Done it! Took just over an hour. Quite a fiddly job. So glad it's done.
@lyndonbell51473 ай бұрын
That is an excellent instruction video as well as visuals of the procedure. We were successful due to this video
@wallyclapa6739 Жыл бұрын
Really good video,no bs to sit through
@johnmalcolm99808 ай бұрын
True to my usual form, a simple repair became a hassle when I lost one of the ball bearings.
@ripin4x481
2 ай бұрын
Half way through the process of putting mine back together, big spring is no where to be found and missing 1 bullbearing, have taken out the ignition barrel and now it won’t go back in but it’s all ready to go 🙈
@bartnettle7 ай бұрын
Excellent Instruction!
@markbehr882 жыл бұрын
Excellent video. Thanks!
@TheHaydn1417 күн бұрын
Very helpful and professional video! Not sure about the Collingwood hat though 😆
@deveous_dave Жыл бұрын
Just finished doing my SY territory ignition. A little fiddly but quite easy.
@philsharp61205 ай бұрын
My 07 terri sy wouldnt crank when in town (ing lights on) Swapped fuses relays and found bridging start relay would crank and run. Drove home and found wiggling key in start would start it, but then key lost detents an a ball bearing fell on my foot.... looks like will have to rebuild as per this video. One other fault before total fail was fan aircon stopped working and radio turned off but I could turn on. Thanks for this video, quicker than opening workshop manual.
@benkaramaene32764 жыл бұрын
Man...how hard is it to remove push those hoising pins out and then get them back in again. If i had've known this first i wouldnt have attempted it lol
@ChrisSofos8 ай бұрын
Great video! Thanks for sharing! Any links where to find the switch extractor and the new switch parts? Thank you!!!
@ShannonHartnett-1172 жыл бұрын
Exceptional vid mate kept simple and clean very professional thank you for sharing this knowledge
@johnmalcolm9980
8 ай бұрын
True to my usual form, a simple repair became a hassle when I lost one of the ball bearings.
@charlieeden863 Жыл бұрын
Where do we get the ignition switch removal tool from?
@peterbaker380 Жыл бұрын
Just wondering where you can get the new housing from. I'm in nsw, thanks
@simonmoriarty998711 ай бұрын
Thx. Very good
@eyespy14152 жыл бұрын
Oh for the want of two allen screws instead of the pins...
@darryllspalding52112 жыл бұрын
Great video young fella! Could you recomend anyone in Darwin to do this job for me? The copper plate and stuff just fell on the floor of my ute. Cheers
@jettmtb3379
2 жыл бұрын
Same
@johnmalcolm9980
8 ай бұрын
same, nothing broken, just fell apart. Lost a ball bearing somewhere. Small thing, major hassle. Keep a magnet handy.
@johnmitchelltaus Жыл бұрын
Where can you buy the kit from and what is it called?
@kevinbyrne4404
Жыл бұрын
www.fordignitionswitch.com.au
@henryhiggins20212 жыл бұрын
I found the ignition didn't click into on and acc like the original. key now feels like turning porridge . very expensive for what you get
@larzblast
2 жыл бұрын
Then you did something wrong. I just did mine today and it feels solid.
@TheBohoushek806 ай бұрын
Anny help where can i find buy the removal tool?
@billyhutchison8737
6 ай бұрын
When you find out let me know please lol
@jedw7499 Жыл бұрын
I've tried to call to purchase phone is never answered are you guys still in business?
@wc142
Жыл бұрын
I'm not getting any response from Kev either, have they gone out of business
@jedw7499
Жыл бұрын
@@wc142 must of which is unfortunate can't find anymore DIY places to sell them
@jedw7499
Жыл бұрын
@@wc142 must of which is unfortunate can't find anymore DIY places to sell them
@markcrow92023 ай бұрын
If it was designed properly from in the first place wouldn’t have to do this shit
@larzblast2 жыл бұрын
Just did mine, in all of about 30 minutes. The removal tool is an engineering masterpiece, unlike Ford and Bosch's disgusting engineering of this switch. Definitely be sure to have nice long pin punches on hand, otherwise it will be a painful task. The rest is easy if you follow the instructions closely and take your time with it. Screw Ford for poor quality components. Makes me glad they shut down the Adelaide factory.
