Replaced all bloated capacitors but still no backlight?!
This TV has no backlight, and all defective capacitors have been replaced but still no backlight. Tips and tricks. please like share and subscribe.
This TV has no backlight, and all defective capacitors have been replaced but still no backlight. Tips and tricks. please like share and subscribe.
Пікірлер: 65
Just did one myself 3.3v rail capacitor. Diagnosed using hot and cold on capacitors to pinpoint problem. After replacing it worked and bad capacitor read correctly at 47uf but I guess had bad ESR. It wasn't bloated either. Can never trust an electrolytic like a politician.
@dexternengomasha7579
2 ай бұрын
😂😂😂
Thank you for the tutorial. I learned capacitors can also be a root problem too backlight issues. Keep up the good work.
Thank you for sharing your wisdom 🇰🇪
MAESTRO thank you very much for the video.👍
Great mastar❤❤
nice work master 👍👍👍
Good job 👍.
Nice vedio sir
Keep up the good work Sir u a d best thanx a lot
Great teacher
@tevzTVTevatronics
2 ай бұрын
Thank you! 😃
Greater job
I Like this too
❤ thanks sir for knowledge
Hello. Please show us always the model number on the sticker on the backside of the TV. Good video's and good job. Thanks. Andy.
Good job..
Werey good job sir thanks for you
Goodjob master
❤❤ thank you sir❤❤ ❤❤u r great teacher❤❤
Good job
Thanks for this video sir
Thax alot
Please give me a link to buy single leds for backlight which you are using when strips not available
Good sir
Thank you sir ..
watching master
Please provide a link to the store where you can buy these diodes that you insert instead of strips illuminating the matrices in LED TVs. Pozdrawiam z Polski.
Nice information sir
ممتاز جدا اتابعك من العراق 🎉
thank you sir
good
bL tester can be use to check the defective backlights
👍
Love You sir🇧🇩🇧🇩🇧🇩🇧🇩
🤟
Sir, can you tell me what is the value/ marking of the rectifier diode? Because mine is burn out. Thank you!
👍👍👌👌
I am from pakistan
@Afridikhan-he5kc
2 ай бұрын
Sir I need your WhatsApp number I am mechanics led tv
Tevz bey emeğine sağlık . Kalitesiz kapasitör kullanılmış. Led sürücü den sonra led tamiri yaptınız. Acaba kaç yıl sonra led patlar. . Teşekkürler hocam.
@tevzTVTevatronics
2 ай бұрын
3 to 4 years
Mr . Tevz you must first testing the led driver first when you measure the voltge
@tevzTVTevatronics
2 ай бұрын
That is exactly what I did.
@mahmoudnaser453
2 ай бұрын
No,you first Chang tow capistane 470mf/16v&10v,I think so
@tevzTVTevatronics
2 ай бұрын
@@mahmoudnaser453 because they are bloated, and first seen on the video. I known they are not the reasons why the driver is not working. If I dont changed it may viewers ask why?I hope you understand.
@bruno241084
Ай бұрын
Great tehc
@bruno241084
Ай бұрын
I love this man...very smart
Is the back light 3 rows each 7 bulbs connected two rows in parallel and one in series? If all bulbs in series the voltage required is 21x6 volt= 126 but it lits up at 70V hence my doubt.
@tevzTVTevatronics
2 ай бұрын
they all connected in series, the LEDs are 3 volts
Sir, a personal question? Are you a member of an IP Tribe? Just listened to the background conversations and heard some accents that sounds familiar. Thanks.
@tevzTVTevatronics
2 ай бұрын
hahaha hindi
Helo Sir, does Sharp TV will light-up when the main board not connected ? Note : My TV has Power board and Main board separated.
@tevzTVTevatronics
2 ай бұрын
No idea
Pleaae show your fork type testing probe in next video
@tevzTVTevatronics
2 ай бұрын
fork probe? clip and high voltage probe all I have.
@bineshchauhan8713
2 ай бұрын
@@tevzTVTevatronics I am from India how can get it
Please change all the led strips otherwise the same problem may occur soon (because other led bulbs life will be reduced so same problem will occur again soon) Thanks
sir, saan ang calibration center ng fluke multimeter dito sa pilipinas? salamat
@tevzTVTevatronics
2 ай бұрын
Negative idea
why didnt use led tester
@tevzTVTevatronics
2 ай бұрын
Multi tester can test it
Your diagnosis bit confusing 1 St you said backlight not glowing & Measured backlight voltage is not boosting then why are you going to 12 volt & 5 volt lines instead of backlight section.
@aneeshk.p4281
2 ай бұрын
Sometimes addressing the visible issue, like a bloated capacitor, is the first step in troubleshooting. It's essential to fix any obvious problems before diving deeper into more complex or hidden ones. This can help prevent further damage and ensure a more thorough inspection of the system.
Good job