Removing Stumps? Try this.

I attempt to burn stumps with Kerosene, potassium nitrate and charcoal. And I find out that...
Follow our adventures as we try to be farmers. Subscribe here: Kakadoodle.com/KZread
🎬 CHAPTERS
0:00 Burning stumps
⚡️ PRODUCTS IN THIS EPISODE
- Potassium Nitrate: amzn.to/3amkH4b
🎵 MUSIC IN THIS EPISODE
Music from Epidemic Sound: www.epidemicsound.com/referra...
🐓 MORE FROM KAKADOODLE
Kakadoodle.com
/ kakadoodlefarm
/ kakadoodlefarm
/ kakadoodlefarm
/ farmermarty
#treestumpremoval #byestump #stumpremoval #nature #stumplife #stump #treestump
Thanks for watching!

Пікірлер: 40

  • @rogerknights857
    @rogerknights857 Жыл бұрын

    Using a chain saw to cut the stump down close to the ground shortens the burn time needed.

  • @harleyb.birdwhisperer
    @harleyb.birdwhisperer8 ай бұрын

    I’ve done several stumps in the last couple of weeks. The best technique I’ve found uses about 10’ of 12” aluminum flashing and a Weber Kettle lid. Loop the flashing around the stump, fill with charcoal, fire it up, open the vent on the lid and put it on top. If your stump is bigger than the lid, cut it vertically to ground level with a saw (chainsaw is best), and do the halves (or quarters) one at a time. One of mine was close to a fence. The vent on the lid lets you direct the hot exhaust away from exposures.

  • @Kakadoodle

    @Kakadoodle

    7 ай бұрын

    Good idea!

  • @harleyb.birdwhisperer

    @harleyb.birdwhisperer

    7 ай бұрын

    @@Kakadoodle Yup. The key to burning stumps is to keep the heat in. The ideal for burning is bottom up, because heat wants to rise but you can’t get under a stump, and by their nature, there’s moisture you need to boil out of them, so you need to put a roof on the fire to contain that heat to do the job

  • @TheExplosiveGuy
    @TheExplosiveGuy Жыл бұрын

    You used the potassium nitrate incorrectly, the stump is supposed to be drilled with an auger instead of cut with a saw, you want to drill at least 15-20 1" to 1.5" diameter holes around the top and sides of the stump, with the holes on the sides angled downward, and make sure no holes poke out the other side. Once the holes are drilled to depth (about level with the ground, or as deep as you can get with your auger if not) you fill them with potassium nitrate, a few ounces per hole at least (I buy the stuff bulk, so I go ham and fill the holes to the brim, using about 5 pounds in one stump lol) then once each hole is filled you pour boiling water into each hole also to the brim. Wait 2 months, add more boiling water, wait 2 more months and add more KNO3+boiling water again, then after that wait another month or two to fully dry out, it's best to start the 6 month process near the beginning of the year, so when you're ready to burn it's had all summer to dry out. Once it's bone dry and you're ready to burn (covering it with a tarp or piece of plywood is a good idea if it rains a lot, but still allow airflow so it dries) you will then pour about 3-6 ounces of kerosene into each hole and let that absorb into the wood for about an hour or two, then you light it up with the steel barrel around it covered in charcoal briquettes or firewood. The stump will be a pit of ash below ground level in a couple hours, an hour if you use 10 pounds of KNO3 total like I do lol. The KNO3 stump removers need water and time to work properly, what they do is suffuse the wood with oxygen which allows it to burn much more rapidly, just pouring it on the top or in saw cuts won't do anything at all.

  • @harold1573

    @harold1573

    Ай бұрын

    If you do it right the wood smoulders like a lit cigarette all the way out to the ends of the roots. My father did it that way. I don't think you need quite so much nitrate.

  • @TheExplosiveGuy

    @TheExplosiveGuy

    Ай бұрын

    @@harold1573 Go big or go home I say!😂

  • @fionaclong
    @fionaclongАй бұрын

    I loved this video and your honesty - I came to find out how to get rid of a few stumps we have but unfortunately they are up against an ugly modern plastic fence ( not ours ) I think I’ll try the Epsom salts though. Thanks for sharing your farm life also

  • @kennethlowe6337
    @kennethlowe6337 Жыл бұрын

    Cut stump the same way. Soak with diesel build a little charcoal fire on top after a hour put a fan blowing on it. This will keep the ash off and make it burn like a blow torch.

  • @hippiehillape
    @hippiehillape2 жыл бұрын

    I was taught holes filled with saltpeter, boiling water poured over, wait a week, pour kerosene over, wait a week... Then burn it, it'll smolder for a couple days underground and get stump and roots out

  • @Kakadoodle

    @Kakadoodle

    2 жыл бұрын

    Ahh. That sounds way more efficient.

