Renault Clio 2 2003 Project - HOW TO CHANGE GEAR KNOB + BOOT SHIFT

Ғылым және технология

Please Like/Share & Subscribe
Official Website: bit.ly/2jAUq9h
Facebook: bit.ly/2iEFirI
Instagram: bit.ly/2iMISeq
KZread Siep Online Official: bit.ly/2jCf60a
Official Twitter: bit.ly/2iEGOtG
Google Plus: bit.ly/2jB4Gyd
-The soundtrack was provided by NCS: Tobu - Roots NCS Release
-The 2nd soundtrack was provided by NCS: Max Brhon - The Future [NCS Release]

Пікірлер: 24

  • @luca_m__1279
    @luca_m__12795 күн бұрын

    I've finally changed it. If you can't push it down like in the video: I've put on the lever and in the handle hole some motor grease. Later I put the new handle rotating it in the lever (not pushing) with the help of big work gloves. It fitted perfectly.

  • @ctg-358
    @ctg-358 Жыл бұрын

    very helpful for my old 2001 Megane, too. So I knew, after watching this video, that it is not possible to get the knob off without destroying it. Made it easy like you did. Cutting it off, cleaning it and putting, pressing the new knob with a bit of glew onto the shift. Is looking perfect

  • @cfunkful
    @cfunkful3 жыл бұрын

    Thanks bud

  • @DanSS1.4
    @DanSS1.4 Жыл бұрын

    Good....now i want to buy the same media player from your car....where do i find that model?

  • @AI.MadeTechReviews

    @AI.MadeTechReviews

    4 ай бұрын

    Aliexpress

  • @demisdgs8481
    @demisdgs8481 Жыл бұрын

    για τρακτερ καλο ειναι

  • @dezmond91_hu
    @dezmond91_hu Жыл бұрын

    sorry, but it looks like shite. the hole is not big enought or what? there is a big gap. also: the metal part will burn your hand in the summer. i'm planning to change mine because it's scratched, there is no way to remove the stock knob without damaging it?

  • @AI.MadeTechReviews

    @AI.MadeTechReviews

    Жыл бұрын

    I covered the gap with a ribbon, easy to find and very cheap. Looks awesome

  • @funnypepe

    @funnypepe

    Жыл бұрын

    @@AI.MadeTechReviews why ribbon ? just push knob more in =).

  • @AI.MadeTechReviews

    @AI.MadeTechReviews

    Жыл бұрын

    I didn't want to hammer it

  • @idontcare7961

    @idontcare7961

    Жыл бұрын

    @@AI.MadeTechReviews You could have used blow torch on the inside of the new knob hole to slightly melt the plastic and while still soft easily push it in the place where it will pretty much weld itself onto the grooves of the shaft and stay there securely and all the way to the end removing the gap.

  • @3laino

    @3laino

    5 ай бұрын

    I saw that to, looks bad I already bought this stuff.. the boot looks nice though. If I can't get it all the way in going to cut the level a lil shorter 😅

  • @Dragon9Nexus
    @Dragon9Nexus11 ай бұрын

    So basically you had no idea on how to do it but decide to make a video about it, and in the end not even placing it fully?? 😂👎🤣

  • @marvintopp3871
    @marvintopp38712 жыл бұрын

    Cann you deutsch

  • @mikkelnielsen888
    @mikkelnielsen88810 ай бұрын

    test

  • @ignoracy
    @ignoracy Жыл бұрын

    The title is in english, why is the video in cartel?

  • @AI.MadeTechReviews

    @AI.MadeTechReviews

    Жыл бұрын

    If you have any questions I might have the answers

  • @AI.MadeTechReviews

    @AI.MadeTechReviews

    Жыл бұрын

    Greetings from Dominican Republic 🇩🇴

  • @Igor-nj5hm

    @Igor-nj5hm

    Жыл бұрын

    How you pull out the white head?

  • @AI.MadeTechReviews

    @AI.MadeTechReviews

    Жыл бұрын

    @@Igor-nj5hm with Pliers...

  • @numerologia1556
    @numerologia15562 жыл бұрын

    Terrible 😫

  • @tcheuwa
    @tcheuwa4 ай бұрын

    Vidéo inutile

  • @AI.MadeTechReviews

    @AI.MadeTechReviews

    4 ай бұрын

    Merci.

Келесі