Hello good people i edited the video to the best my abilities permit, i am a newbie so if you have any sugestions or questions i appreciate you write it in the comments, all feedback helps me making better videos for you. Thanks for watching.Have a nice one.

@scottparish9156

4 ай бұрын

Please can you let me know the size fir motor heatsink and fan and fan size for esc please as I want to get them for my one

Hi the videos are good and some great tips in there as well, have you please got a link to the fan and heatsink for both the motor and esc please. Also do you know the sizes you need please 👌

@Fast_Lane_RC

4 ай бұрын

Hi, first of all thanks for the feedback, i much apreeciate it. The motor heatsink diameter is 28mm. Link for the heatsink with fan for the motor: a.aliexpress.com/_EzVaK2d This is the wire divider if you dont want to split wires: a.aliexpress.com/_EzhjLjF And the heatsink for the motor without fan if you prefer that: a.aliexpress.com/_EQKcUAV The esc fan is a 25mm fan attached to the side of the chassis right beside the esc, with a diy steel plate that holds the fan(will make a small video showing how i did it) here is the link: a.aliexpress.com/_Evjh4sd Hope thats what you want, if you need more help please ask. Have fun.

@scottparish9156

4 ай бұрын

I thanks for the feedback and links for the bits I need, do you have a 2 wire divider or 3 wire divider for yours?, could you show a close up picture or video of how your motor fan and esc fan are connected up please 👌. I have literally watched all your videos with all the mods you have done and they are awesome mate 👍

@Fast_Lane_RC

4 ай бұрын

@scottparish9156 I have a 3 wire divider one is for the servo and the other two are for the fans, i already filmed a video about it, just have to edit and i will post it and explains all that, tomorrow i ll try and finish the editing.

@Fast_Lane_RC

4 ай бұрын

​@@scottparish9156 @scottparish9156 Just posted the video my friend, got check it out: kzread.info/dash/bejne/io2Ll5edfsLMj5M.htmlsi=vLr6e0GixdMA1XuF Sorry if you already seen the video mate, hope your doing well. See you.

@scottparish9156

4 ай бұрын

Hi mate yes saw the video the other day, good video mate thank you, keep well and happy RC ing 👍

Have you ever had any problems putting on new wheels? I got some recently and when I tighten them the car wheels won't spin after

@Fast_Lane_RC

Ай бұрын

Hello my friend, Yes if you tighten too much it makes pressure on the bearings, the solution is backout the wheel nut little by little until it moves free and use blue thread lock so it doenst come backing out.

@rarebanana

Ай бұрын

@@Fast_Lane_RC Alright thanks! A little strange because I can tighten the stock tires to its max 😵‍💫😆

@Fast_Lane_RC

Ай бұрын

@@rarebanana hello again see if the new wheel when you put the hex in it if the plastic of the wheel protrudes from the hex, cause this way it would rub against the steering cup, the cause might be that the wheel hex is 4mm and the wheel plastic hex insert might be for 5mm hex. If this is the case you have two solutions, grind it a little bit the plastic so it stays flush with hex or install a washer in between the hex and the wheel so the hex is a bit thicker. do you understand? I am just thinking of what it could be, hope it helps you in anyway. Thanks for watching.

@rarebanana

Ай бұрын

@@Fast_Lane_RC awesome thanks for the info!