These should be made from the factory and made road legal like the dual sport motorcycles

@collinsatv4071

Жыл бұрын

Absolutely, imagine seeing a raptor cruising down the freeway. Great idea

@mrgmc6314

Жыл бұрын

They have reverse trikes and sling shots so why not quads right ???

@levischimann2725

Жыл бұрын

@@mrgmc6314 they do in Europe, lots of people do R1 swaps on their raptors and ride on the autobahn in Germany. Quads are street legal in most of Europe.

@pastathemechanic7536

Жыл бұрын

Anything can be road legal with modification

@pastathemechanic7536

Жыл бұрын

@@levischimann2725 Puerto Rico too

Your 600cc kart was getting a workout, big hit with the Cboys! Vasily you collabed well with the crew, your easy-going hard-working nature and dedicated experience definitely payed off. Keep up the good work👏

@VasilyBuilds

Жыл бұрын

Thank you! Im glad

@D-Kat270

Жыл бұрын

They are looking for a full time guy 🤔

@jordykellogg5568

Жыл бұрын

Check the wiring to clutch switch / neutral circuit if theyre not bypassed correctly it can change the rev limit and fuel/ignition map.

@gpmjamal9507

Жыл бұрын

@@VasilyBuilds I have a raptor r1 2011 it’s your air flow

That thing will be sick once you get the tuning sorted out 👍🏽

I'm pretty sure it'll be because of the raptor fuel pump. It needs the R6 one. Other issues could include the airbox delete and the short mufflers which might be leaning out the bike past the ECU's closed loop parameters. ECU might not have the capability to adjust to that extreme, especially if its -10 out. They adjust to cold climates etc.

@FoleyT9X

Жыл бұрын

Yes, fuel pumps are very finicky. I put an 07 GSXR 1000 engine in my 03 GSXR 1000 and it ran like shit til I put the 07 fuel pump in the tank!

@7795Dakota

Жыл бұрын

Definitely something to do with fueling due to it not reving out under load.

@bikelifebodie4138

Жыл бұрын

I had the same problem wouldn’t rev up properly and all it was was a electrical problem sorted that and it’s runs mint

@SargentGiraffe

10 ай бұрын

Do you also think that it could have something to do with the bike being launched into the air and banging the limiter the whole time?

@slon9120

10 ай бұрын

@@SargentGiraffe Nah. they're designed for high rpm. Engine was fine

What I love about it is you're able to keep all the stock plastics and gas tank I see a lot of guys swapping out for whatever bike they got the motor out of gas because the frames hacked up to fit the motor on top instead of underneath.

Airboxes are very important with motorcycles. As soon as you remove the stock airbox, you absolutely require re- jetting, or tuning on fuel injection models! I've had this same issue many times!

@magee16749

Жыл бұрын

Fuel Injected motorcycle don't use “ jets” they use Injectors instead. Hence the name. And its got a computer that will know if something changed and adjust the fuel and air mixture automatically or might have to plug it into a laptop or PC and change the tune on it. Jets are in carburetors and the number one reason why ppl switch to fuel injection is to get away from messing with jets. A fuel injector is kind like a jet but it's able to adjust how much fuel it spray's by what tune is installed on the computer.

@m3mobilealex341

Жыл бұрын

@@magee16749hence why he said or tuning for the computer module for the injector

@pauliewalnuts240

Жыл бұрын

I dont think deleting the airbox would cause this issue. The bike has a limited range of parameters to compensate for different climates. Even if it was lean it should still rev out. I didnt pay close attention but I'd say it's the exhaust being too short/not having an 02 sensor. The bike limits rpm as a safety because it cant accurately calculate air to fuel ratios.

@jpesicka999

Жыл бұрын

@@magee16749 they clearly know that. That's why they said or depending on if you had a carb or fuel injection.

@buildzmodz3871

Жыл бұрын

@@magee16749 he literally said that lol

It is 100% a bad fuel pump not letting it hit the top of the power band boys! Maybe I could make a trip up there to rip this thing sometime! Awesome job on the build!

So pumped to see this colab! Been watching both channels for years now, nice work 👍

It's the Raptor fuel pump, it's not enough to feed the R1 fuel injectors. Looks good !

