Admire your work ethic, and u did a good job,but you can actually just support the upper end of the cylinder, take out the upper pin, loosen the cylinder gland, and just bump the lever for that cylinder until the shaft and packing just pops out, replace the packings and reinstall, leaving the cylinder tube on the tractor, loosen lines to prevent air lock, when reinstalling. Hope this will help on the next one! 😊
@davefontes85325 жыл бұрын
Just an FYI. Being that the hydraulic lines are disconnected, you can use a bar, or pipe to move the piston rod in or out. After you had the cylinder end pin in, you could have moved the rod end around with a pipe or bar through one of the pin bores. A 30" "sleever bar" works really good on stuff like this. It has a taper point on one end, and a pry bar on the other end. Love the videos.
@jot0178 жыл бұрын
LOL perfect response about your footwear. Sweet truck too man!
@GrassWarz
6 жыл бұрын
jot017 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@railroadman578 жыл бұрын
Chris nice job you made that look easy !!
@TomBrueggen8 жыл бұрын
That keeper pin that you made is also there to keep the big pin from spinning when you go to torque the bolt/washer. More importantly keep it from spinning when you go to break it loose in a few years. Mine on the haul truck was so warn/wallered out that I had to keep pressure on the pin with the hyrdaulics just to break the bolt loose, then relieve the pressure so I could slide the pin out.
@GrassWarz
6 жыл бұрын
Tom Brueggen subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hancockautomotive1
5 жыл бұрын
@Mr.Dozer D6N2 Get bent.
@nohomenomad14274 жыл бұрын
Glad to see you put you damn boots on!
@jamjames19718 жыл бұрын
you seem like such a nice guy and I enjoy your Videos
@jakeschisler75258 жыл бұрын
Good job, Chris!
@GrassWarz
6 жыл бұрын
Jake Schisler subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@geo_walters8 жыл бұрын
LOL! Safety first!
@robertjackson88268 жыл бұрын
I'm proud of you really good job have a good day
@FishFind30008 жыл бұрын
One thing you can get for your pickup is a soft open shock. It's like 30$ on Amazon and I got one on my truck so it doesn't slam down anymore, makes it really nice to use pull the handle and walk away.
@GrassWarz
6 жыл бұрын
FishFind3000 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@jimcunniff68594 жыл бұрын
Nice to have a spare mini .best channel on u tube right here. amazes me how you amassed so much knowledge in just your short years. I know your pain been under many machines myself. I enjoy your farm videos as well.
@janvandenbos70858 жыл бұрын
Very nice job Chris ad good as new awesome 👍👌✌
@GrassWarz
6 жыл бұрын
Jan van den Bos subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@johnm62794 жыл бұрын
It is Amazing how petty people are and how quick they are to Judge and Criticize someone for what they wear or how they do something.....Here is how you Deal with People like that you Shut the Front Door and tell them to go Else where and Don’t worry about them God will Judge them for all there Life long Nit Picking on Others and Hopefully he will Slam the Gate in there FACE.......🤘🏻🤘🏻😁😁 Good Work Chris and God Bless You and Your Friends and Family. Great Content better than any TV show.
@johnm.evangelis6938 жыл бұрын
Good job Chris, you're a Jack of all trades...
@GrassWarz
6 жыл бұрын
John M. Evangelis subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@w0560075688 жыл бұрын
Looks a good job well done.
@GrassWarz
6 жыл бұрын
Dan Whiteford subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@DyrewulfNV5 жыл бұрын
LOL! The boots :)
@jayroye70794 жыл бұрын
The little pin is designed to keep the big pin stationary so when you grease the grease goes all the way around the pin so it does not wear out as fast as the old ones did
@Builder996 жыл бұрын
you have to love the boy...nice shoes...
@GrassWarz
6 жыл бұрын
Builder99 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@KirtH273 жыл бұрын
Thats impressive installing that cylinder without working words or you did some editing
@FergusonTO308 жыл бұрын
Most excellent footwear!
@GrassWarz
6 жыл бұрын
1952 Ferguson TO30 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@frostgfx5 жыл бұрын
All we need now is a video of the Case repair person showing how a cylinder is repacked...
@kirk4673 жыл бұрын
I can’t stand video critics! Good job brother!👌🏻👍🏻👍🏻
@RRRIBEYE8 жыл бұрын
Good to see you got those fancy-dancy work boots on vs. the Jesus Creepers, lmao. But like you said - drop that cylinder on either and yer foot's fk'd either way, heh heh. Nice job.
@GrassWarz
6 жыл бұрын
Mike .R. subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@colinspencer61878 жыл бұрын
0:50 lol couldn't agree more
@GrassWarz
6 жыл бұрын
Colin Spencer subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@citrusfarmer8 жыл бұрын
shot out like a cannon. lol too funny
@GrassWarz
6 жыл бұрын
Pierre Roberge subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@regsparkes65078 жыл бұрын
Good to see those safety boots ! Did you remember to grease those pins up again ? Good job, except for 'Numb Nuts' who didn't phone you when the job was done, but he got his paycheck on time didn't he?