  • @yaykruser

    @yaykruser

    2 жыл бұрын

    you can also use ammonium nitrate instead of potassium nitrate and Diesel instead of kerosene... (dont try it )

  • @hippiehillape

    @hippiehillape

    2 жыл бұрын

    @@yaykruser by dude, that incredibly dangerous... And borders on criminally stupid to post .. all posters, this idiot is flirting with the recipe of a bomb... A very unstable and volatile bomb... Made most famous in the Oklahoma bombing by tim McVeigh

  • @benjaminotto8116
    @benjaminotto81162 жыл бұрын

    When it comes to burning away stumps best results are going to require work and time… the good news is time can be substituted for more work… if you have time (6 months or more) do some light digging around the most topical roots (6inches below ground level) cut a grid pattern in the stump with chainsaw use rot accelerants and dehydrants to fully kill the stump and make it susceptible to burn (might want to reapply every few weeks)then once the stump looks like firewood douse it in an accelerant (like lighter fluids to) cover it with a barrel and pour in enough charcoal to cover the stump (preferably pre lit) now if you don’t have 6+ months to kill the stump… you can accelerate the process… but you will need to trade in a descent amount of sweat equity… you going to need to dig probably a foot into the ground around the stump (till you can put your hand under a few of the topical roots (this will provide you with better air flow underneath and allow you to cut deeper into the stump with chain saw) do not apply any rot accelerator apply your barrel fill with charcoal and let it burn… you will likely find yourself losing a flame and clearing out ash (to stop it from smothering embers and coals) a few times before the stump fully burns away… Pick your poison you’ll either need patience or sweat equity

  • @Kakadoodle

    @Kakadoodle

    2 жыл бұрын

    Yep. I learned that as well. Those no easy way to do it. Other than calling somebody to remove it for you.

  • @profdleeucc

    @profdleeucc

    Жыл бұрын

    @@Kakadoodle Yes, one can use like maybe 18 inches deep directly into the top of three stump to make the grid cross hatch pattern cross cuts as deep as 18 inches deep; this is to allow not only free air flow but also so that one can douse the grid cross hatch pattern cross cuts 18 inches deep in the wood have sufficient air flow to support very hot combustion; also apply like two layers of the charcoal briquet to help keep the flame going on the tree stump; also use one of those plug in tube air blowers; as that will effectively super turbocharge the tree stump combustion rate also as well; make sure to remove the ash regularly and repeat it all over again

  • @Technoanima
    @Technoanima Жыл бұрын

    The metal trash cover was missing one piece. A lid. Basically with a lid, the heat is trapped, eventually becoming so hot, it forms a draft. Pulling air from the bottom and shooting it off the top!

  • @rogerknights857

    @rogerknights857

    Жыл бұрын

    Of course the lid needs to have a hole in it to allow a draft to exist, right?

  • @PopleBackyardFarm
    @PopleBackyardFarm3 жыл бұрын

    We just had to remove a few of our stumps and have a big one we are working on

  • @Kakadoodle

    @Kakadoodle

    3 жыл бұрын

    Ya? What did you use to get rid of them?

  • @rickjeffjeff
    @rickjeffjeff11 ай бұрын

    Dig them out.Old method,good exercise, have some fun,pick axe,pull it out.Get large ones done in half a day.Old truck or tractor

  • @jeremyking3986
    @jeremyking39869 ай бұрын

    Came for the stump removal, stayed for the rest of the farm videos

  • @Kakadoodle

    @Kakadoodle

    7 ай бұрын

    lol. Thanks for watching!

  • @stuartabbey5195
    @stuartabbey51952 жыл бұрын

    Still a good video

  • @Kakadoodle

    @Kakadoodle

    2 жыл бұрын

    Thanks 😏

  • @alanwhitsitt5196
    @alanwhitsitt5196 Жыл бұрын

    Drill hole all over the stump. Pour on your used car oil and let it soak in. Repeat until your oil is gone. Light it with some lighter fluid and let smolder until stump is gone. LOL Totally environmental friendly method!

  • @Kakadoodle

    @Kakadoodle

    Жыл бұрын

    Ha. Right!? Thanks 😊

  • @justsmitty1709
    @justsmitty17097 ай бұрын

    Ace Hardware. Stump grinder rental $45 half day.

  • @genesegal7182
    @genesegal71823 жыл бұрын

    Dude, KNO3 is designed to accelerate rot over time, and NOT to be an ignition accelerant (facepalm)

  • @patrickday4206

    @patrickday4206

    Жыл бұрын

    Potassium nitrate also allows the wood to burn but has to be absorbed in maybe some sugar if you want a stump rocket jet lol

  • @AspartameBoy
    @AspartameBoy2 жыл бұрын

    Done wrong. Drill bunches of small holes. Pour in salt peter dissolved in water. Let dry. Then light.

  • @Kakadoodle

    @Kakadoodle

    2 жыл бұрын

    Ahh. Thanks. I just bought some to try that! 👍

  • @jeffreygray9157

    @jeffreygray9157

    Жыл бұрын

    Just don't eat/drink salt Peter,, you may not like results

  • @007MegaRoll
    @007MegaRoll Жыл бұрын

    dynamite? lol

  • @Kakadoodle

    @Kakadoodle

    Жыл бұрын

    👍