@Ronin8451

Жыл бұрын

That is if it's a 2003 or later.

The problem is the raptor 700 fuel system trying to pump the r6

@nickk5368

Жыл бұрын

My thought to

@mylescotter5878

Жыл бұрын

Yes for sure swap the r6 fuel pump in and will run right

@RacerX400600

Жыл бұрын

👆🏻 This right here. I can't imagine the raptor fuel pump is sufficient for an R6.

@justinwebster7761

Жыл бұрын

I was thinking it wasn't getting enough fuel also most street bike swaps are fucked cause of not using the proper fuel pump

@xr8xproductions588

Жыл бұрын

I definitely was thinking not enough fuel

Love how chill you are , Even the cboys gott chilled with you❤️ Man u got some superpowers.

That’s badass, only thing I would’ve done differently is made the exhaust a little longer and angled them down facing the rear tires.

@coreyriggsby435

Жыл бұрын

Needs a full exhaust to a regular muffler

@chadmcdougall2536

Жыл бұрын

Yup

Really cool to see you work together with cboys

This is dope man!

Super stoked to have my 2 favorite KZread channels working together

You are one of the best builders on youtube among with Ethan from Grindhard! Keep it going champ!

@VasilyBuilds

Жыл бұрын

Thanks 🙏🏼

@p9raceway759

Жыл бұрын

@@VasilyBuilds Collab with GHPCO ?

Sooooooo sick I can’t believe I found you years ago and you’re still going hard.🔥🔥

After they sent it to space they are having troubles starting it lol I wonder why 😆🤣

Yesssss! I saw cboys talking about it and I'm lucky I found your video because I watch you too. Greatest Collab to ever come to KZread. Can't wait for them to destro... I mean use it 😂

loved the colab with cboys!

Dude I’m so happy with the collab cause you deserve to have well over a million subs. I think you should rent a shop to do your builds in

Great build Vasily from the 600cc to the R6 700cc.

I really enjoyed watching you on this project. Thanks for coming to CBoys Headquarters. Sorry you got stuck in a snow storm Vasily 👍🏻👍🏻👍🏻

@ugwud

Жыл бұрын

Thanks for watching and commenting Inbox 📥 me above to claim your Christmas 🎄 Reward Cheer's!🎉

Thank you for your awesome work with the CBoys. Earned yourself a sub, you helped them so much!

@ugwud

Жыл бұрын

Thanks for watching and commenting Inbox 📥 me above to claim your Christmas 🎄 Reward Cheers!🎉

insane build and dope collab, hope to see this thing get sorted out and running nice, and hope to see yall together in another vid soon, you definitely gotta go back out once the quad is sorted out

@ugwud

Жыл бұрын

Thanks for watching and commenting Inbox 📥 me above to claim your Christmas 🎄 Reward Cheers! 🎉

Found your videos because of the CBoys videos. You do amazing work, very impressive, keep it up!

@ugwud

Жыл бұрын

Thanks for watching and commenting Inbox 📥 me above to claim your Christmas 🎄 Reward Cheers!🎉

GREAT VIDSKI BOI MERRY XMAS

Sweet build! Hope yall can get it tuned properly!

Wild! good job man

It sounded like it was lean and wouldn't rev out under load. It could be a missing a sensor or just needs to be tuned since it now has a short exhaust providing less scavenging and more flow, but I doubt it since EFI is very forgiving in my experience. Maybe test for intake leaks on the throttle bodies and make sure someone didn't cap off a hose they shouldn't? You could also check if it has any codes, it will likely have a couple from things that were removed. California bike's often have extra stuff that can cause problems, like the air injection/PAIR system that could cause this if not capped off properly. Maybe also check that you are getting enough fuel, it looks like you swapped tanks and the pump is usually in the tank. I'm not sure that pump is enough for those injectors. Get a power commander, plug in a laptop, and you should be able to add fuel where it falls flat until it improves. It will also tell you if your TPS sensor is working properly. If it surges, give less fuel there. I've usually been able to get bikes running decent with street tuning, but it will never be perfect without an o2 sensor and a log or rolling road. There should be a tune that you can download to have a better starting point. It looks like it may already has a piggyback tuner under the seat? Be sure to update the firmware.

