THANKYOU !! this was so extremely helpful, I'm starting out at jewellery making , Ive watched hundreds of videos and your video is the best one

@JulessaScofieldMetalsmith

21 күн бұрын

Alice! Thank you for such a wonderful comment. I truly appreciate the feedback. I am working on new videos for the channel and hope to have some posted soon!

@alicekomene2460

21 күн бұрын

@@JulessaScofieldMetalsmith I can't wait!

Im boyt 3min in an im already inlove with ur teaching style ty!

@JulessaScofieldMetalsmith

2 жыл бұрын

Awww… thank you so much. I have new videos planned, just trying to get set up after the move 😃

I can agree with you on making your own tubing for stones less than 6mm because they are really hard. I make all of my own tubes for most of my stones but having a swage block and a decent hammer makes it a bit easier. Most of the time I make tubes put of D shaped wire and make jump rings out of them. Using D wire has major advantages because we all have some lying around. It gives enough thickness to set the stone and the outer diameter can give some ace effects. Just file to your preference but remember to bevel a 45 degree angle when you have the right size-you need a thin edge to rub over the stone.

@JulessaScofieldMetalsmith

3 жыл бұрын

A tubing draw plate would be good too! They’re really expensive though so I don’t have one yet. Yes! A 45 degree angle is key for the rub over.

@johnmimist

2 жыл бұрын

D wire as in D wire for rings?? I’d love to see this!! 😃

@mizzify

2 жыл бұрын

@@johnmimist yes D wire that we use for rings. I love using patterned wire and so long as the cab is snug provided you chamfer the edge to 45 degrees and file the edge so it's within 0.5-1mm from the edge it's great. It takes a fair amount of practice because you really do need to make sure the inner edge is super clean before you start pushing it or hammering it over. I tend to use chunky bezels for big cabs and pearls x

Wow, this was VERY, VERY, HELPFUL, thanks! 👍 I believe you just saved me some 💲. I saw another demo that used a ball burr 1st to start out and a setting burr 2nd. I can see how a ball burr might ensure you start out completely centered but knowing it isn't necessary is good. I'm just wanting to attempt to tube set 3mm CZ's. Also, I was stressing out over finding a single punch (instead of a set) when I already have a bezel rocker and burnisher. Now if I can only find the correct size setting burr for my 3mm stones (and maybe 2mm stones) without having to buy a complete set, I'll be good to go! 👍 Thank you again so much!🙂

@JulessaScofieldMetalsmith

2 жыл бұрын

You’re so welcome. You may be able to buy Busch burs in single sizes. They’re a little pricey, but we’ll worth the extra cost. They last a long time.

Ty so much..

@JulessaScofieldMetalsmith

3 жыл бұрын

You’re very welcome!

very good mathed to teach thnx

@JulessaScofieldMetalsmith

2 жыл бұрын

You’re very welcome! 😁

@VIJAYKUMAR-oc6ik

2 жыл бұрын

can you teach me stone rings

Would like to see a video on oval faceted gemstone setting... (;

@JulessaScofieldMetalsmith

3 жыл бұрын

I can definitely do that! Thank you for watching! 🥰

Make your own tubing.

@JulessaScofieldMetalsmith

4 ай бұрын

I definitely do that for medium or large stones, but for the smaller, 4mm and less, I buy premade tubing.

🌺

@JulessaScofieldMetalsmith

3 жыл бұрын

Thank you! 😀

Lovely video, where do you buy your faceted stones ?

@JulessaScofieldMetalsmith

2 жыл бұрын

Thank you so much! I buy from Gemselect.com or jamminggems.com usually!

Hi there. I have a 5mm by 3mm round faceted Diamond, and I want to make a bezel set men's ring band. I already have the ring made, I just need to solder on a bezel cup to fit the Diamond. I see premade bezel cups on Etsy, but not sure what size to get. I see one online that says its 6mm on the outside diameter, 4.5mm on inside diameter, and 5mm seat diameter. I already reached out to the seller to ask if it would fit my Diamond, but they are not responding. So decided to come to KZread for advice. Thank you for your time, and have a wonderful day.

@JulessaScofieldMetalsmith

3 жыл бұрын

Hi Jared! I wouldn't use a premade bezel cup since your stone is a faceted diamond. If you can, make your own tube setting or buy a premade tube that has a thick inner wall ( 0.5mm or more) and a diameter of at least 5.5mm. Then you can use a setting bur to open the seat and then burnish the walls down on top of the stone. Hope this helps!

@JulessaScofieldMetalsmith

3 жыл бұрын

If you're talking about a pre-made tube bezel, I'd say the 6mm outer diameter and 4.5mm inner should be ok. The only thing you really need to find out is the height of the pre-made tube bezel to keep the culet (bottom of the stone) from touching your finger.

I have trouble moving the prongs over because after all that drilling and cutting the metal is hardened. Any ideas to help that?

@JulessaScofieldMetalsmith

Жыл бұрын

Hello Fire!!! For prongs, you could gently anneal them, but you run the risk of un-soldering or melting them. Do you use a prong pusher or just by hand? Sometimes I'll leverage the side of my bench to get some extra force against the prongs since my hands are not always strong enough. Also, if you're talking about a bezel setting, I will take a file and thin out the top edge of the bezel very carefully before re-polishing and pushing the bezel over the stone. I generally do thicker walled bezel settings, so this method has really helped a lot. Hope these suggestions help. Let me know how it goes...

Meaning then the wall is 1 1/2mm? Half bigger than stone at least? And a full mm smaller?

@JulessaScofieldMetalsmith

2 жыл бұрын

Hi! The wall should be at minimum 1mm thick in my opinion. That gives you about 1/2mm to cut the seat for the stone. So if my stone is 6mm in diameter, I prefer the inner diameter of the tube to be at most 5 1/2mm with at least a 6 1/2 to 7mm outside diameter. Thicker walls work just as well, there is just more metal to push over the stone.

Would you recommend a tube 6.35 mm outer diameter tube for a 6 mm stone please .?

@JulessaScofieldMetalsmith

Жыл бұрын

Hello Millybells! 6.35mm would be very close for a 6mm stone. You will have very little room for error, but it can be done. However, the most important thing is that the inner diameter is about 0.50mm smaller than the diameter of the stone so there is enough of an edge to sit the culet of the stone for a stable position. I hope this helps! ☺️

@millybells

Жыл бұрын

@@JulessaScofieldMetalsmith Thank you for replying and sharing your knowledge , your videos are very inspiring and helpful to me as a student of jewellery making . I will go ahead to make this setting for my projects 🙂👍❣️

@JulessaScofieldMetalsmith

Жыл бұрын

@@millybells good luck! Let me know how it goes 😁

❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

@JulessaScofieldMetalsmith

8 ай бұрын

Thank you! 😘

You don’t use a lubricant when you use your setting bur?

@JulessaScofieldMetalsmith

2 жыл бұрын

You can. I don’t always since I’m not using the bur at high speeds. But to make them last longer a bur lube is recommended. 😁

I miss those days when silver was $7 an ounce

@JulessaScofieldMetalsmith

2 жыл бұрын

Oh man, you and me both!!!