@canvids18 жыл бұрын
Chris You would make things easier using the gopro then would have both hands free. great put together and back working.
@GrassWarz
6 жыл бұрын
canvids1 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hancockautomotive1
5 жыл бұрын
@Mr.Dozer D6N2 Get bent.
@GITRDUG278 жыл бұрын
Is your backhoe Deere controls and link belt cat controls? That's gotta be aggravating
@joetiller10318 жыл бұрын
Good job that could be a finger pincher'
@raymondaston47968 жыл бұрын
working mans job never done
@LoggerWade8 жыл бұрын
Make shore and put your boots on driver!!! You mechanic about like I do
@cattleranch24626 жыл бұрын
What did it cost you to have your cylinder repaired? I have the exact same problem with my machine.
@GrassWarz
6 жыл бұрын
Cattle Ranch subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hancockautomotive1
5 жыл бұрын
@Mr.Dozer D6N2 Get bent.
@kikomura52478 жыл бұрын
what type of video camera are you using?
@GrassWarz
6 жыл бұрын
Kiko Mura subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@David-ll8bt7 жыл бұрын
You kind of sound like Roy D. Mercer. You know Roy Damn Mercer.
@GrassWarz
6 жыл бұрын
Deacon subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@jackbelk85273 жыл бұрын
The last time I sat my camera on an excavator track I drove off and left it. Salvaged the chip, though.
@atomicdeath108 жыл бұрын
Did he say Jesus Creepers?
@davidlagle93797 жыл бұрын
Chris, at 5:16 on video #1, you pulled the missing pin out and walked to the cab. You turned around and walked to the stick cylinder and grabbed a hammer. With one hand on camera, you had to set it (pin) down to pick up your hammer. One of those two places, brother check em out, you may find it.
@GrassWarz
6 жыл бұрын
David Lagle subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hancockautomotive1
5 жыл бұрын
@Mr.Dozer D6N2 Get bent.
@johnlim1236 жыл бұрын
you never mention what costs ...
@LoggerWade8 жыл бұрын
Hey I think it's done
@GrassWarz
6 жыл бұрын
Logger Wade subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hancockautomotive1
5 жыл бұрын
@Mr.Dozer D6N2 Get bent.
@farmall518 жыл бұрын
ha-ha who did you have pack it . lol
@Eggsr2bcrushed
8 жыл бұрын
I think he said the case dealer
@126adamski
8 жыл бұрын
How is repacking a cylinder so amusing ?!?!?
@GrassWarz
6 жыл бұрын
farmall51 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@laythg8 жыл бұрын
We're really just afraid of your toes, Chris!
@GrassWarz
6 жыл бұрын
Layth Grangaard subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@BenKempa8 жыл бұрын
I like the flip flops better
@GrassWarz
6 жыл бұрын
Ben Kempa subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@simeonperu72695 жыл бұрын
I like how your using the biggest machine on your property to fix the smallest piece of equipment 😂😂😂
@barryedwards13366 жыл бұрын
First let me say I'm from the UK so when I say this guy is a cowboy, it is not anything like or to do with what is a USA cowboy who I respect for there hard life they live, in the UK that term means he is a person who has little to none of any good sense and working practices, for instance his choice of tools, many of which were too light or wrong for the job in hand, in the 1st video. Come on! wearing open toed sandals whilst working on removing heavy items, this is an injury waiting to happen, safe working practices I think not, then the parts he removed, has he never heard of cleaning the parts, and keeping them all together in a safe place ready for reinstalling, instead of leaving them scattered around, no wonder he lost one of the pin lock rods, and to replace it with an under sized threaded soft piece of metal cut from a bolt is beyond belief ( the original locking rod is most likely made from high tensile steel), then he reassembles everything without cleaning anything some of the parts are in a filthy condition covered in muck, grit and grass, a recipe to disaster that will cause wear on those all important joints, getting the cylinder and ram repaired will have cost him a pretty penny I bet, all wasted, because this cowboy messes the job up with his poor working standards and practices, instead of doing it properly. You think I’m being harsh on him, yes I am I would hate to think this guy was doing any work for anybody else and getting paid for it, now that he has shown his standard of work practices on here.
@GrassWarz
6 жыл бұрын
barry edwards subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hunterbennett5316
5 жыл бұрын
This is a realistic repair, you could pay a dealer mechanic $2500 and you’ll get the same repair done the same way. You’re talking like these are precision instruments, they aren’t. These machines are ran in abusive, dusty and muddy conditions, usually not greased often, and don’t have .0001” tolerances. Besides it’s his equipment, he should be able to repair it how he likes without people bashing him because they’d do it differently, if you own a piece of equipment then you repair it how you feel is acceptable.