@bryduhbikeguy

Жыл бұрын

I agree about the fuel pump not equaling the flow needed.That and the sensors in the exhaust will cause tune default settings.I wondered about Fluid Level sensors too as the engine's leaned forward further.

@Josh-ev2xj

Жыл бұрын

@@Goatee_yay no its efi

@jth_printed_designs

Жыл бұрын

Stock raptor is 47 hp, r6 is over double that. The factory engineers are not going to use a 100hp capable fuel pump on a 47hp machine, they’ll use something like 70hp capable so it’s not running at maximum effort all the time. I would start by installing a fuel pressure sensor in the rail and logging that data, most likely going to see a pressure drop when it chokes out.

This is just like cars and cameras' honduki. Awesome

Thanks for showing us the cboys new quad 💪🏼

I can’t wait for the Cboys to bring this thing out

I can already see you hitting a mill subs, keep it up love the content man

LOVE THIS!! ❤️

WHat a clean swap, every backyard mechanic literally drooled on that.

@VasilyBuilds

Жыл бұрын

Thanks!

glad you're finally getting the recognition you deserve bro!

I’ve been waiting for this one

Ryan’s been waiting so long for this

Dude your the best builder on the net….. and I really mean it…. Your a prodigy….. never give up on anything…. Thanks for posting your outstanding videos…… you ROCK….

Great work guys. This thing looks awesome and sounds great. Hopefully you can get it. Tuned and running right can’t wait to see where it goes. Great video and great work. Good luck.👍🏼🤩❤️

@ugwud

Жыл бұрын

Thanks for watching and commenting Inbox 📥 me above to claim your Christmas 🎄 Reward Cheers!🎉

I love seeing the KZread stars get togethers. yes I said stars. to me you just reg people that are kinda famous in my eyes. Keep videos coming

Yoo @CboysTV I’ve always wanted one of them , nice build Vasily

i’ve been waiting for this vid on there channel

Insane build for the Cboys u killed it with this one bro 😎

@FarmerFpv

Жыл бұрын

He's going to end up going home with pierced nipples. 😂😂

@leonctvbikelife6086

Жыл бұрын

@@FarmerFpv 😂😂

This is your best video yet, by FARRRRRRRRRR !

@ugwud

Жыл бұрын

Thanks for watching and commenting Inbox 📥 me above to claim your Christmas 🎄 Reward Cheer's! 🎉

its definetly because of that exhaust, you need a certain amount of back pressure in the system for capturing unburnt fuel to then burn

@SupSecSquirrel

Жыл бұрын

oh yeah I agree. only way to straight pipe it would be to change the timing or cams or something....

@Toxic_gixxer

Жыл бұрын

No that wouldn’t do it lmao

@298FAB

Жыл бұрын

No just no feel free to Google actually factual information but scavenging was made redundant and obsolete only used for emissions regulations and or 2 stroke engibes etc at best if at all to what your referring the tern back pressure would be bad for an engine .....

@erik120719

Жыл бұрын

@@298FAB I argue that all the time...old flathead and shit may need it but newer engines dont need back pressure, i teter on scavenging as my seat of pant dyno can feel the difference with a crossiver pipe vs no crossover but thats not factual deduction

@298FAB

Жыл бұрын

@erik120719 I've contracted in both Aston Martin laguna building prototypes several years ago and Bentley working on the w12 engines mostly automation nowadays but several engines in my living room being rebuilt polished ported skimmed valve seats grinding compression increases etc etc just some people talk nobesense without using their brains backpressure would increase load upon everything nobody increases load where they dont have too that's where advancing and retarding the spark helps for starting big singles on bikes quads etc

Good shizz mane !💯

@ugwud

Жыл бұрын

Thanks for watching and commenting Inbox 📥 me above to claim your Christmas 🎄 Reward Cheer's! 🎉

Great content Merry Christmas

That's why it's amazing I can't believe you guys made it work

@ugwud

Жыл бұрын

Thanks for watching and commenting Inbox 📥 me above to claim your Christmas 🎄 Reward Cheers! 🎉

❤❤❤❤ Good Work! Want to see more!

