The microphone wasn't having it today.

Looks freaky with the selfie camera driving on the other side 😁😁

Classic dude. Cool build. I appreciated your honesty with the leaking transmission pan. 😂

It’s enjoyable to watch this build coming along.

I had a carter 800 quadra jet carby on a 351 there awesome u won’t go back to 750 just more fuel cause u will want to feed it everywhere. Sick Ute what a beast well done

Hey mate that ute is getting better love ur work on the hq goes fantastic with bigger carb.👍

I had petrol fumes coming from my speakers, heaven lol...

@Joedennett69

Жыл бұрын

He he. It ticks the boxes for Sounds, Sights, and Smells.

Good stuff, mate. Nothing crazy, just tried and true upgrades

Nice,

sneaky lhd conversion too haha

@Joedennett69

Жыл бұрын

Yes the camera in selfie mode likes to mirror everything.

Hi what brand trans crossmember did u use . Was it used because exhaust clearance or u did not have one ?? Does the aftermarket give better exh clearance than factory unit ?

@Joedennett69

Жыл бұрын

I show in a previous video me removing the old crossmember (wich was a modified 6cyl one) because of a few reasons. 1 being i couldnt remove the crossmember without removing the transmisson. 2 the transmission would sit too close to the tunnel. I didnt have a problem with exhaust clearance with ethier because i built the exhaust around it. So i ended up buying a rod shop specific th400 crossmember. As the factory th400 crossmembers are usually equivalent or more expensive and hard to find.

@paulthompson1654

Жыл бұрын

@@Joedennett69 Yes I have a factory th400 with reinforcing plates vs Trimatic with out . From memory 2 different widths also . Even the collector /exh connection seems to have to duck under the X member in your ute . Do u think the x member could be higher or no more room above ??? Could your exhaust go higher to the existing aftermarket x member ??

@Joedennett69

Жыл бұрын

@@paulthompson1654 I am running block hugger headers opposed to most guys that run 4into 1 long tubes that collect behind the motor, because if this the spacing between the two pipes is very narrow so the exhaust clearancing in the cross member is irrelevant to me. I did have to put a few dents in my pipes for me to get the desired exhaust height and clear the crossmember

@paulthompson1654

Жыл бұрын

@@Joedennett69 thanks ,I went back thru older vids and checked out the clearance

What's the model for the Redbacks i got to get a one for my one tonner i have limited clearance as the muffler needs to fit under the floor

@Joedennett69

Жыл бұрын

Part number F719GP. I bought them online from the exhaust shop.

What is redback mean, is it similar to what we say in the states "redneck" ?

@DanWallis86

Жыл бұрын

The brand of exhaust mate.

@itseithergonnaworkoritaint7852

Жыл бұрын

@@DanWallis86 LOL, ok that makes more sense, we don't have that brand over here that I know of anyway.😁

@michaelmcclown5593

Жыл бұрын

@@itseithergonnaworkoritaint7852 It's also an Australian spider.

@bradmurray8573

Жыл бұрын

The American Redneck equivalent in is Australia is a Bogan.

@peaner083

6 ай бұрын

​@@bradmurray8573Well said cobba haha

Unless my eyes are playing up today hahahaha the steering wheel has been Americanised.. These Aussie legends are just built to out last everything, Hey is this a 1872 model? I drive a 76 HJ Wagon, Cheers..

@Joedennett69

Жыл бұрын

Its a 71. Phone on selfie mode mirrors everything.

You can say its a USA import hq ,left hand drive haha