@chuckvenable61834 жыл бұрын
You sure don't believe in cleaning up your pins and regreasing the pins, little dirt to go with seals! never hurt anything Right!
@paulthompson38778 жыл бұрын
have you ever thought about buying a camera called a gopro ? then you wont have to hold your camera,the gopro sits on your cap .
@GrassWarz
6 жыл бұрын
paul thompson subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@chrismontgomery15215 жыл бұрын
I like watching you work the excavator, but your language is a little rough
@morgansword4 жыл бұрын
Pins and women have a lot in common. The older they get the loser they damn well are... pins wore out and the holes are getting sloppy
@clintonemmert51845 жыл бұрын
Man you have good videos, but can do without the bad mouth and words comes sometimes. 🇺🇸🇺🇸🇺🇸
Пікірлер: 87
Admire your work ethic, and u did a good job,but you can actually just support the upper end of the cylinder, take out the upper pin, loosen the cylinder gland, and just bump the lever for that cylinder until the shaft and packing just pops out, replace the packings and reinstall, leaving the cylinder tube on the tractor, loosen lines to prevent air lock, when reinstalling. Hope this will help on the next one! 😊
Just an FYI. Being that the hydraulic lines are disconnected, you can use a bar, or pipe to move the piston rod in or out. After you had the cylinder end pin in, you could have moved the rod end around with a pipe or bar through one of the pin bores. A 30" "sleever bar" works really good on stuff like this. It has a taper point on one end, and a pry bar on the other end. Love the videos.
LOL perfect response about your footwear. Sweet truck too man!
@GrassWarz
6 жыл бұрын
jot017 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
Chris nice job you made that look easy !!
That keeper pin that you made is also there to keep the big pin from spinning when you go to torque the bolt/washer. More importantly keep it from spinning when you go to break it loose in a few years. Mine on the haul truck was so warn/wallered out that I had to keep pressure on the pin with the hyrdaulics just to break the bolt loose, then relieve the pressure so I could slide the pin out.
@GrassWarz
6 жыл бұрын
Tom Brueggen subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hancockautomotive1
5 жыл бұрын
@Mr.Dozer D6N2 Get bent.
Glad to see you put you damn boots on!
you seem like such a nice guy and I enjoy your Videos
Good job, Chris!
@GrassWarz
6 жыл бұрын
Jake Schisler subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
LOL! Safety first!
I'm proud of you really good job have a good day
One thing you can get for your pickup is a soft open shock. It's like 30$ on Amazon and I got one on my truck so it doesn't slam down anymore, makes it really nice to use pull the handle and walk away.
@GrassWarz
6 жыл бұрын
FishFind3000 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
Nice to have a spare mini .best channel on u tube right here. amazes me how you amassed so much knowledge in just your short years. I know your pain been under many machines myself. I enjoy your farm videos as well.
Very nice job Chris ad good as new awesome 👍👌✌
@GrassWarz
6 жыл бұрын
Jan van den Bos subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
It is Amazing how petty people are and how quick they are to Judge and Criticize someone for what they wear or how they do something.....Here is how you Deal with People like that you Shut the Front Door and tell them to go Else where and Don’t worry about them God will Judge them for all there Life long Nit Picking on Others and Hopefully he will Slam the Gate in there FACE.......🤘🏻🤘🏻😁😁 Good Work Chris and God Bless You and Your Friends and Family. Great Content better than any TV show.
Good job Chris, you're a Jack of all trades...
@GrassWarz
6 жыл бұрын
John M. Evangelis subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
Looks a good job well done.
@GrassWarz
6 жыл бұрын
Dan Whiteford subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
LOL! The boots :)
The little pin is designed to keep the big pin stationary so when you grease the grease goes all the way around the pin so it does not wear out as fast as the old ones did
you have to love the boy...nice shoes...
@GrassWarz
6 жыл бұрын
Builder99 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
Thats impressive installing that cylinder without working words or you did some editing
Most excellent footwear!
@GrassWarz
6 жыл бұрын
1952 Ferguson TO30 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
All we need now is a video of the Case repair person showing how a cylinder is repacked...
I can’t stand video critics! Good job brother!👌🏻👍🏻👍🏻
Good to see you got those fancy-dancy work boots on vs. the Jesus Creepers, lmao. But like you said - drop that cylinder on either and yer foot's fk'd either way, heh heh. Nice job.
@GrassWarz
6 жыл бұрын
Mike .R. subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
0:50 lol couldn't agree more
@GrassWarz
6 жыл бұрын
Colin Spencer subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
shot out like a cannon. lol too funny
@GrassWarz
6 жыл бұрын
Pierre Roberge subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
Good to see those safety boots ! Did you remember to grease those pins up again ? Good job, except for 'Numb Nuts' who didn't phone you when the job was done, but he got his paycheck on time didn't he?