That was sick!

one day i hope to live a life like yours, your projects just amaze me. makes me wonder whats in store for future

unreal collab

The next cboys video gonna be lit

What a great collaboration bro 👏 👌 I'm a day 1 sub 😀 and you've improved on every build my guy 💯 Big props from Tulsa Oklahoma 👊

Bro Ryan’s quad is a beast now

Great build!

It sounded like an ignition issue for sure. Maybe a bad coil? Check the temperature of each exhaust pipe just after where it exits the engine and make sure your not losing fire in a cylinder. Also could be a float if the engine is tipped at all. Might need to clock the carbs somehow to get the bowls to fill properly? Just spitballing... Kick Azz Build!! Going to look up CBOYS and sub!

Hell yeah R6 swapped quad now you got me going I gotta build 1 now

That sounds very good!

Great work !

Sick collab!

@ugwud

Жыл бұрын

Let chat ⤴️

Thanks for making this. I can never find videos showing the frame work to get these sport bike engines in quads.

Merry Christmas and a Happy New Year...

Good job young men!!!

Nice!! 😊

Had to come and comment on this after watching this and the cboystv version

Digital dash should've thrown a code if problem occurred. Sure it's figured out by now. Sweet adventure man!

Damn you people are crazy Btw it sounds soo damn good

Don’t know if I wanna watch this before the boys video comes out.. screw it im watching it 😂

It sounds rowdy 😂😂😂 amazing build

hell yeah man that's bad ass 😎

Sweet build

That would be a monster and I'd love to see what happens w/ it.... That would be an awesome quad to make a Grind Hard style Power wheels out of. 😉😁

I had a bike bogging on me yesterday just because the connection on the ignition coil wasn't tight enough. I checked the intake, carb, fuel and compression.. just not strong enough spark. Can't wait to see the 2T-R6!

I had a the same exact year model r6. Had the same problem it wouldn’t go over 10k majority of the time. Changed spark plugs and it completely fixed the problem.

Back pressure possibly from the exhaust.

killing it bro fuck yeah 🤪

Super clean beautiful job. Hopefully a good tuner can get ahold of it

@ugwud

Жыл бұрын

Thanks for watching and commenting Inbox 📥 me above to claim your Christmas 🎄 Reward Cheers! 🎉

this is the new c boys quad they were talking abt

Sent to space is an understatement!

I think it is the exhaust , there is reasons that they design the headers the way they do , and by running two cylinders together out each side instead of all four into a collector and then out , I'm thinking that there is NO Back Pressure at all or very little and it is really throwing everything off and not allowing the engine to Rev like it normally would . This is my thoughts on it , but really cool that you guys swapped it 👍 But my money is on the Exhaust being your major problem .

@aztommy1687

Жыл бұрын

I built zoomies about 10” long on a cbr1000rr just to get it running and it wouldn’t rev and had no top end power, even stumbled on the bottom, finished the exhaust out under the rear fender and ran amazing. I agree with you from experience.

A 2 stroke swapped r6 sounds so cool 😂😂😂 definitely do that

I find it weird you don’t see this more, Honda 250L with a 500 in it would be wicked, anyway love this it’s great to see 🤘🤘

Love the cboys

You are a beast 💪🏼 I would change the exhaust

@ugwud

Жыл бұрын

Thanks for watching and commenting Inbox 📥 me above to claim your Christmas 🎄 Reward Cheers! 🎉

no boundaries boys. nbb new channel ideas

that thing is sick

good job

Thanks for the cloud spoiler haha

For something they that they said didn't matter if it was to nice, you did a really nice job considering

Excelent x 100 !

Ya that’s why I didn’t use their welder either, glad I brought my own with me when I was there!

When I did my r1 raptor build I had to flash tune the ECU with a track tune. It gets rid of all the emissions controls that were deleted in the build. It also helps the ECU cope with some of the sensors being gone. There were also sensors that I had to buy a sensor delete device. It tricks the computer into thinking the sensor is still there but it's not.

So cool

It'll be fine and Fun too.Merry Christmas to All.

Once it's dyno tuned it'll be amazing I had to have mine tuned in order for it to run right

2 stroke R6 would be nasty!

Looks like it was fun.