablish the proper contact. No new parts, no visit to the dealers, took less than 10 min. It’s been months and working fine.
I just did this exact thing yesterday. Super easy. I also bent the microswitch arm down a little so it makes better contact. It really seems like a waste of $ to replace the entire assembly.
Admire your diagnostic chops and ingenuity. Do you mean that you used the tubing as a sleeve over the lever/rod to make it thicker? Was this just some tubing you happened to have lying around...? 🥸 I think I've just about figured out what you mean, but I wouldn't know where to put my hands on exactly the right diameter and thickness of tubing to achieve this?! Any pointers gratefully received-- not mechanically inclined, or usually a tinkerer, but foolhardy enough to try!
What’s the best radio can anyone give me the name on this radio thanks 😊
Where can I get this radio for my Mazda 5
I'd say Amazon or ebay. Place I got from.is closed. Maybe aliexpress?
What about the camber angle? Is that affected when you remove the two strut bolts?
Not sure. It may be affected but I did not not check on the alignment machine after. They are not camber bolts, so I did not worry.
@@sigor2011 Thanks for the info. I'll not worry about camber angle.
Do you have any videos of the wiring? I need to reattach some in my headset.
Sorry, no
thanks for posting this - very helpful. it would be a shame to have to change a perfectly working headset only because of the battery
After several weeks of frustration, this was finally repaired under the Voltec Component Warranty per Technical Service Bulletin 19-NA-206 at no charge by a "REPUTABLE" GM dealership, Dave Kirk in Crossville, TN. Shout out to Leteshia (GM's/BBB customer service representative" and the customer service staff at Dave Kirk Chevrolet!"