Very good video. Wish all tutorials were like this. Thanks again.

@shoptimewithdrew

10 ай бұрын

Thank you!

You’re super talented Drew!!! ☺️

@shoptimewithdrew

Жыл бұрын

Thank you very much.

IM INSTALLING THE NEW 69-59210 KIT ON A 2024 TODAY AND USING THIS VIDEO FOR REFERENCE. THANKS!

@shoptimewithdrew

5 ай бұрын

Hope that the video will help you.

Thanks, now I know what bolts to check.

man that installation looks easy! good work!!!

@shoptimewithdrew

Жыл бұрын

Thank you!

@D_Jay_man

Жыл бұрын

It was pretty easy. Its nice to work on newer cars though

great video, thanks for sharing!

@shoptimewithdrew

3 ай бұрын

Thank you!

Subscribed

wish someday got install on my trd rav4🙌

@shoptimewithdrew

Жыл бұрын

It makes them look pretty good.

Hey drew, whats your thoughts on this lift would you recommend this type of lift or the other popular option of just changing out the springs? thx

@shoptimewithdrew

11 ай бұрын

I think this is a good quality lift. I think this lift will accommodate anything you would want to do in your rav 4.

Nice Video Drew! Would you mind to shared your experience with that lift kit on the rav4? It seems that there is a lot of people complaining about issues with noises and vibration at low speed or when go on the gas a little to hard from stop. Thanks!

@shoptimewithdrew

4 ай бұрын

Thank you! I have not heard of any issues with the lift. They did have an issue with bump steer in the beginning, but they updated the kit to address that issue.

@thebranndoful

3 ай бұрын

@@shoptimewithdrew This is great! Does this work on 2024 adventure/trail models?

@shoptimewithdrew

3 ай бұрын

This will fit a 2024.

Nice video. I'm not doing a big lift like that. I'm just going to put a 1-in front spacer and replace the torsion bar end links. But I would like to add a 1/2-in spacer to the rear. Do you know who makes just a 1/2-in spacer? I can probably just use a coil compressor manually pull down that coil and put the spacer in without dropping any subframe. Thank you!

@shoptimewithdrew

Ай бұрын

I'm not sure of a kit with a 1in spacer for the rear.

@DM-qe3ci

Ай бұрын

Thanks for the response. I know they're out there. I've seen them on other kits. I know Subaru has mild leveling kits. But I already did the front spacer so it's not a radical difference. It is pretty level. I just think that if I ever loaded up I might have a little tail drag. But I'm probably just going to wait until the new Bilstein terra sport shocks and struts come out for this model year. Thank you

Que medidas neumatico puedo usar al instalar éste sistema? Saludos desde Chile

exelente trabajo. nesecito un kit de levante de 2" como lo consigo.

@MsAlecs92

2 ай бұрын

Мы сможем тебе изготовить

wow that is affordable, though on the top strut in front show four bolts on lift shows 3 bolts? also toyota jersey is this toyota dealer? this can take a day or couple days to complete - where are you located

@shoptimewithdrew

9 ай бұрын

Strut has only 3 nuts that you need to take off on the top. The center nut does not get removed.

Does this have different alignment specs with the lift kit? Cuz I don’t think the hunter alignment machine gives an option for cars with lift kits.

@shoptimewithdrew

9 ай бұрын

If I remember correctly, the instructions have alignment specs, but really, there is only a front and rear toe adjustment. You can slightly adjust the camber with front shock towers.

I know it's not a popular demand but hope to see oem factory running board install. Didn't find any decent installation video on youtube.

@shoptimewithdrew

Жыл бұрын

Next time I get a set, I will make a video.

@matrix-fh9tn

Жыл бұрын

@@shoptimewithdrew Would be great for many potential Rav4 owners who have kids or elders or simply for looks. Subscribed.

@shoptimewithdrew

Жыл бұрын

Thank you!

@805spidygurl

Жыл бұрын

i just bought a 2019 rav4 i want to do this with mine. lol now to only find a trusted mechanic like you

@shoptimewithdrew

Жыл бұрын

Thank you! There are a lot of good ones out there, but like you said, you just have to find them.

Does alignment gets rid of the positive camber after installing this kit?

@shoptimewithdrew

Жыл бұрын

You will still have the same amount of adjustment for the camber as when stock hight.

My xreas crapped out on me last week, on my 4th gen runner. It took me 8 hours to change it out I’m not a mechanic though, and I didn’t have a car hoist. Just jacks and jack stands

@shoptimewithdrew

Жыл бұрын

Nice you, swap it for bilstein shocks.

@S1KRR_Rider88

Жыл бұрын

@@shoptimewithdrew unfortunately do to money constraints I had to just get some Monroe shocks. But hopefully they will at least last a year so I can save up for some better ones. I gotta do my cv axles and a front right seal, I had to change out my rear output shaft seal and companion flange seal on my transfer case also. Definitely saving money by doing the work myself this time.

@shoptimewithdrew

Жыл бұрын

Right on, you can save a lot of money doing it yourself.

@S1KRR_Rider88

Жыл бұрын

@@shoptimewithdrew less headaches getting a pro to do it though, But good things to learn and have under my belt.

Hello after installing it wheels need alignment and wheel balancing??

@shoptimewithdrew

Жыл бұрын

You will need an alignment after the lift, and if you install wheels and tires, they will need balanced.