Chris You would make things easier using the gopro then would have both hands free. great put together and back working.
@GrassWarz
6 жыл бұрын
canvids1 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hancockautomotive1
5 жыл бұрын
@Mr.Dozer D6N2 Get bent.
Is your backhoe Deere controls and link belt cat controls? That's gotta be aggravating
Good job that could be a finger pincher'
working mans job never done
Make shore and put your boots on driver!!! You mechanic about like I do
What did it cost you to have your cylinder repaired? I have the exact same problem with my machine.
@GrassWarz
6 жыл бұрын
Cattle Ranch subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hancockautomotive1
5 жыл бұрын
@Mr.Dozer D6N2 Get bent.
what type of video camera are you using?
@GrassWarz
6 жыл бұрын
Kiko Mura subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
You kind of sound like Roy D. Mercer. You know Roy Damn Mercer.
@GrassWarz
6 жыл бұрын
Deacon subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
The last time I sat my camera on an excavator track I drove off and left it. Salvaged the chip, though.
Did he say Jesus Creepers?
Chris, at 5:16 on video #1, you pulled the missing pin out and walked to the cab. You turned around and walked to the stick cylinder and grabbed a hammer. With one hand on camera, you had to set it (pin) down to pick up your hammer. One of those two places, brother check em out, you may find it.
@GrassWarz
6 жыл бұрын
David Lagle subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hancockautomotive1
5 жыл бұрын
@Mr.Dozer D6N2 Get bent.
you never mention what costs ...
Hey I think it's done
@GrassWarz
6 жыл бұрын
Logger Wade subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hancockautomotive1
5 жыл бұрын
@Mr.Dozer D6N2 Get bent.
ha-ha who did you have pack it . lol
@Eggsr2bcrushed
8 жыл бұрын
I think he said the case dealer
@126adamski
8 жыл бұрын
How is repacking a cylinder so amusing ?!?!?
@GrassWarz
6 жыл бұрын
farmall51 subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
We're really just afraid of your toes, Chris!
@GrassWarz
6 жыл бұрын
Layth Grangaard subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
I like the flip flops better
@GrassWarz
6 жыл бұрын
Ben Kempa subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
I like how your using the biggest machine on your property to fix the smallest piece of equipment 😂😂😂
First let me say I'm from the UK so when I say this guy is a cowboy, it is not anything like or to do with what is a USA cowboy who I respect for there hard life they live, in the UK that term means he is a person who has little to none of any good sense and working practices, for instance his choice of tools, many of which were too light or wrong for the job in hand, in the 1st video. Come on! wearing open toed sandals whilst working on removing heavy items, this is an injury waiting to happen, safe working practices I think not, then the parts he removed, has he never heard of cleaning the parts, and keeping them all together in a safe place ready for reinstalling, instead of leaving them scattered around, no wonder he lost one of the pin lock rods, and to replace it with an under sized threaded soft piece of metal cut from a bolt is beyond belief ( the original locking rod is most likely made from high tensile steel), then he reassembles everything without cleaning anything some of the parts are in a filthy condition covered in muck, grit and grass, a recipe to disaster that will cause wear on those all important joints, getting the cylinder and ram repaired will have cost him a pretty penny I bet, all wasted, because this cowboy messes the job up with his poor working standards and practices, instead of doing it properly. You think I’m being harsh on him, yes I am I would hate to think this guy was doing any work for anybody else and getting paid for it, now that he has shown his standard of work practices on here.
@GrassWarz
6 жыл бұрын
barry edwards subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
@hunterbennett5316
5 жыл бұрын
This is a realistic repair, you could pay a dealer mechanic $2500 and you’ll get the same repair done the same way. You’re talking like these are precision instruments, they aren’t. These machines are ran in abusive, dusty and muddy conditions, usually not greased often, and don’t have .0001” tolerances. Besides it’s his equipment, he should be able to repair it how he likes without people bashing him because they’d do it differently, if you own a piece of equipment then you repair it how you feel is acceptable.
You sure don't believe in cleaning up your pins and regreasing the pins, little dirt to go with seals! never hurt anything Right!
have you ever thought about buying a camera called a gopro ? then you wont have to hold your camera,the gopro sits on your cap .
@GrassWarz
6 жыл бұрын
paul thompson subscribe to my channel Mr. Dozer D6N2 to kill extra time. I'll Subcribe to your. Favor for a favor.
I like watching you work the excavator, but your language is a little rough
Pins and women have a lot in common. The older they get the loser they damn well are... pins wore out and the holes are getting sloppy
Man you have good videos, but can do without the bad mouth and words comes sometimes. 🇺🇸🇺🇸🇺🇸
Keep your day job and don't become a leg model!