@josephmohi3111 ай бұрын
I just buy a spare whole wheel assembly with keys put in get coded $50
@waygu666 ай бұрын
This is not the same tool i recieved nor did the insttuctions match the tool i recieved & as theres not a sufficent flat spot on the coated alloy housing whos the genius that forgot this shit slides every fkn where
@romemancer79058 ай бұрын
What a stuff up Ford made to make what should be a simple job hard for the home mrchanic...give me an old falcon any day...taking out the barrel from the dash is a 5 minute job..BA and BF Falcons are such shitboxes ill never buy another one !!!
Пікірлер: 36
Done it! Took just over an hour. Quite a fiddly job. So glad it's done.
That is an excellent instruction video as well as visuals of the procedure. We were successful due to this video
Really good video,no bs to sit through
True to my usual form, a simple repair became a hassle when I lost one of the ball bearings.
@ripin4x481
2 ай бұрын
Half way through the process of putting mine back together, big spring is no where to be found and missing 1 bullbearing, have taken out the ignition barrel and now it won’t go back in but it’s all ready to go 🙈
Excellent Instruction!
Excellent video. Thanks!
Very helpful and professional video! Not sure about the Collingwood hat though 😆
Just finished doing my SY territory ignition. A little fiddly but quite easy.
My 07 terri sy wouldnt crank when in town (ing lights on) Swapped fuses relays and found bridging start relay would crank and run. Drove home and found wiggling key in start would start it, but then key lost detents an a ball bearing fell on my foot.... looks like will have to rebuild as per this video. One other fault before total fail was fan aircon stopped working and radio turned off but I could turn on. Thanks for this video, quicker than opening workshop manual.
Man...how hard is it to remove push those hoising pins out and then get them back in again. If i had've known this first i wouldnt have attempted it lol
Great video! Thanks for sharing! Any links where to find the switch extractor and the new switch parts? Thank you!!!
Exceptional vid mate kept simple and clean very professional thank you for sharing this knowledge
@johnmalcolm9980
8 ай бұрын
True to my usual form, a simple repair became a hassle when I lost one of the ball bearings.
Where do we get the ignition switch removal tool from?
Just wondering where you can get the new housing from. I'm in nsw, thanks
Thx. Very good
Oh for the want of two allen screws instead of the pins...
Great video young fella! Could you recomend anyone in Darwin to do this job for me? The copper plate and stuff just fell on the floor of my ute. Cheers
@jettmtb3379
2 жыл бұрын
Same
@johnmalcolm9980
8 ай бұрын
same, nothing broken, just fell apart. Lost a ball bearing somewhere. Small thing, major hassle. Keep a magnet handy.
Where can you buy the kit from and what is it called?
@kevinbyrne4404
Жыл бұрын
www.fordignitionswitch.com.au
I found the ignition didn't click into on and acc like the original. key now feels like turning porridge . very expensive for what you get
@larzblast
2 жыл бұрын
Then you did something wrong. I just did mine today and it feels solid.
Anny help where can i find buy the removal tool?
@billyhutchison8737
6 ай бұрын
When you find out let me know please lol
I've tried to call to purchase phone is never answered are you guys still in business?
@wc142
Жыл бұрын
I'm not getting any response from Kev either, have they gone out of business
@jedw7499
Жыл бұрын
@@wc142 must of which is unfortunate can't find anymore DIY places to sell them
@jedw7499
Жыл бұрын
@@wc142 must of which is unfortunate can't find anymore DIY places to sell them
If it was designed properly from in the first place wouldn’t have to do this shit
Just did mine, in all of about 30 minutes. The removal tool is an engineering masterpiece, unlike Ford and Bosch's disgusting engineering of this switch. Definitely be sure to have nice long pin punches on hand, otherwise it will be a painful task. The rest is easy if you follow the instructions closely and take your time with it. Screw Ford for poor quality components. Makes me glad they shut down the Adelaide factory.
I just buy a spare whole wheel assembly with keys put in get coded $50
This is not the same tool i recieved nor did the insttuctions match the tool i recieved & as theres not a sufficent flat spot on the coated alloy housing whos the genius that forgot this shit slides every fkn where
What a stuff up Ford made to make what should be a simple job hard for the home mrchanic...give me an old falcon any day...taking out the barrel from the dash is a 5 minute job..BA and BF Falcons are such shitboxes ill never buy another one !!!