Thanks drew, Followed your video and it took me about 5 hours with jack stands and floor jacks. Those sway bar links were tricky. I noticed that on the left front the bolts for the lower strut mount were reversed (Head and nut) is there a reason for that? Do you have the specs for the tork on the rear cradle bolts? Is the alignment completly nesasary after this install? I did not remove the tire rods. Thanks for your video it was a great guide for me. Really appriciate it.

@shoptimewithdrew

Жыл бұрын

Thanks for the comments. The front strut bolts can go in either way, but from the factory, they are facing different directions. I'm not sure the reason. For the torque, I would have to look it up. I want to say it was around 90ft lbs. I recommend an alignment because you are changing all the angles.

@MsAce0424

6 ай бұрын

How does your rav drive since install. Bought my kit. I'm installing it in a few weeks.

@D_Jay_man

6 ай бұрын

@@MsAce0424 shakes between 18 and 22 mph

I see your Toyota uniform. Are you installing this kit at the dealership? And can my local dealership install this for me too?

@shoptimewithdrew

3 ай бұрын

Yes, we installed this kit at my dealership. Your local dealership should be able to install this kit.

Where dit you put your spare tire with same size you put on your car?? It will fit on tire compartment??

@shoptimewithdrew

3 ай бұрын

We just keep the standard spare.

Miss your videos have a question 2005 Toyota sequoia limited which window motor will enter change with the hatch window motor mine is missing

@shoptimewithdrew

3 ай бұрын

Do you need the part number for the rear hatch window motor?

@billywhite8296

3 ай бұрын

Part number would be most helpful thank you

@shoptimewithdrew

3 ай бұрын

The rear window motor has been updated, and you have to buy a new back door ecu with it. New motor: 85710-0C120 ECU: 89222-0C050 REGULATOR: G9850-0C090 OLD MOTOR: 85710-0C070

@billywhite8296

3 ай бұрын

Drew again thank you so much for taking the time and looking up part number up I tried online licking it up but not very good at it obviously didn't have no luck thank you so much deeply appreciated

@shoptimewithdrew

3 ай бұрын

You're welcome. I hope to start making videos again soon. I have been doing a home addition and have been really busy.

Are these the same tires before and after? 235/55 I’m assuming? I replaced my tires before realizing I want to lift my Rav and now I’ve got buyer’s remorse 😔

@shoptimewithdrew

9 ай бұрын

They were slightly bigger. I don't remember the exact size.

Why not do 2inches one both ends?

@shoptimewithdrew

Жыл бұрын

It is a level lift that gets it setting higher and more level.

69-520 baby!

Did you change the camber bolt kit in front? what size is it??

@brienshieldon228

2 ай бұрын

What size is it??

@shoptimewithdrew

2 ай бұрын

No, I used the stock bolts, and the alignment came out fine.

@shoptimewithdrew

2 ай бұрын

You will need a 22mm socket to remove the bolt.

What running boards are those?

@shoptimewithdrew

Жыл бұрын

They are factory running boards. I think this is part number PZQ44-42121.

@subpar_singletrack

Жыл бұрын

@@shoptimewithdrew thanks!

It’s easy if you know what your doing otherwise you create your own train wreck,😮all parts torque to ;specs)

@shoptimewithdrew

Жыл бұрын

It's definitely not a first-time DIY project.

How much it is for the kit and installation?

@shoptimewithdrew

Жыл бұрын

If you run it through a dealer, you are looking at 1,500 to 2,000 installed. I have an amazon link in the description for the kit. Then you could install it yourself or have help from a friend and save some money.

What does that lift kit cost ? Excluding labor.

@shoptimewithdrew

Жыл бұрын

If you go to the Amazon link in the description, it is on sale right now.

When on dead stop and accelerate 18mph to 28mph i experience shimmy or vibration any one knows or suggestions what was the problem??

@shoptimewithdrew

10 ай бұрын

What kind of car?

@brienshieldon228

10 ай бұрын

@@shoptimewithdrew rav4 2020 XLE AWD

@shoptimewithdrew

10 ай бұрын

I looked and didn't see any common issues for a rav 4 vibration at lower speeds. If you are doing a normal driving slow acceleration, it is possibly a torque converter shudder. Torque converter shudders are usually felt at normal acceleration between 18mph and 35mph. If there is an issue.

@6u66a

7 ай бұрын

Did you ever figure this out..mine is currently doing this

@MsAce0424

7 ай бұрын

Did the original struts have cam bolts? I also have a 21 XLE. I just bought these. Im grabbing cam bolts in case the rav doesn't have them. Once you lift 2 in up.. it angles things. Cam needs adjusted along with the caster and toe. I've had toyotas in the past that could only adjust toe and caster. If i wanted to fix camber, i needed the cam kit. Just like dude who lower cars and their cam sets the upper part of the tire in.. rasing it does the opposite. Might be just enough out. I guess i will find out myself and i of course will have it aligned. Im hearing 50/50 about vibration on ALL lift kits with the 5th gen. The only thing making sense is either people arent aligning them, getting longer stab links or getting cam bolt if there arent any.

I wish the spacers were alloy aluminum as opposed to plastic

@MsAlecs92

2 ай бұрын

У нас есть лифт комплект из алюминиевого сплава

@user-qv6nm3ux8z

2 ай бұрын

That’s why a spring change may be all I need every lift kit I’ve seen so far for the RAV 4 XLE hybrid all the kits have plastic spacers if you can’t get with aluminum iam just changing to slightly bigger springs just so I can get a 2 and half inch lift

I can't stand videos like this. Take the annoying BS music off and show what you're doing WHILE you're doing it and instruct as you're doing it instead of that speeding up crap.